Back Back
Tarplastic Waterproofing sealant
TarPlastic® is a cold applied bituminous caulking compound with mineral fillers in a volatile solvent to retain its plasticity. It is available in a putty form. TarPlastic® remains plastic for a considerable length of time. The skin and interior harden to some extent after application. It conforms to the requirement of IS : 1580 – 1991. Application It is ideal for use in situation where certain degree of expansion, contraction and vibration is expected, like around J Hooks used for fixing Asbestos / GI sheets. It can also be used for caulking various types of roofs and masonry walls, including Fully plugging gaps in tiles caused by sagging of battens or otherwise in case of tiled roofs. Filling minor cracks / gaps in terraced roofs or other locations. Advantages Cold applied and ready to use. Does not require specialised handling for application. Does not creep or flow when applied on vertical or sloping surfaces. Remains plastic for a considerable time and, therefore, can accommodate a good degree of expansion, contraction and vibration. Packing Available in 200 Kg, 20 Kg, 4 Kg and 1 Kg Containers. Storage Keep in cool and dry place in air tight container under shed away from heat. Health & Safety Lid of the container should be firmly fixed, when not in use. Inflammable and hence keep away from direct flame. TarPlastic® shall have no harmful reaction, when it comes in contact with drinking water. Use goggles, hand gloves and trowel during application. Clean hands with warm soap water after application Application Methodology Surface must be clean, dry and free of grease, oil and painting compound. Concrete surface must be dry and stable (atleast) four weeks. Check that mastic is compatible with surface in terms of adhesiveness, staining and chemical compatibility (test a section first). If necessary apply a thin layer of Sealant Primer on the surface. After the primer has dried press flexible non adhesive filler on to the groove. The joint filler should be free of holes to ensure that bubbles do not form in the joint. For better finish use protection strip. For a narrow joint apply the mastic in one movement and for very wide joint, apply the mastic in three places: The first two on the edges of the joint and third in the joint filler. Smooth out with soapy water. Press the mastic against the edges and the joint while taking care not to create air bubbles. Remove protection strip.
...more
TarFelt LM
TarFelt LM is a single component, water based elastomeric polymerized bituminous emulsion with selected graded fine fillers and some additives TarFelt LM is applied by brush / roller without any use of heat. TarFelt LM forms a tough, elastomeric, monolithic, seamless water proofing membrane. For non-trafficable roofs, TarFelt LM may be coated with SuperSilverShield (aluminium finish) or with ShaliCryl 215 providing desired colours for aesthetic look or simply by sprinkling sand. For Trafficable roofs / areas, TarFelt LM shall be protected with screed / tiles / china mosaic. TarFelt LM +, in addition to properties of TarFelt LM, provides insulation. Applications Renovation of old aged hessian based membrane by applying TarFelt LM over the cleaned surface without removing such old aged membrane. Waterproofing of corrugated metal / asbestos sheets and other difficult geometrical shapes. Water proofing of roof, balconies, planters, swimming pools, roof gardens, terraces, parking area, and water reservoir. Facade damp proofing Advantages Water based product, cleaner technology, non toxic. Easy to apply by brush / roller. Cold applied and hence does not require heating. Excellent impermeable. High crack bridging property. Good flexibility and does not crack on aging. Allow it to dry till it becomes tacky. Apply the first coat of TarFelt LM by brush / roller / spray on primed surface. Coverage shall depend on application and surface finish. Please refer Product . Literature. For trafficable area, protect TarFelt LM with screed / tiles / china mosaic. Allow the first coat to dry with the fiber / mat spread as above. Apply second coat of TarFelt LM and saturate the reinforcement totally. Health & Safety Use mask, nose cover and hand gloves during application. Clean hands with soap water after application. Packing Available in 20 kg pack. Storage Store in a cool dry place, under shed, away from heat. Shelf Life 1 year in original unopened sealed condition.
...more
TankMastic bituminous coating
1,800 Per Container
TankMastic® is a specially formulated anti-corrosive, tasteless, odourless, non-toxic and black bituminous coating for protecting the internal surface of storage water tanks, pipes, etc. from corrosion. It conforms to IS: 9862/1981 as well IS: 158/1981. Application TankMastic® provides corrosion protection coating to all types of iron, steel including drums, and masonry or concrete surfaces for fixing glass panels on building elevation. • It, being non-toxic / odourless, is suitable for coating insides of masonry / steel water tanks. Advantages It is easily applicable by brush/spray gun. It dries rapidly leaving black glossy finish. The resultant film is tough and elastic and does not crack easily due to structural movements. It is resistant to diluted acids and alkalis. It is non-toxic and does not impart odour or taste to water or other contents in contact. Health & Safety Lid of the container should be firmly fixed, when not in use. TankMastic® shall have no harmful reaction, when it comes in contact with drinking water. Use goggles and hand gloves during application. Clean hands with warm soap water after application Packing Available in 1 Ltr, 4 Ltr, 20 Ltr and 200 Ltr drums. Storage Keep in cool and dry place in air tight container under shed away from heat. Application Methodology The base metal should be cleaned thoroughly by sand blasting or otherwise. Before application, surface should be totally dry, free from moisture, oil, grease, mill scale or rust. For better performance, a coat of ShaliTex® Primer is recommended on metallic surfaces, However, for concrete or other porous surfaces, a coat of ShaliTex® Primer is pre-requisite. ShaliTex® Primer should be allowed to dry hard before TankMastic® is applied TankMastic® must be stirred properly before applying by brush or spray gun. Two coats of TankMastic® are recommended for concrete and three coats for metallic surfaces.
Type : Liquid
Brand Name : STP Limited
Color : Black
State : Liquid
Application : Metal
...more
Super Thermolay waterproofing Membrane
Super Thermolay is a uniquely formulated prefabricated waterproofing Membrane with a special multilayered design, with superiorpliability, tensile strength, workability and resistance to the elements. This combination gives the proven waterproofing qualities of bitumen plasticity, excellent resistance to heat, aging and weathering, and ease of application by torch welding. The multilayered design consists of a 160 gsm polyester core coated on both sides with APP (atactic polypropylene) modified bitumen and finally finished with thermofusible polyethylene film. The polyester core gives the membrane high tensile strength, elongation and superior lap joint strength.
...more
super silver shield
SuperSilverShield® is an anti-corrosive, water proofing paint with aluminum finish, It is composed of oxidized bitumen, volatile solvents and specially formulated aluminum compound. Application SuperSilverShield® is used as a protective coating on iron, steel, masonry and other surfaces. It is used to reflect UV rays and protect bituminous waterproofing felts and fabrics, while giving a visually pleasing finish. It covers, in normal conditions. 9 to 11 Sq.M / Ltr when applied over metal and old painted surfaces. 7 to 9 Sq.M / Ltr when applied over bituminous surfaces. 5 to 7 Sq.M / Ltr when applied over brick masonry and concrete. Advantages Deflects UV rays and prevents degradation of membrane arising out of exposure to sunlight. Reduces heat radiation inside the buildings and thus provides a little insulation from atmospheric temperature. Packing Available in 20 Ltrs drums. Health & Safety It is inflammable, keep away from any naked flame during application and storage. Use goggles and hand gloves during application. Clean hands with warm soap water after application. Storage Store in air tight containers in cool, dry place, under shed away from heat and moisture. Application Methodology SuperSilverShield® is to be stirred well before use to ensure thorough dispersion of aluminium for a uniform finish. Loose dust should be brushed off and surface should be dry before application. Undercoat is not necessary for its application. It can be applied over old painted surfaces without burning off or scraping, provided the old surface is not in a flaky condition.
...more
shalitex primer
95 Per Litre
ShaliTex Primer is a solvent based bituminous primer that seals pores in surfaces such as concrete and improves the adhesion of bituminous materials that are to be applied to the substrate. It is suitable for brush or spray application. It conforms to the requirement of IS: 3384-1986. Application Priming bituminous, concrete or masonry surfaces prior to laying membrane promotes bonding, whether self-adhesive or otherwise. Applied in canal lining joints and concrete floor joints prior to pouring of the bitumen sealing compound for bonding. Advantages Seal pores on surfaces such as concrete. Improves the adhesion of bituminous material that is to be applied to the substrate. Health & Safety Lid of container should be firmly fixed, when not in use ShaliTex Primer is inflammable and hence keep away from heat. Use goggles and hand glove during application. Clean hands with warm soap water after application. Packing ShaliTex Primer is available in 20 Ltr & 200 Ltr drums. Storage Keep in cool and dry place in air tight containers under shed away from heat. Application Methodology Ensure not to apply when temperature is less than 5 0 C or during foggy period. Before applying the primer make the concrete surfaces free from dust and sand particles by brooming and allow it to dry. Concrete should be cured and should be eight days old. ShaliTex Primer should be thoroughly stirred before use and applied to the substrate by means of brush, roller or spray at the rate of 0.30 Ltr / SqM. Allow it to dry for 24 hours.
Type : bonding primer
Brand Name : Stp limted
Color : black
Application : metal
Color : black
Type : Bonding Primer
Brand Name : STP Limited
...more
Shalitex Board
Shalitex Expansion Joint Board is cane fiber soft board impregnated with Special Grade of Bitumen. It is a perfect base material for expansion joint filers. The board's compression and recovery characteristics conform to the U.K., U.S.A. and Indian Standards much above the required averages. Shalitex Expansion Joint Board displays excellent resistance to compression, with outstanding recovery characteristics. The boards are environment friendly as opposed to the environment destroying thermos Cole/plastic expansion joint boards. Application Filling structural expansion & structural separation joints in block & in situ concrete construction including screed floors, motorways, roads, runways, pedestrian areas, bridges, curbs, basements, retaining walls, site slabs, subways & other structures etc. Filling all types of expansion joints in piers and lateral supports like abutments. Various other flat works and concrete floors. Storage Keep in cool dry place under shed away from heat. Health & Safety Use goggles and hand gloves during application. Clean hands with warm soap water after application. Packing Available in 12, 18 & 25 mm board normally in 4 Ft x 4 Ft. Other thickness may be catered to on request. It is available in a wide range of sizes, both as boards & strips in thicknesses of 12, 18 mm & 25 mm. Application Methodology Permit free movement of the concrete slabs during expansion and contraction. To provide a waterproof seal. To resist entry of foreign matter into the joint space. Application methodology. Remove dust, flakes or foreign particles by jet or dry air and clean the surface. Apply appropriate primer like ShaliTex Primer, ShaliJet Primer, ShaliSeal PS Primer in the groove where SEJ Board is to be applied. Cut SEJ Board of appropriate width from the desired thickness and place the same in the groove in a way to flush with the external surface except for space required for ShaliBar / other sealants. In case of a new casting, SEJ Board of appropriate width is fixed with copper screws before pouring concrete. The width is designed to flush with the external surface except for space required for ShaliBar / other sealants. In highway construction, SEJ Board is placed appropriately 20 mm below surface of finish level of pavement and filled with ShaliTex Sealing Compound / ShaliJet Sealing Compound / ShaliSeal PS.
...more
shalimastic paint
Cold applied liquid product Protection for buried / submerged surface or equipment. Coating interior / exterior surfaces of metal or concrete tanks, culverts, steel pilings, filter screens, sluice gates, tank bases, trestles etc. Coating of interior / exterior of barges and under-water structures. Advantages Unaffected by marine organisms, soil chemicals and soil bacteria. Highly resistant to corrosive attacks of sea water and alkalis. Retains its pliability over a wide range of temperatures. Provides an abrasion resistant tough coat which is 5-8 times thicker than a coat of ordinary conventional anti-corrosive coatings. Provides a void-less, joint-less continuous film capable of taking expansions and contractions without cracking. Acts as an excellent water repellent coating even under severe corrosive conditions. Health & Safety ShaliMastic® HD / LC is inflammable. Use goggles and hand gloves during application. Clean hands with Isopropyl alcohol followed by warm soap water after application. Packing Available in 26 Kgs and 260 Kgs containers. Storage Keep in cool and dry place under shed away from heat. Keep lid of container closed tightly when not in use. Application Methodology The base metal is thoroughly cleaned either by sand blasting, wire brushing or by any other means. Before application, ensure that surface is totally dry and free from moisture, oil, grease, mill scale, rust or any other foreign particles. A coat of Jet Set® Primer Type A is recommended before application for better performance. The primer must be hard dry before application of ShaliMastic® HD / LC. ShaliMastic® HD / LC, being a thixotropic material, has to be stirred properly first. It is then applied using a brush. Two coats are recommended for concrete and three coats for metallic surfaces. ShaliMastic®-HD should not be applied over shop-coating (particularly red oxide coating).
...more
Shalikote T-10
850 Per Drum
ShaliKote® T-10 / ShaliKote® T-10A is recommended for waterproofing of leaky walls / surfaces or places where heating of bitumen is not desirable or prohibited. Advantages ShaliKote® T-10 gives a coating, which, when set, is impermeable to water and remains unaffected by attacks of industrial fumes, saline atmosphere, etc. It resists low temperature cracking and also does not crack under the influence of strong sunlight. ShaliKote® T-10A has smoother finish and better flow as compared to ShaliKote® T-10 Health & Safety Lid of the container should be firmly fixed, when not in use. Use goggles and hand gloves during application Clean hands with water after application. Packing ShaliKote® T-10 / ShaliKote® T-10A is available in 20 kg and 200 kg drums. Storage Keep in cool and dry place in air tight containers under shed away from heat. Application Methodology Wire brush and clean the surface thoroughly to remove all dirt and loose particles. Dilute ShaliKote® T-10 from its pasty consistency to light consistency by adding water in the ratio of 1:1. Apply this diluted material on the roof surface as primer. No dilution should be done in case of ShaliKote® T-10A. When the primed surface is dry and has turned black from its original brown colour, apply ShaliKote® T-10 and allow the emulsion to break. It will turn black from its original brownish colour. When the emulsion has set in, spread coarse sand or crushed stone chips over the surface.
Size : 20 Kg
Type : Coatings
Material : bitumen based
Certification : ISO 9001:2008 Certified
Application : Flooring, Wall Coating
Form : Liquid
Feature : Water Resistant, Waterproof
Speciality : Pasting On Walls
...more
Shalibond BS
Recommended for sticking roofing felts on metal, timber, tiles, asbestos, concrete and masonry surfaces, including roofs of trains, buses, tramcars, railway carriages, etc. Advantages ShaliBond BS/CS is cold applied adhesive and does not require any torching. Therefore, it is useful for applications where use of hot bitumen / torching is difficult or prohibited. Health & Safety Lid of the container should be firmly fixed, when not in use. ShaliBond® BS/CS is inflammable and hence keep away from flame. Use goggles and hand gloves during application. Clean hands with warm soap water after application. Packing Available in 1 Kg, 4 kg, 18 Kg and 180 Kg drums. Storage Keep in cool and dry place in air tight container under shed away from heat. Application Methodology Surfaces should be cleaned of all foreign materials and should be completely dry. Apply ShaliBond BS/CS over the cleaned surfaces with a spatula or brush. Allow approximately 10 minutes time before laying the felt and sticking the same by application of uniform mild pressure. For more effective waterproofing, seal overlaps and termination by affixing 6 inch flashings of the membrane on overlapping area after application of ShaliPrime APP.
...more
self adhesive membrane
250 Per Square Meter
Brand Name : Asian Paints
Type : membrane
Color : black and white
Country of Origin : Made in India
...more
PypKote Wrapping tape
255 Per Square Meter
Pypkote is pipeline corrosion resistant tape conforming to IS:10221 appendix B specification. It comprises of a tar-based polymeric mix supported on a fabric of high tensile strength fibreglass. The polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. The tape is terminated on both exteriors by thermofusible HMHDPE Film which aids in the installation process.
Type : Pipe Wrapping Tape
Material : Pipe Wrapping Tape
Application : Wrapping Pipe
Certification : ISO 9001:2008 Certified
Color : Black
Design : Plain
Packaging Type : Other
Adhesive Side : Single Sided
Adhesive : Hot Melt Adhesives
Feature : Heat Resistant,Waterproof
...more
PypKote Bitumen based Pipe Coating Tapes
150 Per Square Meter
Pypkote is pipeline corrosion resistant tape conforming to IS:10221 appendix B specification. It comprises of a tar-based polymeric mix supported on a fabric of high tensile strength fibreglass. The polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. The tape is terminated on both exteriors by thermofusible HMHDPE Film which aids in the installation process.
Type : Pipe Wrapping Tape
Material : Pipe Wrapping Tape
Application : Wrapping Pipe
Certification : ISO 9001:2008 Certified
Color : Black
Design : Plain
Packaging Type : Other
Adhesive Side : Single Sided
Feature : Heat Resistant,Waterproof
Adhesive : Hot Melt Adhesives
...more
Polysulphied Sealant
210 Per Kilogram
Polysulphide based elastomeric sealant for joints subject to movement CICO SEALANT T 680 is two pack Polysulphide based joint sealant available in GUN GRADE and POUR GRADE. CICO SEALANT T 680 gun grade is a gun-applied, non-sag type for vertical joints and CICO SEALANT T 680 pour grade is for horizontal movement joints. When two packs are mixed, i.e. Polysulphide resin (Pack-A) with curing agent (Pack-B), it forms a tough, flexible, durable rubber like material with strong adhesive properties on most building substrates and joints. Characterstics It is used to form long lasting weather –resistant and waterproof seals in expansion joints. Has long lasting elasticity Has high movement capacity Chemical resistant Gun grade for vertical joints Easy to pour on horizontal joints with pour grade
Packaging Type : Plastic Tube
Application : Construction
Form : Liquid
Brand Name : Dr
Packaging Size : 0-5kg
Feature : water Resistant
Type : Polysulphide Sealants
Grade : Chemical Grade,Industrial Grade
...more
Polysulphide Sealants
210 Per Kilogram
techseal rdl 940/941 are two-component sealant based on thiokol - polysulphide liquid elastomer. it consists of a base compound and accelerator (curing agent). when the two components are mixed before application, a chemical reaction is initiated which cures instantly to a firm, flexible rubber-like seal with excellent adhesion to concrete, masonry, wood, glass, acrylic and pvc plastics. it is capable of withstanding repeated extension, compression & cyclic movements without the loss of adhesion and resists deterioration by weathering, sunlight, ozone, water, salt, oils and fuels. it is far superior to all the conventional joint sealing material like bitumen, mastics, metallic channels and expansion sheets. rdl-940 (gun grade) is a non-sag material used for sealing of horizontal, vertical & ceiling joints. rdl-941 (pour grade) is a pourable & self levelling material used for sealing of horizontal joints only. .
Type : Polyurethane Sealants
Application : Construction
Grade : Industrial Grade
Form : Liquid
Packaging Type : Drum
Feature : Heat Resistant
Packaging Size : 1kg,4kg
Surface of Application : Ceramic, Wood
Brand Name : choksey
Application : Creamic/wood
...more
polyfelt
Shali Plus 20 is a polymeric waterproofing membrane. It has a center core of 20 micron High Molecular High Density Polyethylene (HMHDPE) film coated on both sides with Polymer Modified Bitumen, which is protected by a thermo fusible film. The HMHDPE Film is the reinforcement barrier against water and moisture. The polymeric membrane has an elongation exceeding 300% to absorb all structural movements and has a very high tensile strength and cold flexibility to adapt to all contours. Shali Plus 20 is also available with 40 micron aluminum topping on the top side to prevent disintegration of bitumen and provide UV protection
...more
Non Woven Geotextile
IWL Medium Setting Emulsion (MS)
5,800 Per Barrel
bitumen emulsion is a mixture of fine droplets of bitumen and water. But as the bitumen is a petroleum product it doesn't mix with water and as it is sticky, it doesn't easily get disintegrated into fine droplets. To overcome this problem an emulsifier is usedrapid setting emulsion (rs)* medium setting emulsion (ms)*slow setting emulsion (ss)
Type : Emulsion
Brand Name : IWL
Material : Tar
Application : Road Construction, Roofing Felt, Waterproofing
Color : black
...more
Joint Filler Board
550 Per Piece
It is a pre-moulded, high-performance joint filler board. It is a closed-cell and of cross-linked structure. It has an excellent recovery of 95% (after compression up to 50%), which makes it the most suitable product for this application. It is an exclusive product specially designed to be used as expansion joint filler in concrete, brick, blockwork and isolation joints. It is rot free and contains no bitumen. Advantages: The closed-cell structure resulting in negligible water/moisture absorption Excellent recovery after compression High resistance to chemical like most Bitumen free hence non-staining and free from bleeding Easy to cut, hand and install Rot proof hence does not age and disintegrate over prolonged use Use of ShaliBar/Backer rod is optional
Type : Bitumen Fibrer Fille Board
Certification : ISI Certified
Color : Black
Condition : New
Size : 4ft x4ft
Brand Name : Stp Limited (Shalimar tar product ltd)
Thickness : 12,20 and 25mm
Density : 250 kg/m3
...more
Insulation Board
605 Per Square Meter
XPS BOARD is an Extruded Polystyrene (XPS) rigid board used for thermal insulation. It is produced from general purpose polystyrene by the process of extrusion. These extruded sheets have a closed-cell structure and virtually no air-voids in between the cells. Globally XPS has been widely used for thermal insulation since the last 40 years. It is acknowledged to be one of the best 'value-for-money' thermal insulation materials. In India XPS is manufactured by Supreme Petrochem Ltd (SPL) as INSUboard at India's first integrated ultra-modern manufacturing facility at Nagothane, Maharashtra. This eco-friendly plant has an annual production capacity of 150,000 m3 and is part of the 333 acre styrenics complex of Supreme Petrochem Ltd.
Size : 600mmx1200mm
Type : Extruded Polystyrene Board
Thickness : 25mmx100mm
Color : Light Green
Feature : Waterproof
Width : 1200mm, 600mm
...more
Expansion Joint Filler Sheet
300 Per Piece
construction of concrete roads, runways, floor and roof slabs of buildings, involves the casting of concrete in slab form, which leads to construction joints. provision must be made to accommodate the expansion and contraction at these joints which occur with seasonal variations in temperature. our bitumen impregnated expansion joint fillers boards display excellent resistance to compression, with outstanding recovery characteristics. provision of these boards in the joints permits free movement of the concrete slabs. this prevents damage to the slabs besides providing waterproofing and resisting the entry of foreign matter into the joints
Type : Bitumen Fibrer Fille Board
Certification : ISI Certified
Color : Black
Condition : New
Size : 4ft X4ft
Brand Name : Shalitex Board
Material : Bitumen Pad
Density : 250
Color : Black
...more
Dura Silfil Armour Board Supreme
200 Per Square Meter
This board is a closed-cell polyethene joint filler. It is suitable for use as a joint filler in buildings and other concrete structures where a readily compressible joint filler is required. Features: Lightweight & durable Waterproof Resilient Non impregnated Non-staining & non-bleeding Chemically inert Rotproof
...more
Dura Board
30 Per Square Meter
Formerly: SIL flex / CAPCELL HD100 The most compressible filler board for expansion joints DURAboard HD100' is a high performance crosslinked, The most compressible filler board for expansion joints is a high performance crosslinked, Pre-moulded, compressible joint filler board. It is readily compressible filler board that ensures low load transfer. ‘Polymer Expansion Joint filler’ (expansion joint filler board) is a non-bituminous superior alternative to bitumen boards.
Size : 1200mmx2400mm
Type : Insulation Material
Material : Rubber
Color : Black
Pattern : Plain
...more
Dura Armour Board
This board is a resilient closed cell polyethylene joint filler. It is suitable for use as joint filler in buildings and other concrete structures where a readily compressible joint filler is required. Advantage Expansion joint filler material for buildings... Supreme Pe Foam Sheets Closed Cell Polyethylene Joint Filler Compliance BS 5628 Part 3 Featrures Light weight & durable Waterproof Resilient Non impregnated, Non staining & non bleeding Chemically inert Rot proof Available in various thickness from 10mm to 100mm
...more
Waterproofing Services
Reviews & Ratings
Write a ReviewBe first to Rate
Rate ThisOpening Hours
Share your Correspondence Details to receive messages from Shiv Sons
