Softening Point Apparatus
Get Price Quote
1 Piece (MOQ)
Country of Origin : India
Type : Automatic
Certification : CE Certified
Application : Industrial, Laboratory
Color : Grey, Blue
Voltage : 220V
Warranty : 1 Year
Automatic Penetrometer
Get Price Quote
Material : Aluminum
Range : 620 Pen
Units : Pen/MM
Load : 200W
Usage : Laboratory
'CI' automatic penetrometer, body made of powder coated cr sheet with machined ss top, with inbuilt spirit level. dual speed automatic or manual movement with auto contact detector and automatic release and retention of plunger. full measurement range of 0-620pen in 1⁄10mm scale or1⁄100mm scale Compliance ASTM, d5, d217, d937, d1321, d1403, d2884, d4950; ip 49, ip50, ip179, ip310; iso 2137; din 51 579, din 51 580, din 51 804; ftm 791-311, ftm 791-312, ftm 791-313; aocs cc 16-60; aacc 58-14; nf t60-119, nf t60-123, nf t60-132, nf t66-004, bs: 1377 Application Used for penetration tests on petroleum products and for consistency tests on a wide range of food products, cosmetics, pastes, destempers and other solid to semi-solid products. consists of a dial scale 0-40.0mm with 1⁄10mm sub divisions. (0-400 penetration scale). suits cones and needles to perform all the astm tests on lubricating greases, asphalts, petroleum waxes. compact design facilitates transport for field use. geared dial and plunger movement for accurate placement of the tip of the needle or cone on the surface of the sample. Models 11045-00 standard penetrometer 11045-01 standard penetrometer with digital timer. 11045-02 fully automatic penetrometer Body made of powder coated cr sheet with machined ss top, with inbuilt spirit level. dual speed automatic or manual movement with auto contact detector and automatic release and retention of plunger. Automatically timed operator programmable penetration measurements Automatic placement of penetrator on sample surface Large lcd/touch screen display Full measurement range of 0-620pen in 1⁄10mm scale or1⁄100mm scale Rechargeable battery or ac operation Can be used with any standard cones, needles and other accessories Advanced user friendly features to provide ease of operation and highly reproducible consistency measurements. User programmable penetration timing 1 to 9999 sec. Auto release of penetrator after temperature stabilization can be programmed . In-built memory to store 5 test procedures. Can be programmed for pass or fail result display. Can be connected to a printer for test result printing. For non-conductive samples the penetrator can be placed on the sample surface by using coarse and fine push button switches. Built in led lamp for greater visibility The penetrator assembly automatically returns to its home position after test. Standard Accessories 11045-03 50gm weight 11045-04. 100gm weight
Best Deals from Civil Engineering Test Equipment
Concrete Test Hammers
Get Price Quote
Material : Aluminum
Brand Name : Proceq
Weight : 1.3 Kg
Dimension : 300 x 70 x 70 mm
Impact Energy : 2,207 Nm
Thickness : Greater 100 mm
Handle Material : Glass-filled nylon
Marshall Stability Apparatus
Get Price Quote
Price : Approx. Rs 72,000 / Unit(s)
Marshall Stability Apparatus which we offer are one of the highly acknowledged products known for its compactness, good strength and long life. Our product is fabricated using three mild steel moulds along with 50Kn capacity, two compaction rammers, load transfer bar, extraction plate, steel ball, etc. Apart from this, modified version with capacity 100KN is also available with us. It smoothly functions with AC mains of 220volts. Detail : We are involved in offering an extensive range of Marshall Stability Apparatus. This Marshall Stability Apparatus comprises three mild steel mould 4 dia, 50 kN capacity electrically operated load frame with speed of 5.08cm/min, two compaction rammers 4.5 kg. weight and 457 mm fall and one each of breaking head assembly with provision to hold dial gauge, load transfer bar, compaction pedestal (manually operated) with mould holder, extraction plate and steel ball. We provide this product with 25 kN capacity proving ring with our calibration chart and dial gauge 0.01 x 25 mm travel. Modified Marshal Stability Apparatus, with 100kN capacity load frame, suitable for 6 samples Tar Viscometer After confirming each and everything from customers, we present them a personalized assortment of Tar Viscometer. Offered Tar Viscometer is extensively used for determination the viscosity of road oils and cut back bitumen. Our product comprises copper bath with cup of 10 mm or 4 mm orifice and sleeve, with lifting clip and ball. The assembly placed on suitable stand. Also, it is suitable to operate on 220 Volts AC mains. Features : Compact design High tensile strength Long service life
Bouffant Cap Set
32 Per Set
50 Set(s) (MOQ)
Size : 15-20cm
Shape : Common
Color : Multi Color
Season : All
Pattern : Plain
Feature : Comfortable
Gender : Both
Slump Test Apparatus
Get Price Quote
Material : Stainless Steel
Power : 0.5kW
Rod Diameter : 16 mm
Finishing : Galvanized
Rod Length : 600 mm
Top Diameter : 20 mm
Cone Penetrometer
Get Price Quote
We are offering cone penetrometer - (mpc-02) for determining the consistency of masonary mortar. salient features specifications: consists of a movable bearing rod to which a cone 145mm. Long and 75mm. Dia at a base is fixed. The bearing rod passes freely through a bracket which is provided with release mechanism. A dial graduated in mm with rack and pinion is provided for measuring th
Load Cell Frame
Get Price Quote
Perfectly Balanced Load Cell arrangement with frame and HX711 interface ready to use with nay of the microcontrollers.
loading frame
Get Price Quote
Material : Stainless Steel
Phase : Single
Surface Finishing : Polished
Power Source : Electric
Frequency : 50-60 Hz
Voltage : 240 V
loading frame
Get Price Quote
Voltage : 240 V
Material : Stainless Steel
Phase : Single
Surface Finishing : Polished
Power Source : Electric
Frequency : 50-60 Hz
Shear Stability Tester
Get Price Quote
Pump : 2 Plunger
Reservoir Capacity : 250 mL
Lubricants are often subjected to mechanical shearing, for example in automotive engines. This shearing causes lubricants to lose their viscosity. When subjected to sufficiently large number of cycles of shear, viscosity may drop below acceptable levels and may call of replacement failing which surfaces may become prone to higher wear. Even lubricants that have consistent viscosity through a wide temperature range (high viscosity index) may still be susceptible to loss of viscosity when subjected the mechanical shearing. Shear Stability Tester is an instrument used to determine an oils ability to retain its viscosity over a number of cycles of shear. The test oil is first measured for its initial viscosity after which it is subjected to shearing in intervals of 30 cycles. Viscosity is measured and compared to the oils initial viscosity following 30, 90 and 120 cycles. Oils that show a lower drop in viscosity over the duration of test are said to have better shear stability than oils that exhibit a relatively higher drop in viscosity. Features Floor standing designIncluded safety enclosure Options Recirculating chiller (if no water line is available)
sand testing machine
Get Price Quote
We have a complete devout in developing highly demanded Foundry Sand Testing Machine. We bring forth the highly versatile and next generation equipment that is widely acclaimed for its maintenance free design. The offered equipment is fitted with innovative components and demanded widely for measuring the permeability number of sand.
Slump Test Apparatus
2,100 Per Piece
As per IS : 7320
Feature : High work capacity,Corrosion resistant,Completely tested
Specification : It comprises of slump cone (Top dia100mm, Bottom dia 200mm and Height 300mm) with handles made of mild steel sheet, a chrome plated graduated tamping rod 16mm dia x 600mm long , rounded at one end and a hexagonal base plate
Dynamic Cone penetrometer
18,000 Per Piece
Color : Silver
Weight : 15 kgs approx
Diameter : 17mm
Material : mild steel
Usage/Application : soil testing
Finishing : machining finish
Slump Cones
Get Price Quote
We offer our customers a range of functionally advanced Slump Cones that are manufactured with precision. Our full range of products is of durable nature and high tensile strength. We are one of the leading manufacturers and suppliers of compressor testing machines that find wide application in the construction industry. These machines are used to test the particular compressive strength and the sample of cubes or concrete cylinders by applying a load through this machine. We offer portable models that are very useful and convenient for transporting specimens to sites instead for testing in a standard laboratory. Supplied with special accessories, the machines can also be used safely for bricks. The machine has a load chassis with suitable plates and is equipped with a pumping unit with manometer. The machine operates manually or operates electrically according to customer requirements. Characteristics: 1) Easy to use and Useful for hollow or solid concrete blocks (using a suitable capacity machine). 2) The pressure pipes connect the load chassis and the pumping unit.
Hand Operated Load Frame
26,500 Per Piece
Material : Cast Iron
Voltage : 230 V
Phase : Single Phase
Country of Origin : Made in India
Brand Name : Smarcon
Color : Blue
Automation Grade : Manual
Power : 5 W
Glow Wire Test Apparatus
Get Price Quote
Applications: Resistance to flame and ignition test on insulating material such as CFI outer insulating material, HID lamp cap insulating parts etc System Features / Technical Data: The heating element is made of Nickel/ Chromium (80:20) wire, 4 mm in diameter The temperature sensor is made of a sheathed fine wire of Cr/ A1 thermocouple resistant to a temperature of 1000 C Self adjusting current source is used to heat the Glow-wire up to preset temperature A microprocessor based PID temperature controller is used to control temp of glow wire. (Range: Ambient to 960C, Resolution: 1°C Accuracy: 1% Display: 4 Digit Red LED) Microprocessor based digital timer is used for pre-setting the test duration (Range: 0.1 999scc) with audio alarm to remove the test sample from the glow wire tip Digital time interval meter to record the burning time of the sample Glow wire penetration into the sample can be limited mechanically Provision to press the sample towards the glow wire tip with a force of 1 Newton In Auto models motorized forward and reverse motion for the movement of specimen with additional manual jog switches Automatic start of the test and draw back of the sample after the pre-set test time with a single press button Manufactured confirming to IEC, BSS and IS specification.
Slump Test Apparatus
2,000 Per Piece
Material : Stainless Steel
Country of Origin : Made in India
Features : Sturdy construction,Unmatched quality,Fine finish
Soil Nutrient Tester
1 Per Piece
1 Piece(s) (MOQ)
* Big LCD display. * Print testing date, sample number, sample items, sample contents, variety etc. * Large capacity storage (time, place, fertilizers), datum can be checked at any time. * Quickly test the N, P, K, organic matter, salinity, and pH in the soil, fertilizer and plants. * The reagent included: low requirement to the storage condition, last longer, and low test cost. * With the function of time display, can automatically record and save the time of tested sample.
Construction Testing Equipment
Get Price Quote
Construction Testing Equipment, Bitumen, Cement, Concrete, Lab Equipment