Powder Dispensing Booth Dealers in Chennai (19 products available)

• Air Flow Rate: 0.45 + 0.1m/sec

The Raw materials and compounds are refilling, weighing, filling, and sampling. It is provided with high efficiency HEPA filter, which averts the airborne dusts by down flow of air technique. The unit eliminates powder contamination to protect the operator and the surrounding environment.The weighing room is one kind of clean equipment which used in micro-organism research, pharmacy and scientific experimentation, it can supply the single and multi-way airflow, and clean air (HEPA AIR) will be circulated in the working area, the other part will be exhaust outside, it can make the working area negative pressure to prohibit cross population, it can guarantee the working area with high clean grade.

• Power Supply: 230V single phase, 50 Hz

Powder containment booths are used to control the hazardous emissions of powders, dust or vapors during powder dispensing, product sampling, or bag dispensing, etc., without risk to the operator or environment. The downdraught prevents airborne dusts caused by weighing and dispensing operations rising into the operator's breathing zone. The air forced downwards is extracted at low level into the booth's filtration system where dust particles are contained at each level of filtration prior to being re-circulated back into the booths' air stream.

• Direction of flow:: Vertical

Dispensing Booths with its open-fronted design, this type of system affords comfort of access for product, operator and environment. Reverse laminar flow powder dispensing booths (Also called powder containment booths) protects the operators from toxic chemicals raw materials used for manufacturing of tablets, medicines, capsules etc from external contamination during the process of weighing or measuring. It is ideal where a high degree of flexibility is desired. Containment is achieved by air movement. Our down flow booths are workstation are available in a variety of air-handling models. When the Booths is operating under normal conditions air is pulled through the main working chamber to exhaust grills, normally situated in the rear of the Booths, suppressing air-borne dust away from the operators breathing zone. Down flow Booths and Workstation provide a safe, controlled working environment and are called upon to carry out a wide range of operations.

Powder Dispensing booths are used to control the hazardous emissions of powders, dust or vapors during powder dispensing, product sampling, or bag dispensing etc., without risk to the operator or environment.

  Mycron Air Tech make Powder containment booths are used to control the hazardous emissions of powders, dust or vapors during powder dispensing, product sampling, or bag dispensing, etc., without risk to the operator or environment.The downdraught prevents airborne dusts caused by weighing and dispensing operations rising into the operator's breathing zone. The air forced downwards is extracted at low level into the booth's filtration system where dust particles are contained at each level of filtration prior to being re-circulated back into the booths air stream. The Powder Dispensing/ Sampling Booths are designed to give mixed air flow stream for product, operator and environmental protection and used to control the hazardous emissions of dust powder during powder dispensing / sampling process. 0.3 micron downward air stream deflects air-borne dust away from the operator breathing zone which is caused in handling operation. Dust particle available is being filtered at three levels of filtration prior to being circulated back to the booths air stream. For filling, refilling, weighing & sampling of Raw material & Components.

Immunotech” The manufacture of oral solid dosage forms such as tablets is a complex multi-stage process under which the starting materials change their physical characteristics a number of times before the final dosage form is produced. Traditionally, tablets have been made by granulation, a process that imparts two primary requisites to formulate: compatibility and fluidity. Both wet granulation and dry granulation (slugging and roll compaction) are used. Regardless of whether tablets are made by direct compression or granulation, the first step, milling and mixing, is the same; subsequent steps differ. Numerous unit processes are involved in making tablets, including particle size reduction and sizing, blending, granulation, drying, compaction, and (frequently) coating. Various factors associated with these processes can seriously affect content uniformity, bioavailability, or stability. Sampling/Dispensing is the first step in any pharmaceutical manufacturing process. Sampling/Dispensing is one of the most critical steps in pharmaceutical manufacturing; as during this step, the weight of each ingredient in the mixture is determined according to dose. Dispensing may be done by purely manual by hand scooping from primary containers and weighing each ingredient by hand on a weigh scale, manual weighing with material lifting assistance like Vacuum transfer and Bag lifters, manual or assisted transfer with automated weighing on weigh table, manual or assisted filling of loss-in weight dispensing system, automated dispensaries with mechanical devices such as vacuum loading system and screw feed system. Issues like weighing accuracy, dust control (LAF booths, glove boxes), during manual handling, lot control of each ingredient, material movement into and out of dispensary should be considered during dispensing. Immunotech” The manufacture of oral solid dosage forms such as tablets is a complex multi-stage process under which the starting materials change their physical characteristics a number of times before the final dosage form is produced. Traditionally, tablets have been made by granulation, a process that imparts two primary requisites to formulate: compatibility and fluidity. Both wet granulation and dry granulation (slugging and roll compaction) are used. Regardless of whether tablets are made by direct compression or granulation, the first step, milling and mixing, is the same; subsequent steps differ. Numerous unit processes are involved in making tablets, including particle size reduction and sizing, blending, granulation, drying, compaction, and (frequently) coating. Various factors associated with these processes can seriously affect content uniformity, bioavailability, or stability. Sampling/Dispensing is the first step in any pharmaceutical manufacturing process. Sampling/Dispensing is one of the most critical steps in pharmaceutical manufacturing; as during this step, the weight of each ingredient in the mixture is determined according to dose. Dispensing may be done by purely manual by hand scooping from primary containers and weighing each ingredient by hand on a weigh scale, manual weighing with material lifting assistance like Vacuum transfer and Bag lifters, manual or assisted transfer with automated weighing on weigh table, manual or assisted filling of loss-in weight dispensing system, automated dispensaries with mechanical devices such as vacuum loading system and screw feed system. Issues like weighing accuracy, dust control (LAF booths, glove boxes), during manual handling, lot control of each ingredient, material movement into and out of dispensary should be considered during dispensing.

• Type: Powder Dispensing Booth
• Application: Laboratory
• Weight: 1000-2000kg, 2000-3000kg, 3000-4000kg, 4000-5000kg
• Color: Black, Blue, Brown, Grey, Light Green, Light White
• Voltage: 110V, 220V, 380V, 440V
• Condition: New, Used
• Power: 1-3kw, 3-6kw, 6-9kw, 9-12kw
• Driven Type: Electric
• Warranty: 1year, 2years
• Noise level :: 60-65 decibels

• Inner Dimensions: 600x600x1800 mm,900 x 600 x 1800 mm,1200 x 900 x 1950 mm

Cleanair make Powder Dispensing Sampling Booths are designed to give mixed air flow stream for product, operator and environmental protection and used to control the hazardous emissions of dust powder during powder dispensing sampling process. 0.3 micron downward air stream deflects air-borne dust away from the operator breathing zone which is caused in handling operation. Dust particle available is being filtered at three levels of filtration prior to being circulated back to the booths air stream. For filling, refilling, weighing & sampling of Raw material & Components

REVERSE LAMINAR FLOW POWDER DISPENSING BOOTHS (Also called POWDER CONTAINMENT BOOTHS) protects the operators from toxic chemicals / raw materials used for manufacturing of tablets, medicines, capsules etc from external contamination during the process of weighing or measuring. The Powder Sampling & Dispensing Booths are contains four important components such as: Return Air Primary Filter (also called as First Stage Pre Filters) Intermediate Secondary Filter (also called Second Stage Fine Filters Supply Air Final Filter (also called as Final Stage Mini-Pleat HEPA filters) Motorized DIDW / SISW blower unit When the Sampling / Dispensing booths are switched on, the blower unit creates a suction pressure through the primary filter & intermediate filter, which removes dust particles of above 10 micron & 5 micron size in the first and second stages. Subsequently, the partly filtered air passed to the HEPA filters, where the particles or substances of 0.3micron size and above are removed. Finally the ultra clean filtered air supplied to the working safe zone as a uniform airflow to perform precisionfor raw-material containment purpose

Dispensing Sampling Booths are recommended for mixing, weighing & dispensing of powder avoiding distribution of powder particles throughout the work area. These units are used to control the hazardous emissions of powders, dust or vapors during powder dispensing, product sampling, or bag dispensing, etc., without risk to the operator or environment.Standard Sizes: 4'x3'x 7’,4'x4' x 7’,6'x4' x 7’. DispensingSampling Booth can be custom engineered as per requirement.

Powder Containment Booths, bio-safety cabinet, Scrubber System

powder containment booth, Modular Operation Theatre, Modular Clean Room

Powder Dispensing Booth, air shower entry systems, Scientific Instruments

Powder Dispensing Booths, Fume Cupboards, FRP Fume Hood, Laboratory Trolleys

Powder Dispensing Booth, Laminar Air Flow System, LAB CUPBOARD

Powder Dispensing Containment Booth

Powder Dispensing Booth

Powder Dispensing Booth, SS Lab Tray, Flexible Duct Work