Roots Cooling System Private Limited Phase 2, Noida, Uttar Pradesh

Our solar shading systems offers, designers the opportunity, for distinctive architectural impact whilst reducing solar heat gains. External solar shading is one of the most effective ways to control the internal conditions of a building. Radiation from the sun is transmitted, absorbed and reflected by the louvres. As a result solar heat gain is prevented from passing into the building, minimizing ventilation requirements and reducing cooling loads. If a controllable system is installed, adjustable louvres track the position of the sun, thereby reducing the numbers of days when the building overheats. Equally, in winter the louvers may be adjusted in such a way that the building benefits from the heat from the sun, and they can be closed at night reducing heat loss. At the same time, daylight levels are enhanced, and levels of glare are reduced.

In many buildings smoke containment systems such as Smokemaster are used to prevent the movement of smoke and heat from one area to another. Smokemaster is rated to contain smoke at a temperature of up to 600 °C for 30, 60, 90 or 120 minutes, depending on which version is selected. SMOKEMASTER IS AVAILABLE IN THREE VERSIONS: Single units (type “SI”). Double vertical (type “DV”) units, where continuous runs with overlapped fabric to form a continuous barrier are required. Double horizontal (type “DH”) units, where there is a premium on space under the ceiling.

As the name implies, Evaporative Cooling works by evaporating water in the air stream. In order for the water to evaporate, the water must absorb heat. Hence, evaporative cooling involves heat & mass transfer which occurs when water and unsaturated air come in contact, and no heat is added to or removed from the system.

Primary purpose of AHU is to distribute conditions air to the occupied zones of a building. The supply air to a particular zone must offset the thermal loads imposed on that zone in order to maintain a comfortable environment for occupants. Because thermal loads for the zones can vary markedly, it is common for an AHU to be controlled to maintain the supply air temperature at a set point value that is sufficiently low to satisfy the zone with the largest cooling load at any given time.

Colt shadovoltaic replaces the glass louvres found in shadoglass with photovoltaic ones. With shadovoltaic we can make the best use of the natural power of the sun's energy. The sun's energy, surely the cleanest form of energy - is directly transformed into electrical power. Shadovoltaic generally incorporates an automatic sun-tracking routine that provides an additional energy yield. The aesthetic effect of the photovoltaic louvres can be individually designed in accordance with the customer's requirements, since cells can be translucent or even transparent.

Louvres of all shapes and sizes may also be covered with teflon-coated woven fibreglass, Colt SHADOTEX. This provides the designer with further exciting possibilities to create impressive façades covered with attractive solar shades. SHADOTEX has a lightweight construction which not only significantly reduces its weight but also permits a fine adjustment of the louvres for the precise control of energy and light transmission. These features make SHADOTEX versatile and flexible. SHADOTEX has been installed for the first time on the HQ Building of the Baader Securities Bank in Munich (architects Baader & Schmid).

Controllable perforated Colt Shadometal louvres were specified by Nicholas Grimshaw and Partners which cover the complete West facade of the A500 Airside Center. The control system adjusts the position of the louvres in response to changing climatic conditions and available daylight. Colt offer two external solar shading systems within the Shadometal range: Solar C is a fixed solar shading system as Brise Soleil that may be installed either horizontally or vertically onto the building façade or roof. Solarfin, is a system of fixed or controllable fins offering greater design flexibility. When linked to a sun tracking controller, Solarfin can offer the most effective degree of solar control without compromising light levels on dull days. Colt offer two external solar shading systems within the Shadometal range: Solar C is a fixed solar shading system as Brise Soleil that may be installed either horizontally or vertically onto the building façade or roof. Solarfin, is a system of fixed or controllable fins offering greater design flexibility. When linked to a sun tracking controller, Solarfin can offer the most effective degree of solar control without compromising light levels on dull days. Louvres are also available in other materials such as glass, wood, terracotta clay and translucent acrylics.

Colt Shadoglass systems are available in four discreet standard designs, and can be designed and configured to meet specific project requirements. Shadoglass combines practical solar control and stunning aesthetics to offer designers a distinctive architectural product that is ideally suited to modern low energy buildings. Glass panels are available in various colours, surface finishes and coatings to meet specific design requirements. Electricity-generating photovoltaic cells may be installed onto the louvres as an option.

Louvre systems are popular with designers for many applications in industrial and commercial buildings. Their purpose can be to control light entry, to provide ventilation whilst maintaining rain defence, to provide screening, or a combination of these. They can also be provided simply for aesthetic impact. Features and Benefits : Aesthetically pleasing Reduced energy costs Enhanced performance Proven performance Easy to install A wide range Upgradeable louvre Design input provided by Colt

Colt Jetstream is an impulse jet fan intended to control air movement and direct polluted air and smoke towards the extract positions in a car park. Car park ventilation systems are required to achieve two objectives. Firstly, when the car park is in general use, it is important that the exhaust fumes produced by vehicles are effectively removed and that there are no stagnant pockets of harmful gases. Secondly, in the event of a fire, assistance needs to be given to the Fire Service to clear smoke from the car park during and after the fire. In addition, car park ventilation systems may be designed to provide clear, smoke free access for fire fighters to tackle the fire, or alternatively to protect means of escape from the car park.

Colt Cyclone is a low profile, high velocity induction fan intended to control air movement and direct polluted air and smoke towards the extract positions in a car park. Car park ventilation systems are required to achieve two objectives. Firstly, when the car park is in general use, it is important that the exhaust fumes produced by vehicles are effectively removed and that there are no stagnant pockets of harmful gases. Secondly, in the event of a fire, assistance needs to be given to the Fire Service to clear smoke from the car park during and after the fire. In addition, car park ventilation systems may be designed to provide clear, smoke free access for fire fighters to tackle the fire, or alternatively to protect means of escape from the car park.

The indirect cooling module (ICM) is a pre-cooler used in 2-Stage or IndirectDirect evaporative cooling. The ICM cools the air without adding any additional moisture. It accomplishes this by circulating water through a sensible heat exchanger, while a fan draws air through the heat exchanger. This air and water are cooled by evaporation and in turn cool the walls of the heat exchanger. The removed heat is exhausted from the unit with the moist air. Hot, dry outside air is pulled horizontally through the cooled walls of the heat exchanger by the attached evaporative cooler. This air is cooled and since it does not come in contact water, there is no moisture added. The dry-air cooled by the ICM is then cooled further by the direct evaporative cooler. The dry bulb temperature of the air after going past the ICM drops as does the wet bulb or saturation temperature. This cooled dry air from the ICM is pulled through wet evaporative media in the direct evaporative cooler which cools the air and adds moisture. In a design summer ambient conditions, the IDEC can lower the incoming air temperature below the existing ambient wet bulb conditions.

Weathered ventilation working on the principle of “Stack Effect” is best suited for most industrial & commercial buildings and can provide both day to day ventilation and smoke extract as well. Additionally, permits the entry of natural daylight too.

The most efficient way of providing natural ventilation to an industrial building would be not to have the roof at al. The hot air generated due to working conditions shape on shop floor would justice and get lost in the atmosphere. Unfortunately this is not practical, so we provide the next best solution with the GRAVENT industrial ventilation system. You will open up your roof to the sky, but we arrange to keep out the sun and GRAVENTS gives free passage to hot air, smoke, fumes etc. (solid arrows) to leave the building irrespective of weather conditions or wind direction. Outside wind (hollow arrows) blowing any direction, always helps extract inside air, Greater Rain, no matter how heavy, drains out on the outside of the roof sheets. Not even a drop comes in, yet there is no obstruction for the exhaust of hot air.

The purpose of a fire curtain is to seal off an area to contain a fire and to prevent that fire from spreading to other areas. A fire curtain is used where, if there is a fire, it is necessary to create a temporary barrier within an opening. This barrier should not be visible at any other time. The Colt FM1 Fire Curtain is low in weight and has minimal dimensions, which enables it to be installed easily in places with space constraints such as within a false ceiling. The Colt FM1 Fire Curtain automatically descends on receipt of a signal from the fire alarm panel or upon loss of power. Once this signal has been reset it automatically retracts.

The Colt FCO (Facade Clear Opening) is a natural louvered ventilator, specially designed to be placed in a facade. The FCO is suitable for natural air supply. Furthermore the FCO can be used for additional daylight. The FCO is applied in (semi-)industrial buildings and utility building.

Double skin construction suitable for outdoor installation. The casing panels shall be made of pre-painted steel sheet externally & plain GSS sheet internally injected with CFC free sandwich PUF material 40 kgm3 density which is non-combustible in nature. The framework shall be made of GSS Aluminum Anodized hollow sheet-steel profiles and PVC corner connections. Suitable airtight access doorspanel with nylon hinges and lock shall be provided for access to various sections for maintenance. Access door shall be double skin construction. The entire housing shall be mounted on heavy-duty channel base frame with anti vibration mounts.

The EuroMeteor is an attractive, low profile, high performance flap natural ventilator which is primarily designed for smoke control applications. Additionally, the EuroMeteor offers the benefit of day-to-day cooling for comfort control applications. The EuroMeteor’s aerodynamic efficiency guarantees a very high performance from a flap natural ventilator and the product is available in a variety of sizes and finishes to suit all industrial and commercial applications. Products manufactured by Colt use 100% recycled material for the principal aluminium components. Features and Benefits : Protection of building structure, occupants and contents in fire emergencies Natural cooling Natural daylighting (even in closed position on translucent flap option) Low running costs Nine sizes to choose from Efficient pneumatic control system Available with aluminium or translucent flaps Virtually maintenance free

Double skin construction suitable for outdoor installation. The casing panels shall be made of pre-painted steel sheet externally & plain GSS sheet internally injected with CFC free sandwich PUF material 40 kgm3 density which is non-combustible in nature. The framework shall be made of GSS Aluminum Anodized hollow sheet-steel profiles and PVC corner connections. Suitable airtight access doorspanel with nylon hinges and lock shall be provided for access to various sections for maintenance. Access door shall be double skin construction. The entire housing shall be mounted on heavy-duty channel base frame with anti vibration mounts.

It is a method of providing ventilation in a Car Park by adding momentum to the air, by installing small unitary fans under the ceiling to generate thrust. These units remove the need for large runs of ductwork as they push smokefumes to a central extract arena.