Atlanta Linear Actuator
Get Price Quote
1 Piece (MOQ)
Electromagnetic Linear Push Pull Solenoid Actuator
Get Price Quote
1 Piece (MOQ)
Solenoids basically are electrical devices used to convert electrical energy into linear mechanical motion. The energy produces within a solenoid can either be used to provide a straight linear pulling action, or it may be converted to provide rotary action. In either case the magnetic pull force increases as the air gap is reduced between armature and core. We offer the following type of solenoids in variety of sizes. Single Action linear Solenoid --- A linear stroke motion from the start position to the end position. The return action is effected by some other external force / mechanism. Depending on the solenoid design, the force can be applied in a ‘PUSH’ or ‘PULL’ sense. Double Acting Linear Solenoid --- This in effect is two solenoids back to back, the stroke obtained by energizing in one of the two opposing directions from neutral. Rotary Solenoid --- Utilizes rotary motion from a neutral position when the solenoid is energized. Standard travel is 25 - 95º. Return action is via some other external means. Various factors and their relations such as Force, Stroke, Duty cycle, pushing or pulling should be considered when selecting the right solenoid. Our D.C. Solenoids are most often sought by industrial segments for various applications such as automations, printing, packaging, textile, elevators, Automobile industries and general machine tools.
Best Deals from Linear Actuators
ML7420A6033 E Electric Linear Valve Actuator
Get Price Quote
1 Box (MOQ)
Model No : ML7420A6033 E Product Type : Electric Linear Valve Actuator supply voltage : - 24 Vac ±15%; 50/60 Hz power consumption :- 5 VA signal input 0(2) Vdc :- Actuator stem retracted. Two-way valve:”open”, three-way valve port A-AB:”closed” . run time at 50 Hz :- 1 min Manufacture : Honeywell Usage : Indutrial Automation Warranty : 1 Year Origin : MADE IN TAIWAN
Electric Linear Actuators
Get Price Quote
A Electric Linear Actuators is a hardware which creates the movement along a straight line, in contrast with the rotary motion of a conventional electric motor. The linear actuator is used in automation, automotive (such as management carburetor, moving lights), in computer peripherals (disk drives and printers), valves and other areas of application where there is a linear motion. Electronic driver for 1 or 2 independent actuators or 2 synchronized actuators 12/24V 10-15AFeatures : Driver power stage with pulse width modulation (PWM) Customizable acceleration and deceleration ramps Extreme precision and control for movement and brake Current and temperature limits Stop with limit switches Parameters editable in an easy and fast way thanks to a PC interface and through a USB serial converter Control of movements in synchronous mode by encoders with Hall effect; setting of the electronic limit switches (opening/closing) Compatible with a wide range of products and different applications High efficiency and low losses of power stage It is designed as electronic driver in low voltage for the control of one or two linear actuators with DC motors through MOSFET transistors with pulse width modulation (PWM). In “sync” mode, the driver ensures the balancing of actuators also in case of extremely different loads in terms of weight, shape,or distribution on the surface, allowing a stroke without any difference between the two actuators.Technical Data : Power supply: 12 to 48 V DC, maximum ripple 20% Output current: 15 A for motor, in duty cicle S3 - 30% - 10 minutes PWM frequency 10 kHz Stand by power consumption: 50 mA @ 24 V 12 digital inputs (3 - 12 V): 8 for commands/limit switches, 4 for encoders (max 1 kHz), with operating logic programmable (positive/negative) 2 digital outputs NPN open collector (max 50 mA - 24 V): one for the fault and one programmable Dimensions : Without heat sink for currents up to 10 A: 86x72x30 mm (WxHxD) With heat sink for currents over 10 A: 86x72x50 mm (WxHxD) Signal Terminals (Vertical) Open: opening command Close : closing command Trim-1 : enabling independence for actuator 1 Trim-2 : enabling independence for actuator 2 OP-SW: opening limit switch CL-SW: closing limit switch INT-SW: intermediate limit switch Stop Encoder motor 1 – channel 1 Encoder motor 1 – channel 2 Encoder motor 2 – channel 1 Encoder motor 2 – channel 2 Digital output 1: Fault Digital output 2: programmable GND for commands, limit switches and encoder +12V for encoder supply Power Terminals (horizontal) +V: positive supply 0V: GND : M1+: actuator 1, positive supply (voltage > 0 opening) M1-: actuator 1, GND M2+: actuator 2, positive supply (voltage > 0 opening) M2-: actuator 2, GND Main Controls Open/Close: synchronous movement Trim1 + Open/ Close : movement of actuator 1 Trim2 + Open/ Close : movement of actuator 2 Trim1 + Trim12 (3 sec): homing Homing : The driver moves both the actuators in the same direction, according to an adjustable profile, amperometric threshold (controlled mechanical stop) or limit switches, depending on the configuration. It detects automatically the connection’s direction of encoders Trimming : The driver moves each actuator independently, for mechanical adjustments and a first manual alignment. It is required to check that commands correspond to the direction of movementPossibility to configures on/off delays and reverse the logic. The start is provided through fully adjustable voltage ramps. The stop is provided through electronic limit switches (or eventually mechanical limit switches), or with adjustable current limits. Signal Terminals (vertical) : Open-1: opening command for actuator 1 Close-1: closing command for actuator 1 Open-2: opening command for actuator 2 Close-2: closing command for actuator 2 OP-SW-1: opening limit switch for actuator 1 CL-SW-1: closing limit switch for actuator 1 OP-SW-2: opening limit switch for actuator 2 CL-SW-2: closing limit switch for actuator 2 INT-SW-1: intermediate limit switch 1 INT-SW-2: intermediate limit switch 2 Stop-1: stop for actuator 1 Stop-2: stop for actuator 2 Digital output 1: FAULT Digital output 2: programmable GND for commands, limit switches and encoder +12V for encoder supply Power Terminals (Horizontal) +V: positive supply 0V: GND : M1+: actuator 1, positive supply (voltage > 0 opening) M1-: actuator 1, GND M2+: actuator 2, positive supply (voltage > 0 opening) M2-: actuator 2, GND In case of one or two independent actuators : It is possible to use intermediate limit switches It is possible to configures on/off delays and reverse the logic The start is provided through fully adjustable voltage ramps The stop is provided through mechanical limit switches, limit switches for overcurrent or adjustable current limits Main editable parameters: Voltage ramps Current limits Synchronous or independent enablement Homing at the start (for sync only) Homing with current limits or limit switches (for sync only) Virtual limit switches settled with encoder pulses limits (for sync only) Values monitorable through “Monitor” and “Statistics” sections : Motors current Applied voltage Temperature Speed Active commands Operating mode General information about the operating status of the driver Using the PC interface, it is possible to : Consult the errors history (the driver stores each error and the time at which it occurred, from the last start) Decide if an error stops the operation (only advanced mode for some errors) Decide after how many repetitions of the same error the driver has to block (only advanced mode for some errors) Decide the error tripping delay (only advanced mode for some errors) The connection driver/PC is possible through an USB/UART cable converter.
GEZE Linear Sliding Door Slimdrive
Get Price Quote
Certification according to Resistance Class 2 (DIN V ENV 1627 to 1630) Note: The previously valid preliminary standard DIN V ENV 1627:1999-04 has been replaced by the European standard DIN EN 1627 et seq. Sophisticated 7cm drive with finely framed ISO fitting Passage height up to 3000mm with MONO or ISO safety glass Perfect integration and retrofitting even in the slimmest of glass façades Escape and rescue version: escape route function with drive redundancy and low-wear two-motor technology Intelligent digital control (category 2 in accordance with DIN EN ISO 13849-1): Self-learning Optimal convenience thanks to automatic learning of door behaviour to the access frequencies Can be networked and integrated into the building technology management systems via CAN bus Independent error recognition and protocolling Setting options for all movement parameters of the door Very quiet operating direct current drive; low-wear, maintenance free motor Integrated battery for emergency opening and closing in the event of a power failure Robust power supply with integrated all-pole mains switch and fuse Certified in accordance with DIN 18650 Combination options with the GEZE SecuLogic access control as well as GEZE building technology management system
Linear Actuators
Get Price Quote
Electromechanical Linear Actuator
Get Price Quote
Electromechanical Linear Actuators are electromechanical cylinders able to transform a rotary movement into a linear motion. Developed and manufactured for industrial application. Linear Actuators can offer higher linear speeds and loads at up to 100% duty cycle, even in the most extreme conditions and arduous applications. Able to work under push or pull load According to their features they can be Statically self-locking : able to sustain static load keeping the same position when the motor is switched off Statically non self-locking: the load can be sustained with a brake motor They are capable of maintaining constant speed with a varying load, at a very low noise level. Their motion can be simply a push-pull “ON-OFF” action, also they can become servomechanisms working as controlled axes, by means of accessories such as encoders or potentiometers for the positioning control, motors with tacho-generator and servo drives. Their installation is simple and not expensive: it requires just a front and rear hinging as for standard hydraulic and pneumatic cylinders. They can perfectly replace pneumatic or hydraulic cylinders being able to perform Accuracy in push-pull motion Accuracy in stopping position Position holding under load (self-locking) Energy consumption only while moving High safety in lifting a load (internal safety devices available) Use in low temperature environment without freezing problems Use in high temperature environment without fire risk Linear Actuators have a wide application fieldThey are intended for Industrial applications where it is necessary to perform in total safety or to control a linear motion while moving, turning over or lifting a load. The wide range of sizes, stroke lengths, linear speeds, motors and accessories makes it easy to adapt these products for new applications or replace even complicated mechanical solutions and hydraulic or pneumatic cylinders improving the applications final performances.
ELECTRO MECHANICAL LINEAR ACTUATOR
Get Price Quote
Linear Actuator
19,000 - 20,000 Per Piece
Linear Actuators
Get Price Quote
Linear actuator is an electrically operated device which help push or pull objects. These actuators can handle a lifting capacity of 200 – 12,000 Newton. They are quiet, safe and has a clean and accurate motion control. Linear actuators are widely used for applications like hospital bed, dental chair, ICU beds, OT tables and so on. Because these actuators are easy to install and required no maintenance most hospital bed and furniture manufactures prefer these actuators.
Linear Actuator
40,000 Per Piece
Linear Actuator
Get Price Quote
Linear Actuators
Get Price Quote
Rotolinear systems offer linear actuators. These actuators are with ball screws or lead screws depending on the application and normally with 12v dc /24v dc motor + 110/230vac converter + remote hand set. It is used for furniture, satellite, automation, dish antenna, fitness equipment, furniture’s, hospital equipment ect. The standard stroke available is upto 612mm and the max dynamic load carrying capacity is 800 to 8000n and static around 13600n. The speed of ball screw driven linear actuator will 4.5- 65mm/ sec. The protection will be ip65; ip54 depending on the models and preset limit switches is included. The optional accessories like potentiometer, hall effect sensors
Linear Drive
Get Price Quote
High speed linear actuator
Get Price Quote
Electromagnetic Linear Push Pull Solenoid Actuators
Get Price Quote
Solenoids basically are electrical devices used to convert electrical energy into linear mechanical motion. The energy produces within a solenoid can either be used to provide a straight linear pulling action, or it may be converted to provide rotary action. In either case the magnetic pull force increases as the air gap is reduced between armature and core.
Electromechanical Linear Actuator
120,000 Per unit
Linear Actuators
Get Price Quote
Linear Actuators, Rehfuss Ac Motors & Geared Motors
Linear Actuators
Get Price Quote
Linear Actuators, Screw Jacks, Hospital Bed System -HBS-02
Linear Actuators
Get Price Quote
Linear Actuators, Collet Chucks, Electric Actuator