Wall Form Panel
Wall formwork is perfect for weighty and light duty versatile formwork and is appropriate for vast kind of cast – in situ concrete construction such as walls, adequately stiffened with longitudinal stiffener, foundation, Rectangular or circular tanks, Dams, Bridges, beams, column, etc. Made out of 12G10G, MS sheet with 45mm 50mm deep Angle frame.
...moreTelescopic Span
POLY – TECH Telescopic span is outcome of a lot of years of knowledge in building industry. Their capacity to add in different length modification.
Size : ESO-ESI,SO-ESI,SO-SI
...moreTelescopic Prop
POLY – TECH telescopic prop are mainly ideal and inexpensive process of hold for all type of formwork to slab, beams, walls and column.
...moreSwivel Coupler
A one portion freight bearing coupler for between any two & scaffold tubes at some through 360° . press from elevated status steel and check for distortion & slip.
...moreRight Angle Coupler
One part load coupler use for involving two scaffold tubes at correct Angle or 90° Pressed form elevated rating steel, check for bend & slip.
...morePallet Fork
H-Frame Scaffolding
Consists of rigid welded border make out of 48.3 OD pipe in two plumb and two horizontals. The frames are connected by scissor (Cross) Braces made out of 25 NB NB pipes via the pin welded on frame and secure in spot care of clips.
...morefloor forms
PLOY-TECH floor are make out of 14G12G press bent sheet and light in heaviness as compare to the conservative centering plate obtainable in the marketplace. PLOY-TECHfloor forms are easygoing weight sufficient rigidity gives excellent concrete finish, cuts labour cost and gives a perfect solution to slab shuttering problems.
...moreDropheads
The quick action drop head supplied complete with nuts and bolts. Is designed to fit on Cuplok scaffolding.They allow infills and beams to be struck re-used after only 3 or 4 days, leaving the support in position for the remainder of of the curing period of the concrete slab.
...moreCuplok Verticals
POLY–TECHVertical are complete out of 40 NB ‘B’ Class tube verify to 1S 11611239 Pair of cups are produce at 500 mm cc, but cups at 1000 mm cc are obtainable in usual size of 3.0 mtr, 2.5 mtr, 2.0 mtr, 1.5 mtr, 1.0 mtr & 0.5 mtr. imperfect sizes can be supplied on demand.
...moreCuplok Horizontal
POLY–TECHHorizontals, make out of 48.3 OD scaffold tube verify by IS 11611239 with fake end blade welded at equally ends to tube and are obtainable in length of 2.5 mtr, 2.0 mtr, 1.8 mtr, 1.5 mtr, 1.25 mtr and 1.0 mtr.
...moreCantilever Frame
This grade is designed for helping the formwork & scaffold at lump limits they are obtainable in two sizes of 1.5 mtr & 1.0 mtr lift. It is situated in cup joints.
...moreBridging Horizontal
The Bridging horizontal is produced to make a working place or stage where a obvious span of above 2.5 mtr to 5.0 mtr is necessary by the chief scaffold run.
...moreBeam Brackets
To hold drop beams, eliminate the requirement of further rows of hold up below the beams, the beam bracket might be situated on uppermost cup joints.
...moreAdjuster Floor Form
PLOY-TECH adjuster floor forms are too the vital part of floor form, which is use to evade imperfect slab formwork, thus eliminate of timber in slab formwork.
...moreAdjustable Fork Head Jack
A weighty duty fork head (U-Head) which provide modification able to 350mm to meet a extensive variety of unreliable height. It is designed to produce considerable bearing places. It has a usual acme thread and obtainable in 32 Ø & 36 Ø.
...moreAdjustable Base Plate
For utilize in rolling ground situation & where it is necessary for building up for elevation variation when used beneath supports. obtainable in 32 Ø & 36 Ø, changeable length of 350 mm & 450 mm with adjustment by way of screw upto 275 mm & 350 mm correspondingly.
...moreDumper
Wooden Drop Beam Support
Cuplock Cantilever Frames
Adjustable Base Jack
Acrow Prop
staircase tower
clipping machine
Be first to Rate
Rate This