Back Back
Acid Resistant Epoxy Paints
Get Price Quote
We offer Acid Resistant Epoxy Paints that are concentrated sulfuric acid resistant. The Novolac Epoxy Coating For Concentrated Acids is based on advanced coating formula. Typically, the Acid Resistance Epoxy Paints Coating is a two - component, rigid, novolac epoxy coating with excellent resistance to concentrated sulfuric acid, other strong acids and bases, and many chemicals found in industrial environments. When seeded or blended with aggregate, it can be used on properly prepared concrete and steel substrates to provide a chemical resistant surface with excellent slip/skid resistance and wear characteristics. This product is ideally suited for use in containment areas requiring resistance to strong mineral acids, Acid Resistance Epoxy Paints will bond to prepare dry and damp concrete substrates and cures to a tough, blush free, tile like surface. When used outdoors, the coating is freeze/thaw resistant and will not embrittle, however it will acquire a chalky surface when exposed to sunlight. The standard color is concrete gray (tan gray).Features Convenient 2:1, by vol. mix ratio Fast cure for short downtime Cures to a tough, blush-free, tile-like surface Bonds to dry and damp substrates without primer Does not embrittle when exposed to direct sunlight Resistant to most strong mineral acids and bases Environmentally safe - 0 VOC solvents Limitations : Do not apply on wet substrates. Minimum installation and cure temperature is 50°F. Apply after daily substrate temperature has peaked. Substrates on or below grade must have a functioning vapor barrier to minimize the potential for blistering or delaminating of the applied coating. Broadcast aggregate must be resistant to the chemicals used in the exposure area and must be completely encapsulated by a topcoat. Exposure to 98% sulfuric acid will cause formation of a reddish surface film that can be removed by washing with water. Do not add solvents or otherwise thin this material.Packaging & Colors : Package sizes of Part A + Part B are 3 and 15 gallons. Standard color is tan-gray; black, white and brick red custom colors available.Shelf Life : Three years minimum in unopened, original containers when stored between 60 and 90° F in a dry place away from sunlight. Remixing of components may be required upon long-term storage.Surface Preparation : Concrete surfaces may be dry or damp (not wet) though dry substrates are preferred and must be sound and free of all bond-inhibiting substances. Prepare surfaces in accordance with ASTM D 4259 or ACI 503R and ChemCo Systems' specific recommendations. Cleaned concrete surfaces should have a minimum strength of 250 psi in direct tension. Steel surfaces should be cleaned to "white metal" according to SSPC SP 5.Mixing : Acid Resistance Epoxy Paints is a two-component system. The resin to hardener (Part A : Part B) mix ratio is 2 :1, by volume. Read all material safety data (MSDS) information before handling the product. Wear safety glasses and clean neoprene rubber gloves when handling the materials. Premix the individual components before use. Transfer appropriate quantities of Part A and Part B into a mixing container. Use quantities that can be applied before the pot life of the mixed material expires. Blend thoroughly using a Jiffy mixer blade attached to a low speed (350 - 750 rpm) electric or pneumatic drill. Proper mixing will take 2 - 3 minutes. In cold weather, pre-conditioning the components to 70-85°F will allow easier mixing and application.Installing : The recommended applied thickness for floor and wall coatings is two coats minimum at 6 - 8 mils per coat. Apply in multiple thin coats rather than one thick coat using a stiff bristle brush, short nap roller, squeegee or two-component spray equipment. For optimum chemical resistance, 3 coats are recommended. Subsequent coats may be applied as soon as the previous coat is “touch” dry (6 - 7 hr @ 70°F). Avoid excessive cure times between coats. The recommended applied thickness for floor surfacings is single or multiple coats at 20 - 30 mils per coat. Pour mixed material onto the substrate and spread to the desired coverage with e V-notch trowel or squeegee. Aggregate, if used, must be broadcast onto the coating within 15 minutes of application. The recommended aggregate size is #20 x 40 or #30 x 50 mesh. Typical aggregate broadcast rates are .75 - 1.50 lb/sq ft.Clean up : Excess mixed product is best removed from the work area end tools before it hardens. Use of rags and solvents such as acetone or heavy-duty detergents facilitate cleaning. Cured product may be removed from tools by soaking in an epoxy stripper.
Acid Resistant Chlorinated Rubber Paint
250 Per Litre
chlorinated rubber is a premium quality, single pack, unmodified chlorinated rubber finish. it is resistant to salt spray, all types of acids, impermeable to water and exhibits excellent resistance to mould and fungus growth. chlorinated rubber can be applied over correctly prepared and primed steel and concrete surfaces. primary uses fishing bins preparation of substrate surfaces showing heavy scale or surface rust should be treated with protec metal conditioner and degreaser. heavily rusted surfaces should be abrasively blast cleaned. cleaning : before and after any sanding operation, the substrate must be thoroughly degreased with & grease remover to remove all traces of dirt, oil, grease, silicone, wax etc. drying times will vary dependent on temperature, flash off between coats, number of coats used. is suitable for brush application on small areas. 37% volume solids (depending on colour).
Best Deals from Acid Resistant Paint
Acid Resistant Epoxy Paints
Get Price Quote
Acid Resistant Epoxy Paints, Food Grade Epoxy Paint, Industrial Greases
