International Equipments Kanjurmarg East, Mumbai, Maharashtra

Universal Testing Machine    Highly accurate position control with high range of speed Accurate start and stop instanatly using 32 bit microcontroller Four line and 20 characters controller with multiple features Automatic calculation of modulus @different strains selectable Multi unit display in Kg, pound, Newton mm, cm, inch selectable Direct display on controller and numeric printout facility Safety norms of over load in auto as well as manual mode Safety norms of over travel in auto mode. Tests preprogramming facility for Tensile, Flexural, Peel, Bond, Compression, Cyclic endurance based on load, travel, time Data lock for calibration and master controlled parameters

Specification:Double Walled well insulated tank with proper insulation for the doors also. Offered capacity: From 200 litres to 5000 litres capacity.Stainless steel manifolds placed in the walls of the tank having quick release couplingsInside and out for easy handling of hoses coming from panel outside and going to the pipePaint : Powder coated Power : 415 volts , three phase

  tensile testing is a most significant and popular test procedure which is performed in different production verticals to measure the elongation strength and durability of the products. Tensile testing is also known as tension testing, this test shows at what point sample fails when an extensive amount of tensile force is applied to the sample. It helps the engineers to measure the maximum force a material can tolerate to its maximum before it brakes and helps to decide the suitability of the material for a particular application.the tensile test is performed using a high-quality testing machine known as tensile tester or tensile testing machine to determine properties of tensile and elongation as per astm d - 638 / astm d – 882 of plastics – eco version. specification: load capacity : up to 500 kg*.no. Of load cell : one. cross travel : up to 1000mm*.speed : variable between 10mm/minute to 500mm/minute. paint : powder coated. power : 230 volts, 50hz, single phase.direct display through microcontroller : peak load, area and tensile strength at peak load.

Specification:Temperature Controller: Digital PID Controller with range up to 300°C, Resolutionof 0.1°C & accuracy of +0.5°C. Pan: 500 Nos. of aluminium pans with 40 mesh screen in SS 316 will be provided as per DOT specification. Gas Flow Control: Gas Regulators & Rotometers will be supplied for Nitrogen & Oxygen Gas respectively. Indium material will be supplied for Calibration of temperature.PRINTOUTS THROUGH PC: The display & printout of Delta Temperature Vs Time graph along with Oxidation Induction Time result is Possible through your PC. The printout includes Party’s Name, address, file name, date, batch no, Operator name, Sample weight, Set temperature, Start time, Finish time, Gas flow rate etc.Calibration graph of melting point of indium metal along with printout facility is provided as per DOT Specification. Cooling System: Cooling of barrel by water is provided.

for making ‘V’ notch in the Izod / Charpy samples as per ASTM D – 256. Specification: Depth micrometer : “Mitutoyo” make. Range : 0 – 25mm with least count of 0.01mm. Cutting angle : 45º.Paint : Powder coated.Power : 230 Volts, 50Hz, single phase.

Charpy impact tester is manufactured as per ASTM D 6110 and ISO standard. These models are used by injection moulds & engineering plastic manufacturers. Also charpy impact tester has wide importance in testing polypropylene pipe manufacturing industry for testing the PPR pipe. Notch cutter is a requirement for making notch on charpy impact samples. Thus notch cutter is also supplied along with this equipment. Charpy impact tester and Izod impact tester are those material testing equipment that are used to check the axial impact on molecular structure of material and thus measure the failure of polymers under impact. condition.  Specification:  Capacity : Up to 25.00 Joules.Release angle of pendulum: 150 degree.Range of four scales : 0-2.71 Joules, 0-5.42 Joules, 0-10.84 Joules, 0-21.68 Joules and 0-25.00 Joules.Minimum resolution on scale: 0.02 Joule, 0.05 Joule,0.1 Joule, 0.2 Joule and 0.2 Joule respectively. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase. Direct display through microcontroller: Impact strength in joules/meter and kg-cm/cm.Graphic display and printout through PC: Impact energy Vs Angular displacement graph and numeric reports consisting of values for impact strength as per ASTM standard, ISO and IS standard in different units could be obtained by attaching a printer to the PC.  

as per Tappy T – 815 standard to determine the coefficients of friction between film to film, film to metal and film to glass. Specification: Speed : 1.5º to 2.0º / second.Weight of the sled: 750 grams. Size of sled : 4 inch X 2 inch. Accessories : 2 nos. of S.S templates. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase.

for pipes as per IS 4985 and IS 12235 (Part 9) to test the impact strength of the pipes. Specification: Height of fall : 500mm, 1000mm and 2000mm.Weight of striker : 250 grams, 500 grams and 1000 grams. Material of striker : S.SAngle of ‘V’ block: 120º.Release mechanism of striker : Manual. Paint: Powder coated.

as per IS 4984 and IS 4985 to check the creep rupture of pipe when subjected to internal pressure under a specified condition.Pressure range : 0 – 100 bar*.No. of stations : 8 nos. Pressure input : Through compressed air having pressure upto 5 kg/cm.sqPressure output: through hydro-pneumatic pump.Time range : 0 – 999.9 hours. Panel mounting : Trolley with castor wheels. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase.Direct display through MMI :Set pressure, Actual pressure, Set time, Actual time, Set temperature and Actual temperature.Graphic display and printout through PC :In addition to the above values Pressure & Temperature Vs Time graph could be obtained for any station by attaching a printer to the PC.

to cut samples having thickness up to 4mm. Specification : Capacity : 5 tonnes*. Operation : Manual. Horizontal day light : 12 inch. Cross travel : 4 inch. Paint : Powder coated. 

Temperature zone: Two. Controller: Auto tuned PID controller with temperature range up to 200 deg C havingresolution of 0.1 degree centigrade. Clamping Jaws: One fixed and second movable by pneumatic action.Day light: 50 mm.Sealing dimensions: Length 150 mm x Width 20 mm. Mounting: Table top. Power requirement: 230 Volts, 60 Hz, Single phase – 15 ampere.

as per astm d - 1693 to determine environmental stress cracking of ethylene plastics. specification: temperature range : from ambient to 200ºc. no. Of stations : six. material of construction : inner bath: s.s                                    outer body: m.saccessories : cutting die, nicking jig, bending cum transfer tool and aluminium foil – 1no.each, specimen holder, test tube and rubber cork – 6 nos. Each. paint : powder coated. power : 230volts, 50hz, single phase.

for conditioning of pipes for impact test as per IS 4984 and IS 12235 (Part 9). Specification: Size of the working chamber : 16 inch X 16 inch X 16 inch*. Material of construction : Inner bath : S.S                                    Outer Body : M.STemperature range : Ambient to 0ºC.Compressor : CFC free. Paint : Powder coated. Power : 230 Volts, 50 Hz, single phase.

to check the adhesive strength between two samples. Specification:Load capacity : Up to 5 kg.*No. of load cell: One. Cross Travel : Up to 250 mm*Speed : 300 mm/minute. Direct display : Peak load. Paint : Powder coated. Power : 230 Volts, 50 Hz, single phase.

to check the opaqueness of plastic samples as per IS 4985 and IS 12235 (Part 3). Specification: Range : 0 – 99.9 % opaque. Direct display : % opaque. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase.

Specification: Size of the working chamber : 4 inch X 4 inch X 9 inch*Material of construction : M.S Temperature range : Ambient to 1150ºCPaint : Powder coated. Power : 230 Volts, 50Hz, single phase. 

with radial air circulation and auto shut facility. Specification: Size of working chamber : 12 inch X 12 inch X 12 inch*.Material of construction : M.S. Temperature range : Ambient to 250ºC. Air circulation : Radial fan (It saves power at least 20% by re-circulating the same hot air inside the oven). Timer : Digital presettable with range upto 999 minutes. Paint : Powder coated. Power supply : 230 Volts, 50Hz, single phase.

International equipments developed the first dart impact tester way back in year 1971 as per the ASTM D 1709 and IS 2508 standard. This equipment is mainly designed to check the impact failure weight of film and sheeting by a falling weight impact method.       ENLARGE VIEW In addition to dart impact tester other equipment such as coefficient of friction, tensile tester, heat sealer, opacity tester, melt flow index tester, peel bond tester are also offered by international equipments Specification:Dart : 2 nos. Weights : A set of weights ranging from 5 grams to 500 grams would be supplied for incremental loads. Release mechanism : Electromagnetic. Vacuum creation : Single stage oil vacuum pump. Paint : Powder coated. Power : 230 Volts, 50 Hz, single phase.

FOR CUTTING SPECIMEN UP TO 50 MM THICKNESS OFFERED ALONG WITH CUTTING TEMPLATES AS PER ASTM / ISO STANDARDSSpecification: Diameter of the cutter: 15 mm. Material of cutter: carbide.Speed of cutting: Adjustable through AC variable drive.Minimum & maximum dimensions of specimen: 5 mm to 25 mm One number of Template for ASTM D 638 Type I for tensile would be included in the supply with this equipment. Additional vacuum system will be provided for collection of waste material during test. Power supply: 230 ± 5 Volts AC, 60Hz, Single phase.

As per ASTM D 1238 & ISO 1133 – (Test Method A & B) to check the melt flow rate (MFR) & melt volume rate (MVR) of thermoplastics and compounds with automatic result. Specification: Microcontroller with alpha numeric key pad having built-in temperature controller with temperature range up to 400 degree centigrade, resolution of 0.1 degree Centigrade and accuracy of +/- 0.1 degree Centigrade similarly built-in timer with range 999.9 seconds. Piston Travel: Up to 25 mm & resolution of 0.02 mm. Specimen cutting: Motorized. Specimen Weighing: Automatic up to 60 gm and resolution of 1 mg. Weight: 0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg & 21.6 kg hard chrome plated weights. Digital Display: Individual MFI, MVR, Melt Density results & average results. PC output: Through serial port with Window 7 compatible software. Accessories: Standard accessories*. Paint: Powder Coated. Power Supply: 230 Volts, 50 Hz, Single Phase.  

as per ASTM D – 1525 and ASTM D - 648 to determine vicat softening temperature and heatdeflection temperature of plastics.Specification:  Temperature range : From ambient to 300ºC. No of stations : Three. Material of construction : Inner bath: S.S                                    Outer body: M.SRate of heating : 120ºC / hour and 50ºC / hour. Sensor : Range upto 10mm with resolution of 0.01mm. Weights : A set of weights ranging from 5grams to 2000grams would be supplied for incrementalloads. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase. Graphic display and printout through PC:Penetration/Deflection Vs Temperature graph and numeric reports consisting values of vicat softening temperature and heat deflection temperature could be obtained by attaching a printer to the PC.

to determine the effect of relative humidity on sample at various temperatures. Computerised Humidity chamber to determine the effect of relative humidity on sample at various temperatures. Specification: Size of the working chamber : 18 inch X 18 inch x 24 inch*Material of construction : Inner bath: S.S                                    Outer body: M.SHumidity range : 20% RH to 95% RH. Temperature range : 10ºC to 85ºCCompressor : CFC free. Direct display and printout through microcontroller : Set RH, Actual RH, Set temperature and Actual temperature. Graphic display and printout through PC: In addition to the above values, % RH and Temperature Vs Time graph could be obtained by attaching a printer to the PC.Paint : Powder coated. Power : 230 Volts, 50 Hz, Single phase.  

as per ASTM D 1603, IS 4984 and IS 2530 to determine carbon black content of plastics.Specification: Size of furnace : 10 inch x 8 inch x 8 inch.Material of construction: M.S.Temperature range : Ambient to 1150 ºC Accessories : Desiccator, Glass U tube, Combustion tube, Combustion boat, Rotometer, Rubber tube [1 no. each], Glass end caps – 2 nos. and Glass traps – 3 nos.Paint : Powder coated.Power : 230 V 50Hz, single phase.