Gem Equipments Ltd Arasur, Coimbatore, Tamil Nadu

The GEM COOLING TOWERS is a pioneering product in Design & manufacture of FRP Cooling towers in South India. We are continuously striving to offer better Cooling solutions to customers, which are both, innovative and also state of the art. ECT is the Evaporative Coil Cooling tower which is an induced draft counter flow design Closed Circuit Cooler.DesignCasingFillSprinklerSCSP NozzlesDrift EliminatorAxial FanMotorsCorrosion FreeLight WeightInstallation, Service & Maintenance

Designed to drain sludge and rust laden condensate in compressor room equipment and pipeline. Work pressure - 16 bar Heat exchanger is fully enclosed. Compact Size. Low power consumption Easy for installation Corrosion resistance painting High Efficiency copper tubes. Optional Vortex Separator for 99.99% moisture removal. Continuous duty motor with Aluminium highly reliable plastic fans. Most suitable for portable applications.

Work pressure - 16 bar Heat exchanger is fully enclosed. Compact Size. Low power consumption Easy for installation Corrosion resistance painting High Efficiency copper tubes. Optional Vortex Separator for 99.99% moisture removal. Continuous duty motor with Aluminium highly reliable plastic fans. Most suitable for portable applications. Dryers are sized according to the flow, pressure, temperature and dew point required of the compressed air. If these conditions are changed, the resulting efficiency of the dryer can be drastically affected. The temperature of the compressed air leaving a compressor varies from 82 °C to 177 °C, depending on the type of compressor, it is essential that an After Cooler be installed upstream of most dryers because it will lower the temperature to required level and will remove 50 to 75% of water vapour contained in the air. After coolers are available in either air or water cooled units.

Compact designWall mounting typeEco friendly systemConsistent dew pointLow pressure dropPower savingCopper "Tube in Tube" non corrosive heat exchanger.Inbuilt Non Corrosive Centrifugal specially treated Aluminium Moisture Separator.PUF Insulation for Heat Exchanger Assembly.Timer based Zero air loss Auto Drain Valve.Filled with "Ozone Friendly" R134a refrigerant.Wall Mounting type - can be mounted on any machine tool.Noiseless operation.

Designed as per IS7938Hand and man holesWorking pressure upto 40 barShell Dish as per ASME Sec VIII and IS2825Store compressed air.Condense and trap the moisture in the compressed air and to let the impurities settle down before air passes into the piping.Equalise pressure variations in the pipe.Prevent short cycle loading and unloading of the compressor. Gem air receiver are dimensioned to suit the compressor flow rate, the regulating system, the working pressure and the expected variations in the air consumption.

Compact DesignLow Pressure DropConsistent Dew PointPower SavingHigh Quality FinishingNon-cyclic SystemMore ReliabilityEase of InstallationEnvironment FriendlyReduced Maintenance

Moisture Separators is designed to provide 99% effective moisture separation. All air contains moisture in the form of water vapour.

All air contains moisture in the form of water vapour. This water vapour begins to condense into condensate in the compressed air system when the air cools to saturation point. When this compressed air is used in the manufacturing plant, the moisture causes problems such as washing away of lubricants, increasing wear and tear, rust formation, corrosion etc. The easiest and permanent solution for moisture removal problem is the provision of

The industrial chillers we offer are built in closed stainless steel tanks. The rigid steel frame construction has a power coating finish and hence is weather resistant. It is designed to maximise exchanger efficiency. The heat exchanger is of coaxial type and uses copper tubes in a coiled tube in tube arrangement. This arrangement maximises heat transfer rate with minimum pressure drop. To further increase heat transfer efficiency, a counter flow pattern is used that achieves maximum

The industrial chillers we offer are built in closed stainless steel tanks. The rigid steel frame construction has a power coating finish and hence is weather resistant. It is designed to maximise exchanger efficiency. The heat exchanger is of coaxial type and uses copper tubes in a coiled tube in tube arrangement. This arrangement maximises heat transfer rate with minimum pressure drop. To further increase heat transfer efficiency, a counter flow pattern is used that achieves maximum temperature difference.

Compact DesignLow Pressure DropConsistent Dew PointPower SavingHigh Quality FinishingNon-cyclic SystemMore ReliabilityEase of InstallationEnvironment FriendlyReduced Maintenance

Work pressure - 16 bar Heat exchanger is fully enclosed. Compact Size. Low power consumption Easy for installation Corrosion resistance painting High Efficiency copper tubes. Optional Vortex Separator for 99.99% moisture removal. Continuous duty motor with Aluminium highly reliable plastic fans. Most suitable for portable applications.

The industrial chillers we offer are built in closed stainless steel tanks. The rigid steel frame construction has a power coating finish and hence is weather resistant. It is designed to maximise exchanger efficiency. The heat exchanger is of coaxial type and uses copper tubes in a coiled tube in tube arrangement. This arrangement maximises heat transfer rate with minimum pressure drop. To further increase heat transfer efficiency, a counter flow pattern is used that achieves maximum temperature difference.

Can be offered for higher pressure and lower dew points also.Power on light.On - Off switchTower pressure guagesHighly accurate motorized cam timer.Differential pressure guage for filters.*PLC*Cycle failure indication*Sized to save heat of adsorption - minimizes purge air usage.Limited velocities through tower prevent bed fluidization - stops desiccant dusting.Large desiccant bed - ensures sufficient contact time to produce -40° C Dew point(-80°C Dew point with Molecular sieves)

The GEM COOLING TOWERS is a pioneering product in Design & manufacture of FRP Cooling towers in South India. We are continuously striving to offer better Cooling solutions to customers, which are both, innovative and also state of the art. ECT is the Evaporative Coil Cooling tower which is an induced draft counter flow design Closed Circuit Cooler.

The main function of the offered dry cooling tower is to cool and maintain the temperature of process hot water at a particular level.

DesignCasingFillSprinklerSCSP NozzlesDrift EliminatorAxial FanMotorsCorrosion FreeLight WeightInstallation, Service & Maintenance

Work pressure - 16 bar Heat exchanger is fully enclosed. Compact Size. Low power consumption Easy for installation Corrosion resistance painting High Efficiency copper tubes. Optional Vortex Separator for 99.99% moisture removal. Continuous duty motor with Aluminium highly reliable plastic fans. Most suitable for portable applications.

Designed to drain sludge and rust laden condensate in compressor room equipment and pipeline. Zero Air LossNo Electricity and NoiseRobust DesignManual DischargeCleanable OrificeFloat type The offered product is designed to drain sludge and rust laden condensate in compressor room equipment and pipeline. The digital electronic circuitry is encapsulated in high-grade resin for absolute time control. The valve comes with settings which gives the power and drain status indicator. It also has a waterproof IP 55 enclosure for suitable outdoor installations.

The main function of the offered dry cooling tower is to cool and maintain the temperature of process hot water at a particular level. The tower works on a principle of heat transfer and is driven by an electric motor. The wound copper tubes eliminate any unnecessary leakage after installation. The tubes also allow better heat transfer efficiency.

The main function of the offered dry cooling tower is to cool and maintain the temperature of process hot water at a particular level. The tower works on a principle of heat transfer and is driven by an electric motor. The wound copper tubes eliminate any unnecessary leakage after installation. The tubes also allow better heat transfer efficiency. The positive and controlled expansion between the tube and fin provides a clean, smooth inner tube surface for water pressure drop and guarantees uniform heat transfer. The rigid galvanized steel frame provides protection against tube damage during expansion and installation. Also, it is mounted on a heavy duty channel base frame. The axial flow fans are noise-free. The low speed of the motor minimises noise and increases efficiency. Motors are specially designed to withstand moisture, rain and dust.

We are offering desiccant air dryers with Tower pressure guages,Highly accurate motorized cam timer.

The GEM COOLING TOWERS is a pioneering product in Design & manufacture of FRP Cooling towers in South India. We are continuously striving to offer better Cooling solutions to customers, which are both, innovative and also state of the art. ECT is the Evaporative Coil Cooling tower which is an induced draft counter flow design Closed Circuit Cooler.

DesignCasingFillSprinklerSCSP NozzlesDrift EliminatorAxial FanMotorsCorrosion FreeLight WeightInstallation, Service & Maintenance