Back Back
Pressure Sensor Cum Switch
100 Piece (MOQ)
Material : Metal
Surface Finishing : Polished
Rating : 0 to 10 Bar
Connect : 1NC, 500mAmp, 12V-24V
Resistance : 0 to 500 n
A device to give proportionate resistance out put with increase/decrease in pressure. This has a built in low pressure switch.
RF Admittance Level Sensor Switches
1 Piece(s) (MOQ)
Level Switches/Sensor : RF Admittance Level Switches/Sensor
Housing : Aluminium, weatherproof IP 67, powder coated , integral with the probe mounting Cable Entry : 1 no.s (standard) Ambinent temperate : 0 to 60 Deg c , Mains Voltage : 18 to30 VDC, Output : PNP NO/NC or Relay ,Operating Freguency : 6 KHz / 110 KHz , COAT GUARD SENSING PROBE: Mounting : Screwed BSP (standard) Or Flanged (optional) or as per specification. Sense rod : Stainless steel Shield : Stainless steel Insulation : PTFE (standard)Other on request and as per application. Operating Temp in :100 deg for the integral switching vessel unit. For higher temp remote switching unit(please consult works) THEORY: The RF level switch operates on the basis of RF absorption measurement. The electronic unit generates a sinusoidal wave, applied to the electrode creating a field around it. RF environment absorption changes (electrical loss) around the electrode are reflected on changes of generator supply current. Such changes, caused by the increase in level is amplified and used to energies the relay. The main drawback of the conventional method is that after the level has once increased and then decreased, there may be a coating left on the probe which is sensed by the instrument as though the level is still on the probe. In JAYCEEADMIT a COAT GUARD and Trance-Conductance amplifier are incorporated in the circuit having its output exactly at the same voltage and phase at all times as its input. The output is connected through the shield of the low capacitance co-axial cable to the concentric tube on the sense probe, called shield element. Since both the elements, sense and shield are exactly at the same potential and phase at all times, there is no current flow through the cable. Thus there is no change in calibration due to coating on the probe and the temperature effect of the cable.
day night sensor switch
250 Per Piece
100 Piece (MOQ)
Power Source : 220-240 V AC
Power Frequency : 50 Hz
IP Rating : IP54
Material : ABS
Uses : Automatic Light on and off
PIR Motion Sensor Switch SM04
750 - 2,100 Per Piece
1 Set(s) (MOQ)
Material : ABS PLASTIC
Voltage : 230VAC
Operating Temperature : 60-80deg C
Frequency : 50HZ
Power : 10-15Amp
Connector : Sensor Switches
Hole Diameter : Holes not required
Setting Range : Not applicable
Brand Name : PIR MOTION SENSOR SM04
Size : COMPACT
Application : ENERGY SAVING DEVICES
Max. Current : 16 AMPS
Max. Voltage : 220-240 VOLTS
Mechanical Life : 2 YRS
Color : WHITE
Warper beam sensor switch
20,000 Per pcs
Application : Industrial Use
Operating Temperature : 20-40deg C
Frequency : 50HZ
Power : 0-5Amp
Beam Pressure sensing switch for Karly Mayer Warper Beam
Smart Switch With Motion Sensor
Based in Pune(India), our organization is involved for years in supplying the finest grade of Smart Switch With Motion Sensor in the industry. We package the entire range of products with industrial-grade wrapping supplies that are environment friendly and safe. Furthermore, the packaging is sturdy to protect against damage and to make sure the product is kept quality assured. Key features : Voltage -200V – 280V AC, 50Hz Output - 2 Kwatt load of Fluorescent Tube Light, CFL, Filament Bulb or any heavy load Reach -10 meters Angle of Coverage -102° Horizontal, 92° Vertical Compact Design & easy installation Load will get off if no motion is detected continuously for 5 minutes Enhances life of Lamps & load by using Zero Crossing Switching Applications- Room & Hotel Lighting, Car Parking & Garden Lighting, Intruder detector with light & Siren etc. Smart Switch with Motion Sensor for Air Conditioner Voltage - 200V - 280V AC, 50Hz Output - 4000W load of 1.5 Ton AC Reach - 10 meters Angle of Coverage - 102° Horizontal, 92° Vertical Compact Design & easy installation Load will get off if no motion is detected continuously for 15 / 30 /45 minutes Enhances life of Lamps & load by using Zero Crossing Switching Applications- Conference room, auditorium.
Diffuse Scan Sensor Optical Proximity Switches
Diameter : M12
Sensing Mode : Diffuse
Sensing Range : 50mm
Housing Material : Brass
Max Load Current : 250mA
Supply Voltage : 10-30 Volt DC
Switching Frequency : 100Hz
Response Time : 1ms
Operating Temperature : -25ºC- +55ºC
Short Circuit Protection : Yes
Connecting Type : 2mtrs,3core pvc cable
Proximity Switches, Proximity Sensor
We are offering proximity switches, proximity sensor, protocontrol now offer entirely new series of proximity switches specially developed for machine tool industry. This series include switches with water-proof right angled connector, oil and coolant resistance cable, scratch proof front cap, weld immune circuit and extended sensing range proximity switches. these switches are used for position, speed, and direction & level sensing. Proxi.switches can replace limit switches with many advantages like: 1) no physical contact 2) no wear and tear, hence long life. 3) no contact bounce. No false pulses 4) non-contact and maintenance free. 5) high repeat accuracy 6) many mounting options are available. 7) led indicator. 8) switches for use in hazardous locations are also available. 3500 varieties of switches are offered. These includes tubular threaded switches from m8 to m 80.sqaure rectangular switches. Slot types switches, in ac and dc versions. inductive proximity switches are generally used for position sensing of metallic parts. speed, direction and rotation of any moving or oscillating machines can be sensed. photoelectric sensors are exclusively used in spm and pharmaceutical machinery. Long range, sensor are used in heavy industries like crane. Sensors with fiber optic cables are available to sense tablet, print mark, pouches and caps.
Day Switch, Night Switch
We are offering day switch, night switch. Switches on lights when it is dark and switches them off when bright. It works on the principle of detecting the ambient light level by means of light sensor and switching potential free contacts. The twilight zone at which this should happen is preset at 10 lux. The seasonal changes in sunset and sunrise are automatically taken care of by the sensor. The unit uses a single light-sensor housed in protectiveness which will also avoid direct light falling on it. The clamp provided for fixing the sensor is easy to fix and flexible to adjust the orientation of the sensor. Salient features : operates directly on 230v, 50 hz supply. Controls load up to 500 watts fully automatic. It is green – it saves electricity. Absolutely maintenance free. No batteries required. No moving parts. Extremely economical – pays for itself in less than 1year. Entire assembly can be directly mounted in open air. Easy mounting clamp. Can be fitted in the housing of any lighting fixture for automatic control advantages : saves electric energy by timely switching. Indirect security measure - unoccupied premise swill have impression of being occupied due to light switching. It offers simplest and cheapest solution in the category.
sensor switch
Features : Very flat building techniques, little design space required, Different switch systems and tactile feeling solutions, Sensor systems integrable, High lifetime and robustness, Dust and water protected
photo sensor proximity switches
Material Presence Sensing Switch
