Begapt Solutions Okhla, Delhi

  • Plc Based Synchroscope

    Plc Based Synchroscope

    Request for Price

    The operation of connecting an alternator in parallel with another alternator or with common bus-bars is known as synchronizing. Generally, alternators are used in a power system where they are parallel with many other alternators. It means that the alternator is connected to a live system of constant and constant frequency. Often the electrical system to which the alternator is connected, has already so many alternators and loads connected to it that no matter what power is delivered by the incoming alternator, the voltage and frequency of the system remains the same. In that case, the alternator is said to be connected to infinite bus-bars. Traditional system uses Full Bright Lamp method or Full Dark Lamp method for the synchronization of alternator. This system is automatic synchronization of the alternator using PC based software and communicating hardware.   Reading of Terminal voltage of all phases (R,Y,B) of grid and alternator into Software. Display of Terminal voltage of all phases (R,Y,B) of grid and alternator on to 3 ½ digit panel meter. Reading of frequency of grid and alternator. Display of frequency of grid and alternator on to 31/2 digit panel meter. LED based indication of the R,Y ,B phase power. Accurate reading of the phase differences. Graphical display of the R-Y-B waves of alternator and Grid. Manual and auto mode for the sync of alternator to grid. Electrical control system to start DC motor coupled with alternator. Separate load bank for connection after synchronization of alternator. 

    ...more
    Get Best Price
  • Optical disc counting system

    Optical disc counting system

    Request for Price

    The BS-Count CDR/BDR is the leading product for the  counting of CD ,DVD and Blue Ray Disc  at the end of the line  for the Optical disc manufacturer. The system provides ease-of-use, Fast response ,Accurate counting and detect mixing of the products . Begapt’s Multi level threshold  technology provides reading of the stack with more than 100 disc. Configured with a 5 MP  CMOS camera, Megapixel lens , special design lighting , Controller and our high performance software gives reliable fast and accurate counting of the disc. System Features Accurate Fast response Detects mixing of products 5 MP camera Megapixel Lens Special Design light Count CD, DVD and Blue Ray Count more than 100 Disc in  stack Audio count output

    ...more
    Get Best Price
  • motor control

    motor control

    Request for Price

    We provide state of art motor drive and control solutions which include complete hardware and software tools for servo, stepper, DC, induction, and synchronous motor. System also includes custom hardware and software development for the test and measurement requirement for the setup.     System Features Control for stepper, Servo, DC, induction and synchronous motor. Motor control in closed loop or open loop. Drive panel with control using Daq card. Speed control using Analog output or PWM. High PPR encoder or Techogenerator. NI LabVIEW based software for control. Data acquisition or control for other hardware (Pressure,Force,Distance,Current etc). Extensive reporting tools.

    ...more
    Get Best Price
  • Label Printing Unit LPU

    Label Printing Unit LPU

    Request for Price

    Typically when a company implements a barcode printing solution, it consists of a computer (either stand-alone or on a network), software, and the printer itself (table-top or mobile). LPU Unit from Begapt, enables Serial Port Enabled Printer to run independent print operations without the need for a computer. Reduce IT hardware costs, lower total cost of printing and create flexible work processes that improve productivity and reduce the opportunity for errors.     The abilities of the LPU Includes: Operate independently of a Computer. Reads Values (X1-X2), Angle between Line L1 and L3, Angle Between line L2 and L4. Connect to USB Barcode Scanners. It has built in RTC for time display. Easy to add new parameter for reading. Small Rugged and light weight (Dim-150*150*150mm). Print command through PASS & FAIL signal (Relay Input). Advantages: Easy Installation. Design your own label as per demand. Low Cost-Saves on Cost. Any printer with Serial port can be connected. LCD segment display.

    ...more
    Get Best Price
  • Label Inspection System

    Label Inspection System

    Request for Price

    Begapt label inspection system is 100% automatic quality inspection of the label.System reads all types of barcode,pharmacode ,2d code ,RSS code ,PDF codes batch codes (OCR/OCV) on the production line at very high speed. System Features Multi camera support.. Reads all types of barcode, 2D code, RSS code Pharmacode,PDF code Accurate reading of batch codes(OCR/OCV). omni direction codes reading. Label color inspection. Embossed char reading. Codes printed on aluminum foil. Faulty label rejection. FDA(21 CFR part11) complaint. Extensive reporting module. Remote monitoring.

    ...more
    Get Best Price
  • wiring harness assembly

    wiring harness assembly

    Request for Price

    Guided Harness Assembly system on Begapt’s mPC platform acts as an Aid for Wiring Harness Assembly. It guides the operator to pick up wires/connectors from designated positions and place it at designated poles through blinking of LEDs. It also has a feedback mechanism to ensure wires are correctly placed and hence ensures total quality besides saves time and effort. Finally a guided harness assembly system that is easy to set up and use!. The base unit provides 120 Test Points in enclosures measuring 12” X 8” X 8” expandable upto 1280 Points. Its structure allows test points to be distributed around the device under test reducing the length and complexity of wiring. The CPG user interface simplifies test program development by providing a step-by-step process with prompts. Connector detail is created once and stored in a library for use in multiple test programs. Completely Standalone system with Option of remote programming. Powerful solution which can manage printers and scanners.  

    ...more
    Get Best Price
  • Fuse Box Inspection System

    Fuse Box Inspection System

    Request for Price

    Fuse box consist of fuses of different color and rating which are to be placed at designated places.However sometimes the color coded fuses are not placed in their designated places during the assembly on the fuse box. This is a defect in the finished product which needs to be identified and corrected.The supplied system comprises of Industrial Cameras;Pneumatic Arrangement; digital control cards etc. The software has OCR technology for character recognition as well. System Features Single or Multiple camera system. Pneumatic or electromagnetic locking. Compnent Sensing. Uniform and effective illumination LED light. Easy integration with barcode scanner. Label Printing after test. Aluminum extruded based design. Easy to program. Extensive reporting module. Remote monitoring.  

    ...more
    Get Best Price
  • Diffused Reflectance Measurement

    Diffused Reflectance Measurement

    Request for Price

    Diffused reflectance measurement set-up is suitable for measuring diffused reflectance from a textured and or anti reflection coated (ARC) Si wafers of full size 6”x 6” or 5” x 5”. especially designed detectors are used to detect the reflected light from the Si wafer surface. This set-up is designed for quick measurement of diffused reflectance from the full size wafer to quantify the quality of texturing or ARC films on Si wafers. In this design, almost full area of the Si wafer is illuminated by a collimated beam of light using a halogen lamp source. The set-up is very rugged and can be used on a shop floor with ease.     System Features Especially designed to measure and compare the diffused reflectance non-destructively of a full 5”x 5” or 6”x 6” textured or ARC coated Si wafer. Very low measurement time. Highly sensitive (resolution 0.01 %) especially in the low range (2-20%) of diffused reflectance which is required to test the quality of texturing and ARC coatings. Can be used to detect non-uniformity of texturing also . Very easy to use and does not require trained personnel or a clean room. Very easy to calibrate w.r.t. standard samples. The operation is computer controlled and all the data can be saved and retrieved as and when required for comparing the results with the final cell output. Out-put of the set-up can be used to optimize the texturing process to enhance yield of solar cells. Early detection of bad texturing with this set-up can reduce wastage of expensive Si wafers and associated process cost.

    ...more
    Get Best Price
  • Cluster Inspection System

    Cluster Inspection System

    Request for Price

     Begapt Cluster Inspection System is non contact type inspection system for cluster at the end of the production line.Cluster components like warning bank,Speedometer,RPM meter,Fuel Guage,Pressure Guage,Odometer etc are given test signal and verified by the camera. System Features PC based Test System with LCD display as HMI Quick setup for pointers calibration, display, tell tales, analog and digital I/O and communication test Application independent mega-pixel vision system Variant manager handles hundreds of variants. User can create and delete variants Test application integrated release management-Optional feature User based customized feature development Extensive report generation and data recording feature Customized Label generation on OK/Pass Low cost of ownership Remote Monitoring.

    ...more
    Get Best Price
  • Clip Tester

    Clip Tester

    Request for Price

    This is a low cost system on Begapt’s mPC Platform for detection of missing clips in wiring harness assembly. In the assembly of wiring harness, clips are needed to be tightened at designated places. At few instances clips are not placed due to manual error. Detection of missing clips if any is required.     Enables to test the clips easily, displaying the errors detected in the wiring harness through glow of LED on the designated fixture. It detects the following errors: Missing Clip Excess Clip When the test is correct Potential Free contact shall be generated. It is also possible to print a label at the end of OK Test. The system can be run in both modes: Step Mode: Detection of Clips in fixture is done one at a Time in any order. Total Mode: Detection of Clips is done Only when All clips are inserted at One time. Detects missing & Extra Clips. Can work in Both Modes- Step & Total. Easy to Program through Remote LAN. LCD Display for Model selection. Model selection through Barcode. Easy interfacing with Label Printer-No Extra PC required. Fast and Easy to Operate. Expandable upto 1280 Pts.   Standalone System. Remote Programming Feature. Away Programming. GUI for System Program. One Platform-Many Products. Ease of Interface. Modular Platform

    ...more
    Get Best Price
  • Catalytic Converter Inspection System

    Catalytic Converter Inspection System

    Request for Price

    This System reads embossed number and 2D code on the monolith metallic envelop and barcode and alphanumeric char on the visible circular ceramic side of the monolith. System comprise of two monochrome camera with suitable LED lighting and dedicated vision controller.     System Features Two camera based system. Reads embossed 2d code and char with high accuracy. Special light for feature extraction of embossed part. Communicate with embossed char printing machine. Reads barcode and alphanumeric character on the ceramic part of the monolith. OK part marking. Aluminum extruded based design. Easy to program. Extensive reporting module. Remote monitoring. Recognition Embossed numeric character(OCR/OCV) Alphanumeric character(OCR/OCV). Barcode(codabar,code39,code93,code128 ,EAN8,EAN13,Interleaved 2or 5,MSI,UPCA GS1 databar) . Embossed Data Matrix

    ...more
    Get Best Price
  • BS Data Acquisition Systems

    BS Data Acquisition Systems

    Request for Price

    BS-Daq box deliver very high performance measurement of electrical data. It can be used for recording of field data and processing of field data through special software supplied.Daq box contains high resolution analog input, high resolution analog output, high speed digital input/output and counter time with dedicated signal conditioning for LVDT, load cell, RTD and thermocouple.   Box consist of 8 Analog inpu,2 analog Output, 8 DO/DIa and 2 counter. Signal conditioning for Load cell, RTD, Thermocouple and LVDT. Real time hardware LVDT,Load Cell,Thermocuple RTD. LabVIEW based software for acquisition of data. Software to analyze acquired data. Driver for MATLAB. Data acquisition or control for other hardware (Pressure,Force,Distance,Current etc). Extensive reporting tools.

    ...more
    Get Best Price
  • Automotive Headlamp and Bulb

    Automotive Headlamp and Bulb

    Request for Price

    A headlamp is a lamp attached to front of the vehicle to light the road.Headlamp mainly consist of moulded part,Automotive bulb,Reflectors, electrical circuits.Production defect of component or wrong assembly of component lead to bed performance of the headlight.     Solution Offered: Head lamp component  presence absence detection during assembly. lamp(H4,H7)  different parameter dimension measurement. Automotive bulb sheild position with respect to glass.

    ...more
    Get Best Price

Be first to Rate

Rate This

Select the service for which you are writing review for this business

How would you rate the business?

What would you like other to know about this business, based on your experience?

Minimum 20 characters!

About the Company

  • Primary Business Retailer
  • Secondary Business Type Manufacturer / Exporters / Wholesale Suppliers

Opening Hours

  • SUN : Closed
  • MON : 9:30 AM - 6:30 PM
  • TUE : 9:30 AM - 6:30 PM
  • WED : 9:30 AM - 6:30 PM
  • THU : 9:30 AM - 6:30 PM
  • FRI : 9:30 AM - 6:30 PM
  • SAT : 9:30 AM - 6:30 PM
Begapt is a Customized Solution provider House partnering with a large network of manufacturers, distributors and researchers with the common goal to provide global, advanced and innovative solution to our customers. Combining software expertise with Application Integration; we offer a unique service in - that of System Supplier and System Integrator - giving us unparalleled expertise and experience in technology for Test Equipment Developments. Our systems are some of the most innovative and advanced Test & Measurement solutions in the field of Vision, Control, Signal Processing, Embedded & Motion developed on National Instruments (NI)-LabVIEW platform successfully deployed in many places including Industries & Research Institutions. Our solutions enable manufacturers to realize significant economic paybacks by increasing the quality of manufactured parts and improving the productivity of manufacturing processes.
Read More »

Contact Information

Begapt Solutions

  • Begapt Solutions
  • B-185 2nd floor DDA shed Okhla phase 1 New Delhi-110020 India
top