Pneum Systems Inc Marol, Mumbai, Maharashtra

These are either horizontal or vertical installations depending upon the space availability. the sizes may vary from 100 liters to 10 Meter cube. On horizontal receivers the compressor and motor can be mounted to save the space of operation.

Capacity : 500 liters

Ever since our inception in this industry, we have been involved in offering excellent quality products. Our entire range of products are manufactured as per international industry standards. Further due to their superior quality these products are widely used in various industries.

PNEUM SYSTEMS INC, has developed Heatless Air Dryer which is a chemical desiccant using dryer, working on adsorption principle. The system consists of twin towers filled with desiccant of appropriate quality and quantity. Wet compressed air after being filtered by the prefilter and coalescing oil filter enters the distribution valve. An electrically operated valve with built in passages, which directs the air to one tower. The air is then passed through the tower and comes out in dry condition. The air is then passed through after filter to remove any carry over dust, via non-return valve. There is a by-pass arrangement with an orifice, to allow a fraction of dry compressed air to expand and pass through the other tower, here by regenerating it and making it ready for adsorption Cycle. The Regenerating air is passed out to the Atmosphere via muffler. At a preset time, the sequence control timer actuates the Distributor valve to reverse the tower function . For lower capacities, the distribution valve and control valve are integral units, however for higher capacity these control elements comprise of discrete control valves and orifices. Our Heatless air dryers are compact, economical, pre assembled, fully automatic, “Fit and Forget” type of units with very little power consumption of around 100 watts. For detailed offer, please indicate capacity, pressure, and source of compressed air.   Features of our Heatless air dryers :1. Outlet air dew point - 40°C is achieved.2. Controlled effluent gas temperature3. Since the drier size depends only on flow and pressure, inlet temp. of 10ºC to 50ºC can be handled by same unit.4. Very low spare parts inventory.5. Desiccant beds can remove oil in its vapour form.

Compressed Air is an important energy source in modern factories because it is flexible and safe but it is only fully efficient when it is clean.

Ever since our inception in this industry, we have been involved in offering excellent quality products. Our entire range of products are manufactured as per international industry standards. Further due to their superior quality these products are widely used in various industries.

Ever since our inception in this industry, we have been involved in offering excellent quality products. Our entire range of products are manufactured as per international industry standards. Further due to their superior quality these products are widely used in various industries.

These are either horizontal or vertical installations depending upon the space availability. the sizes may vary from 100 liters to 10 Meter cube. On horizontal receivers the compressor and motor can be mounted to save the space of operation. Compressors upto 20HP can be suitably mounted on the horizontal tanks upto 500 liters capacity.   Construction : All receivers are made from carbon steel and built to IS-2825 or ASME code section VIII. The working pressures may vary from 75 psig (5kg/square cm) to 750 psig (50kg/square cm). Vessels can be manufactured as per other codes if required.   Each Vessel is fitted with a pressure relief value, a pressure gauge, a drain valve, air inlet and air outlet connections for pressure switch and other safety fittings can be supplied on request. Each vessel is hydrostatically tested as per the relevant code. Other non destructive testing like radiography, Ultrasonic test etc. can be provided if required.

The unit is a shell and tube heat exchange with M.S. shell and Copper tubes. In case of Horizontal after cooler the water passes through shell over the tubes carring hot compressed air. There is a moisture separator provided at the out let of the cooler which removes the oil and water droplets formed due to cooling.

The system consists of twin towers filled with desiccant of appropriate quality and quantity. Wet compressed air after being filtered by the prefilter and coalescing oil filter enters the distribution valve. An electrically operated valve with built in passages, which directs the air to one tower. The air is then passed through the tower and comes out in dry condition. The air is then passed through after filter to remove any carry over dust, via non-return valve. There is a by-pass arrangement with an orifice, to allow a fraction of dry compressed air to expand and pass through the other tower, here by regenerating it and making it ready for adsorption Cycle. The Regenerating air is passed out to the Atmosphere via muffler. At a preset time, the sequence control timer actuates the Distributor valve to reverse the tower function .

PNEUM SYSTEMS INC, has developed Heatless Air Dryer which is a chemical desiccant using dryer, working on adsorption principle. The system consists of twin towers filled with desiccant of appropriate quality and quantity. Wet compressed air after being filtered by the prefilter and coalescing oil filter enters the distribution valve. An electrically operated valve with built in passages, which directs the air to one tower. The air is then passed through the tower and comes out in dry condition.