Gasket Prodcuts George Town, Chennai, Tamil Nadu

Product Description Asbestos dry plaited general steam and insulation packing for hot gases, oven, autoclaves, etc., conforming to IS Specification 4687 Type of Product – White Dry Asbestos Plaited PackingModel No – 1000 Round /squareMax. Working Temperature – 350°C

Product Description High-performance, non-rusting titanium-reinforced epoxy engineered for making repairs to machinery and equipment that can be precision machined. Withstands heavy loads in hard chemical envirnoments. KEY FEATURES Excellent temperature resistance (350°F) High compressive strength (15,200 psi) Resistance to chemicals and most acids, bases, solvents, and alkalis Qualifies under Mil Spec MIL-PRF-24176C, Type I Listed under NSN stock #8030-01-335-0562

Product Description Steelgrip Electrical Tapes have been developed from carefully selected backings and adhesive systems. The adhesive used in the manufacture of the tape have been developed with a special formulation to withstand different classes of temperature from Class A-105°C to Class H-180°C and includes Rubber, Acrylic and Silicon based formulations.Detailed Product Description Applications Electrical cables insulating Cable wrapping and bundling Color coding, directional marking, marking out rehearsal areas Cable reinforcing and protecting Electrical repair Features Fire-resistant. Non toxic (in room atmosphere conditions) Color: Red,Blue,Yellow,Green,Black

Product Description Stainless steel-filled epoxy putty for patching, repairing and rebuilding stainless steel food processing equipment KEY FEATURES Non-rusting Bonds to ferrous and non-ferrous metals NSF certified for potable water applications Acceptable for use in meat and poultry plants Listed under NSN stock #8030-00-268-7934

Product Description  Spiral Wound GasketsConstruction: Special Spring like Metal strips are wound with an Asbestos Filler by a special process to assure a leak proof seal. The sealing is done by the Asbestos Filler and the metal strip provides the spring. This combination of metal and soft asbestos Filler piles compresses to its predetermined thickness under bolting pressure and thereby preventing leakage within the limit of its specified pressure and temperature ranges. With the addition of Centering devices, adapt  Spiral Wound Gaskets to use on many types of flanges and closures. Materials: Standard materials are type 304 Stainless steel with white Canadian (Chrysotlie) Asbestos Filler.

Product Description Rustolene is a powerful rust dis-integrating solution. It is a quality product that has been a trusted for Rust removing for years. This is a multipurpose maintenance aid and significantly reduces the maintenance cost. It is specially formulated to fight rust, which makes it indispensable to industrial plant, factories and garages. Overall Rustolene acts as a dis-integrator, dismantler, Lubricator, decarboniser & cleaner The active ingredients in Rustolene attack the point where rust and metal parts are bound together and consequently eliminate rust from the surface. It also penetrates the tightest of joints reaches between the finest of threads and enters the innermost points of inaccessible mechanisms USAGE: Used in industries for rust disintegration and lubrication for pipelines.*Opening of jammed nuts & bolts* Pipeline* Crushing & Grinding Equipments* Valves & Pumpset.* Motor Power Generators* Lifts, Crane, Hoists, Sprocket.* Storage Tank* Compressors 7 Blower* Heat exchangers. Office Equipments* Type writer* Duplicator Machine* General Machines Farm MAchines* Thressing Machine* Combine harvesters* Tractors Automobile* Garages for cleaning of all metallic parts & Engine.

Appearance : Clear liquid

Product Description Range of PTFE ring and gasket is manufactured using moulding method with PTEF method with PTEF granular resin. PTFE, compared with other plastics, has a superior properties against chemicals and temperature. The PTFE ring & gasket offered by us is highly acclaimed by all our clients due to their high reliability as well as durability. These ring joint gaskets are especially designed to withstand exceptionally high assembly loads over a small area, thus producing high seating stresses.

Product Description We deal in PTFE Tube and PTFE Pipe in wide range of standard size products and also customized lengths and sizes as per your requirement. PTFE Tubes are known for its characteristic use in high temperatures, chemical resistance and lubricity.

Our gamut of precision industrial products comprises of PTFE Round Bar which include glass filled, carbon filled, bronze filled, liner PTFE, bar, etc. These bar are extensively used in various industrial applications owing to their unique qualitative features such as:

Thickness : 2-6 mm

Length : 300 – 900 mm (standard)

Length : 3000 – 12000 mm

Length : 100 mm (standard) upto 300 mm in special cases.

Length : upto 5000 mm

Product Description Asbestos PTFE packing is made of white asbestos fiber cords impregnated with PTFE dispersion. Soft in texture, this material is suitable for sealing pumps for various chemicals. However, packing impregnated with lubricants is recommended for use with reciprocating pumps or for sealing in places where high linear velocity. Application conditions:

Standard Size : Thickness From 1.5 mm to 100 mm / 300 mm2 / 400 mm2/ 450 mm2 / 500 mm2 / 600 mm2 / 900 mm2 / 1000 mm2/ 1200 mm2 Available Grades : Virgin PTFE 15 % Peek PTFE 15 To 25 % Glass Filled PTFE 25 To 35 % Carbon Filled PTFE 15 % Graphite Filled PTFE 40 to 60 % Bronzed Filled PTFE 5 to 15 % Aluminum Oxide Filled PTFE 5 to 10 % Stainless Steel Filled PTFE 5 to 10 % Mica Filled PTFE 55 % + 5 % Bronzed + Molybdnum Disulphide Filled PTFE 15 % + 5 % Glass + MOS2 Filled PTFE Pigmented PTFE

Product Description Introduction:Flex-O-Seal is a unique sealing material manufactured from special grade of expanded 100% pure PTFE by transforming the fibrous structure by means of a special process. Though very tough, it is spongy and suited to almost all flanges, covers and narrow cavities. Its special soft and flexible character enables it to be the most ideal seal under pressure without significant cold flow even on irregular, badly damaged or corroded flange surfaces. Once bolted this gasket rarely need to be retorqued. Properties: FLEX-O-SEAL recommended temperature-240°C, to 310°C, PH Range 0-14 No deterioration due to stocking for long time. Resistant to high pressure, non-toxic.Not recommended for use against elemental fluorine, alkali metals and strong oxidising agents. Application:FLEX-O-SEAL is safely used in petroleum refinering companies even in their offshore operations, corrosive chemical processing, food processing, paper mill, marine installation, for glass lined or fibre glass reinforced vessels and tank lid sealing, manhole covers, vent pipes, heat exchangers, pumps or compressors housing flanges, valves and many more industrial applications where conventional pre-cut gaskets are not readily available or unsuitable. Installations: The sealing surface must be clean, free from grease and dry to enable the gasket to stick properly. The width of the joint gasket is to be determined by the nominal diameter or type of flange. Selection of a tentative size of joint gasket would be approx, 1/3rd flange contact width inside the bolt hole e.g., 7 mm gasket joint to suit a 20 mm flange width. Remove the protective foil from the adhesive joint gasket to allow for fitting. Stick the gasket approx 2 mm away from the bolt hole and press on lightly. Do not butt the ends overlap them in front of a bolt (see fig. 1) Tighten the lubricated bolts in opposite pairs. Since it is highly compressible only bolt pressure is required to seal. The lap joint deforms perfectly to give a reliable seal. For delicate components such as glass flanges the gasket ends can be joined by cutting a step in each end of gasket. FLEX-O-SEAL is easy to install, able to fill severe surface irregularities and reduces inventory of ready made gaskets, envelopes, etc. It has therefore taken its name as UNIVERSAL JOINT GASKET. On irregular or damaged flanged surfaces, it is possible to build up with short length of FLEX-O-SEAL.

Product Description Type: Line; for Flanges Valve; with Spindle Stirrer Used mainly in chemical process pipelines and chemical manufacturing equipment.

Product Description PTFE Bellows for Lined Pipes Bellows are specially designed form virgin PTFE and is contour moulded. This manufacturing method guarantess an excellent structure of the material; Symptoms of ageing are practically excluded. Very long term durability and low maintenance costs are assured. These Bellows are manufactured in different sizes form NB 25mm to NB 500mm. The allowable operating pressures are depending on services conditions. The Bellows can be used upto 200°C. Bellows serve for compensation of: Vibration Thermal Strain and Expansion Axial and Redial motion These Bellows are meant for resisting highly corrosive chemicals plants and piping for aggressive medias.These Bellows are installed in PTFE Lined Carbon Steel Piping and equipment without additional gaskets. For use with piping and equipment made of glass, enamels and ceramics we recommend PTFE Gaskets, offered as accessory. The sealing surfaces are covered end plates and individually boxed for protection against mechanical damage. Limit bolts are preset to prevent over extension during operation.

Product Description Features • Sets in 30 minutes (at 27°C)• Can be moulded into different shapes• Cures to a hard mass• Provides rock hard sealing. Can be shaped, drilled, filed, sanded, painted upon 15g, 30g, 50g, 75g, 100g, 250g, 1kg

Product Description Lubricated and graphite general purpose asbestos packing for Glands for medium pressure conditions conforming to IS Specification 4687 & DGS&D Specification. Service Recommendation: Water, Brine Solution, acids / alkalis.Available Sizes: 3 & 5 mm in Spools of 10 M.6 -16 mm in 1 kg Coils 19 mm – 50 mm in 5 kg Coils.

Product Description Features: Graphite gland packing with carbon fiber corner is braided from expanded graphite yarn,which can withstand high temperature and carbon fiber with superior corrosion resistance. The carbon fiber in four corners provides higher resistance to extrusion and attrition. This packing can effectively avoid leakage, especially suitable in application of power station valve with high temperature and pressure. Application conditions:

Features: Gore fiber produced in USA is superior in heat-condution,lubrication, and corrosion resistance.it can emanate attrition heat in high speed. Even the shaft speed is up to 21m/s , the packing won’t turn to be hot ,hard or broken.It’s suitable for application of various pumps and valves. Application conditions:

Product Description Features • Unsurpassed bonding strength• Resistant to water & heat Areas of Application • Plywood to Laminate• Plywood to Veneer• Any Wood to Wood bonding• MDF/Particle board/Block board to laminate 50 G, 125 G, 250 G, 500 G, 1kg, 2kg, 5kg, 10kg, 15kg, 20kg, 30kg, 50kg, 200kg

Product Description Expanded PTFE Sheet Gasket is a Universal sheet gasket material for most services. Seals rough and irregular surfaces.Seals of up to 3000+psi can be achieved depending on the flange type & design and type of media being sealed. this gasket is suitable for temperatures to 600°F. E-PTFE is much softer and more flexible than regular Expanded PTFE Sheet Gasket and thus conforms easily to irregular and rough surfaces.

Product Description Expanded graphite packing is braided from high-grade low sulphur expanded graphite yarn. This item has superior resistance from high temperature and chemical corrosion,as well as other special sealing effects.It’s widely used in steam valves of powder station,,static sealing with high temperature,high pressure and chemical corrosion.Application conditions:1) Max. working temperature:- 200°C ~ +650°C (STEAM)-200 ~ +565 (ATMOSPHERE)2) Max. working pressure: 25 Mpa(can only be used in valve and other static sealing condition)(1)Expanded graphite packing(with carbon fiber,SS wire, inconel wire)pressure:35 Mpa(2)Expanded graphite packing(with inconel jacketed)pressure:40 Mpa

Product Description PTFE Envelope Gasket are two types: Slit Type : It is available in 0.5 mm to 0.5 mm thick or thickness as per customer requirement. Milled Type / “U” Type : It is manufactured and available in 0.5 mm flange & gas, as per customer requirement. Envelope gaskets are also available with Asbestos / Non-asbestos & Steel Filler.