Unitrade Pashan, Pune, Maharashtra

This next-generation Refrigerant Leak Detector D TEK Select uses an innovative infrared absorption sensing cell that is extremely sensitive to all refrigerants. D-TE K Select maintains that sensitivity over time for consistent, accurate and reliable performance. The sensing cell lasts for approximately 800 hours. The Latest D TEK Select is also improvised with a charging status indicator, sensor failure indication, and NiMH (nickel metal hydride) batteries. All in an easy-to-use unit with the quality and durability How it Works At the heart of the D-TE K Select Refrigerant Leak Detector is an infrared absorption filtometer. It consists of a sampling cell with an infrared source (or emitter) at one end, an infrared energy detector at the other end, and an optical filter in between them. Like the visible light we see, infrared energy is part of the electromagnetic energy spectrum. Most materials absorb specific and known wavelengths of infrared energy. The particular wavelengths of energy absorbed by a material are known as its absorption spectra. All refrigerants have similar absorption spectra in the range of 7.5–14 micrometers. The infrared source (emitter) creates a high-intensity stream of energy incorporating all wavelengths in the infrared spectrum. The stream passes through the optical filter, which blocks all wavelengths except those that refrigerants absorb. The filtered infrared energy strikes the detector and causes it to heat up. When refrigerant is drawn through the sampling cell by the internal pump, some of the infrared energy is absorbed by the refrigerant. This causes a decrease in the amount of infrared energy reaching the detector and a corresponding drop in the detector’s temperature, which triggers the D-TE K Select to alarm. This whole process takes a fraction of a second. FEATURES AT A GLANCE 0.10 ozyear (3 ga)sensitivity Sensitive to all refrigerants, including R-22, R-134a, R-404a, R-410a, R-507 (AZ-50) and all CFCs, HCFCs and HFCs.800-hour infrared cell life for low cost of ownership.Infrared cell does not weaken over time, so response remains consistent and accurate.Infrared cell cannot be overloaded or “poisoned” by exposure to large amounts of refrigerants.High-efficiency air sampling pump provides quick response and quick clearing (“zeroing”).On-board diagnostics indicate charging status and warn of low battery or infrared cell failure.N iMH power stick is environmentally friendly, won’t corrode, and provides greater charging capacity.Enhanced filter design for superior filtration and resistance to contaminants.Ability to run off AC power adapter.

Whisper Ultrasonic Compressed Air Leak Detector has unmatched quality and inexplicable performance in detecting the frequencies in the 40.5 KHz range The Ultrasonic Leak Detector is very effective in detecting leaks in pneumatic control systems, compressed air systems, vacuum systems etc. Additionally, electrical arcing and worn bearings is also detected using the Compressed Air Leak Detector. With a sophisticated electronic circuitry, Whisper locates the source of this ultrasonic sound, making it a versatile tool which can be used in various applications. An Internal Noise Control ensures Whisper is unaffected by audible noise, making it possible to use in noisy environment. Features Leaks in pneumatic control systemsLeaks in compressed air systemsLeaks in vacuum systemsLine set leaks in foundations wallsDiagnosing solenoid operationsMade in U.S.A

GAS Mate Combustible Gas Detection is Portable and Hand held Device that makes the detection of various gases a simple task. GAS Mate effectively detects gases like Natural Gas, Propane, Butane, Cyclopentane, Ethane, Ethanol, Isobutane and Ammonia. The sensitivity power is up to 5 PPM Methane i.e. twice as sensitive as nearest competitor. The detectors also have a flashlight and audio alarm to indicate the leakage of gas. We also provide 1 year replaceable warranty for our Combustible Gas Leak Detector. Features Sensitive to 5 PPM Methane (twice as sensitive as nearest competitor).Also detects Natural Gas, Propane, Butane, Cyclopentane, Ethane, Ethanol, Isobutane and Ammonia.Variable audio alarm and flashing LED indicate leak strength.Adjustable sensitivity helps pinpoint leaks fast.Auto zeroing for ignoring background gas levels in leak test area.Small sensor and probe tip permit leak Checking in tighter places.Runs continuously for 60 hours on two alkaline D-size batteries.1 year replacement warranty.

Our Automatic Drain Valves are designed to remove Condensate from Compressed Air Systems. Typical installations are on Compressors (after coolers), Dryers, Receivers (Air Tanks), Driplegs and other Compressed Air System Components. Programmable Motorised Drain Valve, Model TEC-44 The TEC-44 is designed to remove high viscosity effluents / condensate at pressures upto 40Bar .The Microprocessor Controlled Motorised Ball Valve is powered by a powerful motor and an efficient gear train, and features a 10 channel programmable cycle with LCD, valve open indicator, test button, anti block system and a battery backup to protect against power failure. The TEC-44 can be programmable to open between 3 sec to almost 15 minutes and the cycle can be adjusted between 4 min and 24 hours, allowing unbelievable flexibility of operation and the 12 mm orifice, can handle huge Condensate discharge in a controlled manner. Auto Drain Valve TEC-11 : FOR COMPRESSED AIR FILTERS designed to drain condensate from all compressed air FILTERS regardless of filter capacity. The in-line design allows for fast efficient installation. The TEC-11 can be matched to any model / brand or type of filter. Auto Drain Valve JORC : EZ-1 ECONOMY DRAIN The EZ-1 is produced with a 1/4� valve connection and in 230 VAC or 115 VAC versions. The limited variations have allowed for massive production batches and subsequently a reduction in cost. The reliability factors have remained in place such as Viton seals, large orifice etc. Auto Drain Valve JORC : COMBO The COMBO is an all-in-one timer drain with an integrated ball valve and strainer The unit offers true bme savings during installation procedures. The valve is protected due to the integrated ball valve and strainer The unit can be shut off from the compressed air system enabling easy and safe maintenance work to be carried out. Auto Drain Valve JORC : OPTIMUM (High Pressure upto 400 Bar) : The Optimum has a wide range of veriations and options such as valve connection sizes in both BSP or NPT and pressure/voltage options. The �new futuristic look� allows the OPTIMUM to make its mark well into the new millennium. The OPTIMUM replaces the very familier TEC-22 range. More options are in NICHE products. Auto Drain Valve JORC : SMART GUARD Pro : Zero air loss drain Valve: The SMART GUARD Pro drain system uses state-of �the art software in combination with a special transducer interface to measure the presence of condensate, volumetrically, 50 times per second. There is no loss of compressed air; Continuous monitoring insures fast, effective discharge of condensate up to 1000 liters condensate per hour. There are no Sensors to foul up and the unit functions equally well with clear water or heavily emulsified and dirty condensate. The SMART GUARD Pro operates in a pressure range from zero to 16 bar and the large condensate removal capacity makes it suitable for all applications, regardless of size. An alarm feature is incorporated as standard. Auto Drain Valve JORC : NUFORS :The Nufors removes condensate from compressed air systems. The operation is automatic and there is no unnecessary compressed air lost during the condensate discharge cycle. The NUFORS uses pneumatic forces to operate the valve assembly and is ideally suited in applications where power is not available, too expensive or not reliable. The large orifice, combined with the large discharge capacity make this drain suitable for all compressor capacities.