Power Operated Chucks
Get Price Quote
Power Chucks are made for Automatice Clamping on modern CNC Machines. They are operated Hydraulic Pneumatic Chucks. Power Chucks are available in 2, 3 & 4 Jaws. Hollow Close Bore Chucks are available with KARAM CHUCKS. We sell SECO, GMT, KITAGAWA, ROHM amke Power Chucks.
Power Operated Finger Chuck
Get Price Quote
We offer power operated finger chuck : gmt has developed specialized power chucks for second operations where radial clamping is not possible. A suitable locator is used to locate the component center. The fingers located in a rod, which has a helical groove ensure that the component is flat against the chuck. This enables loading yet ensures accurate location. Gmt-make hydraulic rotating cylinder is used to move the chuck fingers swings in and clamps the component in a single motion. Actuator pin is located on helical groove for actuating the finger. Fingers during de-clamping lift and swings out for component unloading and loading. The chuck firmly clamps the component without any distortion or surface damage. features : chuck has a locator for locating the component. Power operated twist finger chucks cannot perform without locating the component. Fingers are located in a rod, which has a helical groove. Actuator pin located on helical groove for actuating the finger. Fingers during clamping and de-clamping lift, swings in and out, for component loading and unloading. application : automotive, wheel turning, aerospace, aircraft, commercial vehicles, energy, heavy duty machines, defence production, oil, wind generators.
Best Deals from Power Operated Chucks
POWER OPERATED CHUCK FOR CNC AND LATHE MACHINE
65,000 - 300,000 Per nos
Power Operated High Speed Chucks
Get Price Quote
Power Operated Collet Chucks
Get Price Quote
Power Operated Chucks
Get Price Quote
The chuck is mounted at the front end and the hydraulic Pneumatic cylinder or electro-mechanical actuating device is mounted at the rear end of the headstock spindle of the lathe. The chuck and cylinderactuator are connected to each other by a draw bar on draw pipe. The cylinder is connected to two pressure pipes, eash supplying oil under pressure or compressed air to each of the two chambers of the cylinder. The cylinder piston exerts pull of push force when oil or air is fed to the two chambers of the cylinder via a control valve. in case of Hydraulic Cylinders, a drainpipe is also connected to the cylinder to return the leakage oil to the reservoir. Electro-mechanical actuator has an in-built three phase tapered brake motor, the rotary motion of which is converted into axial motion by a set of planetary gears to push or pull the draw bar pipe at the required operating force. Schematic arrangement of Hydraulic and Pneumatic operation is shown in figures G1 and G2.
Power Operated Chucks
Get Price Quote
The Power Chucks are designed and constructed to hold heavy loads during long operation time, the Chucks effectively convert axially transmitted forces on a job into radial forces at the jaws through the wedges. This conversion of forces, both low and high chucking forces, also the chucks have an internal locking system to ensure jobs so not fly off. The Chuck body is made of forged steel with the guideways specially hardened and then ground to a smooth finish. The wedge side is made of nickel chromium steel and case hardened and all working surfaces are well ground. The base jaws with serrations on top face are also made of nickel chromium steel and case hardened. The Jaws are grounded to perfectly match both the wedge and guideways. The base jaws are guided by deep and wide hardened slots in the Chuck body, to ensure ample load bearing area to withstand resultant clamping forces. for periodic manual lubrication of the sliding surfaces grease nipples have been provided. The reversible hard Jaws have serration at the bottom to match the base Jaws. Hard Jaws of various radii are available to hold a wide range of jobs.
Power Operated Chucks
35,000 Per Piece
Power Operated Collet Chuck
Get Price Quote
power operated lathe chucks
Get Price Quote
power operated lathe chucks, hand operated lathe chucks, Lathe Chucks
cnc power operated chuck
Get Price Quote
cnc power operated chuck, Cylinder, cnc turning centers
power operated lathe chucks
Get Price Quote
power operated lathe chucks, Clamping Devices, Soft Jaws
power operated lathe chucks
Get Price Quote
power operated lathe chucks, wood lathe scroll chucks, circular face plates
Power Operated High Speed Chuck
Get Price Quote
Power Operated High Speed Chuck, planetary lapping machine
Power Operated Combined Diaphragm Chuck
Get Price Quote
Power Operated Combined Diaphragm Chuck, lapping plate
