Krutam Technosolutions Pvt. Ltd. Makarpura, Vadodara, Gujarat

The Webster Hardness Testers are a portable, fast, accurate hardness gauge that are made in three distinct models for testing Aluminum, Brass, Copper and Mild Steel. Webster Hardness Testers will quickly identify tempers and test a variety of shapes that other testers cannot check, such as extrusions, tubing and flat stock. All testers operate in the same manner but differ only in penetrator design, type of load spring and hardness ranges. The principle of operation is simple. The work to be tested is placed between the anvil and the penetrator. Pressure is then applied to the handles until "bottom" is felt at which time the dial indicator is read.   Model B The Model B Tester is designed to cover the hardness of aluminum alloys from the 100 to the 7075 series. The 20 graduations on the Webster dial indicator covers the range between 25 and 110 on the Rockwell E Scale. Model B-75 The Model B- 75 Tester was developed to obtain more sensitive response to slight changes in the upper range of hardness covered by the Model B. This sensitivity is particularly useful in testing mild steel and the stronger aluminum alloys. For brass the B-75 covers the range from annealed to full-hard. This added sensitivity is accomplished by incorporating a penetrator of slightly different contour and a heavier load spring than used in the Model B. The 20 graduations on the Webster dial indicator covers the range between 20 and 100 on the Rockwell B Scale.   Model BB-75 The Model BB-75 Tester was developed to answer the need of certain industries for a method of rapidly testing the hardness of electro-deposited copper in the low hardness range. The B-75 penetrator is used to give sensitivity, and the Model B load spring is employed to give light pressures. This combination allows the user to test the soft range of many common materials. The graph below shows the range covered by the Model BB-75 tester on copper.   Applications and Features Applications for Webster Hardness Testers are: Identifies heat-treated from nonheat-treated parts. Provides correlation between a bench mounted hardness tester and the production line. Segregates materials in stock. Differentiates between soft or work-hardened material. Identifies parts made from improper or substandard alloys. Checks for proper heat-treatment response. Useful in conjunction with stationary laboratory hardness testers. Gives a rapid 100% check on parts which would consume many man hours with slower operating test equipment. Can be used on assemblies that cannot be brought to the labs. Webster Hardness Testers Feature: One hand operation and portability. Round 3/8 inch diameter anvil permits testing a great variety of shapes. Simple operation permits readings independent of the operator's skill. Test is made by simply applying pressure to the handles until "bottom" is felt. Easy-to-read dial indicator with 20 graduations permits use of the tester as "go" and "no-go" gauge. Standard hardness gauge tests materials up to 1/4 inch in thickness. Increased capacities available up to 1 inch.

Vickers Cum Brinell Hardness Testing Machines ( Model : BV ) Suitable for finding out Vickers / Brinell hardness of metals from soft to very hard. Push button control for load selection. A range of test loads for Vickers / Brinell - from 1 kg to 250 kg. Optical Magnifications - 35X, 70X & 140X available. A precision Diamond Indentor (136° pyramid) is used to make sharp indentations on the specimens / samples. Maximum Test height x Throat : 250 x 150 mm. Load accuracy well within ±1% of nominal load value. Machine conforms to IS:1754. Computerized model is available .Computerized model has built in CCD and suitable advanced software. Hardness will be displayed on computer monitor automatically. Results printout can be taken.  

Model 300TE Screen Glass screen - Glass screen Ø 400mm with crosslines   Magnification 5x,10x,20x,50x,100x Telecentric Lenses   Workstage Size of Top Plate - 350mm x 210mm Measuring Traverse - X:200mm, Y: 100mm Working Area - 205mm x 105mm Load Capacity - 20 kgs Max Diameter - 150mm Digital Measuring Systems Linear - 3 axis DRO with Linear Encoders 0.005mm LC Angular - 360º rotary encoder LC of 1' of an arc. With digital display Tungsten Halogen lamps Illumination Systems Profile - 24V, 150W Surface Illumination - 24V, 150W - 2 Nos Weight 100 kg ( Unpacked)   Dim (LxWxH) 700 x 480 x 1025

Dynamic Balancing Machines- Vertical Type ( Model : FVBM ) Vertical type hard bearing machines for single plane balancing of rotors like clutch plates, fan blades, fly wheels, magnetos, grinding wheels, impellers, pulleys, etc. Microprocessor based measuring panel with auto compensation facility. Minimum achievable unbalance upto 0.5 micron shift in c.g. Various Models - Suitable for rotors from 0.3 kg to 300 kg. Computerized / Electronic versions with printer facility & as per customers requirements can also be supplied.

DIGITAL USB MICROSCOPE having electronic imaging system. It can be used for education, training, beauty care, industrial inspection, general investigation & in field work. The Microscope brings unprecedented flexibility and excitement to the learning process. Enabled easy handling for "Touch & View" microscopy, equipped with 330K resolution 1/4" Color CCD & USB Interface Plug, operating at 400mA with a lighting lens unit. Weight 200gms., including lens unit.Recommended Windows and Macintosh environment.

Variety of tests like Tension,Compression,Tranverse, etc. are conducted. Continuous roll autographic "Load Vs Elongation" recorder. Suitable for testing a wide range of metallic materials. Extra (Optional) Accessories such as - Mechanical Extensometer, Load-Stabilizer, Attachments for Brinell test, Tensile test for shouldered & threaded, Single & Double shear test, Bolts-Nuts & Washer test, Rope test, Flat Belt test, Bend-Rebend test, 180° Bend test, Pull-Out test, etc. are available. Capacities from 100 kN to 2000 kN. Various Analogue Models - TUN-100, TUN-200, TUN-400, TUN-600, TUN-1000 & TUN-2000. Loading accuracy well within ±1%, conforms to IS:1828 / BS:1610.

This DIN Rail mounting instrument is highly useful far controlling over current in any process industries. With use of C.T. any current range is feasible for controlling. Instrument works ok with under current limit and trips if current exceeds the set limit.   Application OEM Equipment in control panel of process industries. Works as over current limiter. Economical priced for panel instrument.

Model: Bl-100 & Bl-100f Features Bulb with Koop glass filter for eye protection Built-in silent fan for cooling

Application This Machine applies a torque on the specimen held in its chuck and measures the twist. The machine is useful for material manufacturers, Research Institutions, Testing Laboratories, Educational Institution etc. to test metals.   Models FTT-100, 200, 500, 1000, 2000 Nm (Capacity ranging from 100 Nm to 2000 Nm)   Accuracy & Calibration Every machine has the accuracy of 1% of the true torque and calibrated according to standards set by IS, BS, ASTM, etc.   Salient Features Suitable for Torsion and Twist test on various metal rods and flats. Torque measured by pendulum dynamometer system. Geared motor to apply torque to specimen through gear box. Set of jaws to accommodate different size and diameter of test specimens provided. Computerised torsion testing machine is also available.

Variety of tests like Tension, Compression, Cross breaking / Bending, Shear, Linear Bonding / Gripping / Peeling strength of adhesives & tapes, etc. are conducted. Suitable for testing a wide range of materials like rubber, wood, plywood, plastic, rexins, ceramics, teflon, cardboard, latex, composites, ferrous metals, non-ferrous metals,etc. of various forms like round, flat, thread, wires, dumbells, fabric, belts, strips, ropes, etc. Wide range of Grips, Attachments & Special fixtures are available to suit variety of material and shapes. Continuous roll autographic "Load Vs Elongation" recorder. Elongation scale with least count 1 mm. Three measuring ranges for accurate testing. A number of straining speeds are available for proper selection. Machine with AC or DC drive motor is available. Various Models - Maximum Capacity from 200 N to 50 kN. Loading accuracy well within ±1%, conforms to IS:1828 / BS:1610. Hand operated cutting press with different sizes dies are available for cutting dumbbell specimen.

TH measures minimum, maximum and real time values of room temperature and humidity. TH also displays time in hours and minutes in 12 and 24 hours formats.Facility of daily alarm, alarm off and memory daily reset on/off are provided.

Model RSM-4 Observation Head Binocular head inclined at 45-deg., rotated through 360-deg with adjustable inter-pupillary distance. Focussing By Rack and Pinion mechanism with adjustable tension collar. Magnification Standard magnification 20X & 40X with flat field. Illumination With integral illuminator, 2 lamps are fitted to provide both transmitted and incident illumintation. Objectives 2 sets of objectives 2X and 4X, selected by rotating nosepiece through 90-degrees. Eyepieces Standard extra wide field eyepieces WF-10X is provided. Optional WF-15X & WF-20X.

Body Monocular Fixed Straight Tube, length 160mm. Nosepiece Triple revolving nosepiece with accurate centering and positiveclick stops Stage Detachable Mechanical stage for X-Y cross movement 50X75mm, fullygraduated vernier scale. Illumination 20W halogen lamp, 220/110Volts. Lamp slots provided for naturalcooling of the illuminator. Objectives Achromatic 4X - 10X- 40XSL. Eyepieces Huygenian 10X and 15X Screen 150mm diameter Glass Projection Screen is provided, can be rotatedover 360-degrees on Microscope tube. Model PRM-11 All specifications are as per PRM-11A but has only 2 Objectives10X & 40X. Screen size 100mm and without mechanical stage.

Eyepieces : Huygenian 5X-10X-15X (any two) or Wide field 10X.

Small & compact machine with high accuracy for balancing of small rotors like textile spindles, electric power tool armature, etc. Special electro dynamic pickups are used for sensing minute vibration due to imbalance in the rotor. Machine is provided with electronic measuring control panel with digital panel meter for amount indication & xenon flash tube with brilliam white light for locating position of unbalance. Rotor loading and unloading is very easy, as a special quality stretchable rubber belt is used for driving the rotor under trial. Machine is very sensitive & accuracies of the order of 0.2 micron. Machine does not require any concrete foundation. It can be operated by placing on a plain surface. Machine requires single phase supply of 220 volts, A.C., 50 Hz. As such machine can be conveniently located where single phase supply is available. Operation of the machine is very simple and does not requires any skilled operator, once proper training for operating the machine is given. Suitable for rotors from 0.1 kg to 3 kg. Balancing speed range is 800 to 3000 rpm

Brand Name : Krutam

tate-of-the-art imported glass optics. Overhead as well as substage illumination using 20 W quartz halogen bulbs. Illumination can be optimised using electronic controller. Ideal inspection instrument for QC personnel, electronics and precision parts manufacturers, geologists, gemologists etc. Also very useful for micro assembly/repair work. Provides both 20 X and 40 X Magnifications.

Specially designed imported glass optics meant for applications where detailed work has to be done for a long duration at a comfortable distance (340 mm) using fine tools, such as in micro-surgery and micro-assembly. The stereoscopic view enables excellent depth perception and fine manual co-ordination.

Magnification : 2.5 X

Handy table top magnifier, useful for magnifying printed matter, films, artworks, maps etc. Elegantly designed stand.Magnification : 2.5 X

Starting from 1GHz up to 26.5GHz, Tracking generator and various measurement facilities. LISNs, EMI software, EMI analyzers, RF Probes, Antennas. Spectrum Analyzer HM5510 1 GHz Spectrum Analyzer HM5014-2 1 GHz Spectrum Analyzer with tracking generator HM5530 3 GHz Sprectrum Analyzer EMI/EMC Solution EMCIS EMI Analyzer EA-2100 EMCIS Filer Analyzer FA-2000 EMCIS Filer Analyzer FA-2100 EMCIS EMI Spectrum Analyzer ESA-2000 Hameg Line Impedance Stabilization Network HM 6050-2 EMCIS Line Impedance Stabilization Network LN2-16 EMCIS Line Impedance Stabilization Network LN-20 EMCIS Line Impedance Stabilization Network LN4-50/100 EMCIS Power Line Filter LF1-16A EMCIS Shielded Chamber HZ 530 EMV Near Field Probe set upto 1 GHz EMCIS DC Bias Source

Specific Gravity Balance direct reading type for use on vulcanized rubber or such other elastomers. The balance consists of rigid quadrant scale with figures printed on the scale standing vertically fitted on a heavy base. The balance is calibrated from 0.9 to 3.0. For most elastomers the specific gravity lies between 0.9 - 2.0, and test results in this range can be read directly and accurately by two decimal places. The balance is supplied with glass baker & calibration weight for periodical checking.

Measures minimum, maximum and real time values of sound levels (noise levels). Maximum hold updating and display facility is also provided. In maximum hold updating mode, previous maximum value of the sound is displayed and the same remains unchanged until a higher value is detected. Choice of A and C weighting modes is provided. In A weighting mode, -8928 response matches the frequency spectrum of the human ear. A weighting response is useful for OSHA regulatory testing, environmental measurements, work place design, low enforcements etc. In C weighting mode, -8928 response matches the flat frequency spectrum with no increase or decrease of amplitude over the frequency spectrum. C weighting response is useful for sound level analysis of engines and machinery. Fast and slow response modes are provided to suit different applications and standards. RANGE, RESOLUTION AND ACCURACY 40dB to 130dB in 4 ranges of 40dB to 70dB, 60dB to 90dB, 80dB to 110dB, 100dB to 130dB. Choice of manual or automatic range selection is available. Resolution of dB measurement is 0.1dB. Accuracy is within ± 2dB.