Abrasion Tester Dealers in Ahmedabad (16 products available)

Brand Name : KJ

Voltage : 415 V

Features : Efficient performance, Corrosion resistant, Tough construction

Material : Mild Steel

Phase : 3

Frequency : 50 Hz

Material : MS

Phase : Single

Frequency : 50 hz

Length : Up to 8 inch

Type : Abrasion Testing Machine

Weight : 100-500kg

Color : Black, Brown, Grey, Maroon, Red

Voltage : 220V

Condition : New

Application : Testing

Automatic Grade : Automatic

Power : 1-3kw, 3-5kw, 5-10kw

Warranty : 1 Year, 2 Years

Certifications : ISO 9001:2008

Eccentricity of axis of rotation of the disc : 22.5 mm

Speed of rotation of disc : 300 ± 10 rpm

Max no of test specimens tested at a time : 4 no

Inside dia of specimen holding ring : 83 mm

Inside height of specimen holding ring : 25.5mm

Dist of center of test area from cent of disc : 195 mm

Electric Motor : 1/4 HP, Single-phase, 230 Volts, AC

Electronic Counter : 4 digits pre-set type electronic counter with memory back up and key-lock reset.

Features : Easy to use and with rugged construction,Electronically controlled RPM Indications,Mild steel structure body with powder coating paint

The machine is used for testing crushed slag, crushed and uncrushed gravel for resistance to abrasion. The aim of the test is to find the percentage wear due to the relative rubbing action between the aggregates and steel balls used as abrasive charge. The oven dried aggregates are weighed and rotated along with abrasive charge in the machine for the 500 or 1000 revolutions and percentage of wear so found out is reported as Los Angeles abrasion value. The machine consists of a hollow cylinder mounted horizontally on a sturdy frame on ball bearings. There is an opening which can be closed with adjust tight cover to facilitate charging and discharging the drum with the material under test. A detachable shelf which extends throughout the inside length of the drum which catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated by an electric motor through a heavy reduction gear at a speed of 30-33 R.P.M. A revolution counter is fitted to the frame. A tray is supplied for collection of the material at the end of the test. Complete with abrasive charge consisting of a set of twelve hardened steel balls, approximately 48mm dia, suitable for operation on 440V, 3 phase, 50 cycles, A.C. Supply.

Material : Mild Steel

Brand Name : Asia Vision Instrument

Frequency : 50-60 Hz

Rotating Speed : 60 RPM

Capacity : 200 kg.

Tile Flexural Testing Machine Capacity 200 kg. for cement concrete flooring tiles. The specifications are similar to the above machine, but for the bearing rollers of 25 mm dia and spans of 150, 200 and 250 mm. The load is applied at the rate of 200 kgminmeter. Without lead shots.

Power : Hydraulic

Brand Name : EIE

Port : Nava Sheva, Maharasta

Model Number : Los Angeles Abrasion Testing Machine

Packaging Details : Packaging of the instruments will be done in the wooden case. Extra charges for freight, forwarding and packaging

Place of Origin : Gujarat, India

Platform Diamete 140mm Platform Rotation Speed 60 + 2 RPM Dimension of Rubber Disc 50mm dia x 12.7mm width Hardness of Rubber Disc 50 to 55 IRHD (Shore-A) Dist : Platform Diamete

140mm : Platform Rotation Speed

60 + 2 RPM : Dimension of Rubber Disc

50mm dia x 12.7mm width : Hardness of Rubber Disc

50 to 55 IRHD (Shore-A) : Distance between Face of Disc

50 to 55mm : Load of Rubber Dis

5.4 + 0.2 N (550 + 20gm) : Suction by Vacuum

1.5 to 1.6 kPa min : Suction Nozzle Distanc

77mm :  

OTHER FEATURES: : Rotation By Digital Programmable Counter. Total Rotation Counting On Digital Display. Vacuum pump Compact Vacuum pump with vacuum system.

Rotation : By Digital Programmable Counter.

Total Rotation Counting : On Digital Display.

Vacuum pump : Compact Vacuum pump with vacuum system.

Standards ISI2673-1989, IS-2634-1987,IS-3919-1987,IS-635801971 and ASTM D- 4966 This precision built multi-purpose machine Rubs the material in Multi-direction for measuring resistance to surface. The path traces by Multi-motion is known as Lissaious Figure, changes from a circle to gradually diminishing ellipses until it becomes a straight line. The multi direction motion can easily be converted into a uni-direction motion. The instrument is equipped with solid stat electronic digital pre-settable counter of 5 digit. The Standard weight of each specimen holder is 400 gms.

  Introduction For the determination of resistance of aggregate to wear by abrasion. Two hollow cylinders, closed at one end and provided with tightly fitting covers at the other end. The inside diameter of the cylinder 20 cms and 34 cms depth. The cylinders are mounted on a shaft at an angle of 30° with the axis of rotation. The shaft rotates at 30-33 rpm through a reduction gear, coupled to a motor. Suitable for operation on 440 volts, three phase, 50 cycles, AC supply. Supplied complete with a counter and push button starter. With 12 nos cast iron spheres or steel spheres (steel balls) hardened, approx. 48 mm in diameter, each weighing 380-445 gm.

The tile sample is pressed under a specified load against a grinding path, strewen evenly with an abrasive powder, revolving at the rate of 30 ± 1 rpm. At the end of 100 revolutions of the disc, the second parallel side of the tile is subjected to wear an equal number of revolutions of the disc.The wear of the tile is measured using AIM48101 thickness measuring device (which is supplied at extra cost). The Abrasion Testing Machine consists of a replaceable grinding path, fitted on to a disc rotating about its vertical axis. The rotating disc and the grinding path are enclosed by a circular tray. A bracket holds the specimen. The loading is by a counterbalanced lever. A funnel is provided to facilitate charging the grinding path with abrasive powder.Supplied complete with automatic pre-set revolution counter and one 7.5 kg weight, but without abrasive powder and thickness measuring device. Suitable for operation on 415 V, 50 Hz, 3 phase, AC Supply.

The machine is used for testing crushed slag, crushed and uncrushed gravel for resistance to abrasion. The aim of the test is to find the percentage wear due to the relative rubbing action between the aggregates and steel balls as abrasive charge. The oven-dried arrangements are weighted and rotated along with abrasive charge in the machine for the 500 or 1000 revolutions and percentage of wear so found out its reported as Los angeles abrasion value. General Description & Specifications: Consists of a hollow steel cylinder, closed at both ends, having an inside diameter of 700mm and inside length of 500mm. The cylinder mounted on a sturdy frame on ball bearings. The opening is closed dust tight with a removable bolted cover in place. A detachable shelf which extends through the drum catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated at a speed of 30-33 RPM by an electric motor through a heavy duty reduction gear. Fitted with revolution counter and push button starter. Supplied complete with a tray for collection of the material. Abrasive charge consists of set of 12 Nos. cast iron spheres or steel spheres (hardened steel balls) approximately 48mm diameter each weigh between 390-445 gram. Complete as above. Optional Accesories: The following accessories are not part of the standard supply and are supplied at an extra cost. Laboratory Oven. Test Sieve 1.7mm Electronic Balance of 15 kg x 1 gm Spare Abrasive charge.

Weight : 100-1000kg

Voltage : 110V

Rated Power : 1-3kw

Automatic Grade : Automatic

Driven Type : Electric

Production Capacity : 3000-6000 Per Day

Warrenty : 1year

Ours is a distinguished name in the industry that proffers accurately designed and developed Tile Abrasion Testing Machine that is given at affordable rates. Manufactured in adherence to the industry standards, these testing machines are used for the examination of abrasion resistance of tiles. Tile abrasion testing machines are available in safe packaging. Features: Efficient performance Corrosion resistant Tough construction Supplied complete with: Pre-set revolution counter and one 7.5 kg weight, but without abrasive powder and thickness measuring device   Specification Tiles specimen of size 7.06cm x 7.06cm is pressed tace-wise under specific load on a grinding path and abrasive powder is evenly spread on the rotating grinding path and after specific number of revolutions of the grinding disc the second parallel side of the tile is subjected to wear for similar number of rotations. The wear of the tile is measured on a thickness gauge specifically made fro the purpose. The machine consists of a disc rotating at a speed of 30 rpm in a circular tray. A bracket is provided to hold the specimen. A counter balance lever loads the specimen. Load applied is 30kgf. A funnel is fitted to evenly spread abrasive powder on the grinding path. The machine works on 440 volts AC, three phase electrical supply.

Colour Matching Cabinet, Toxicity Tester, galvanized iron cable tray

Elcometer 1720 Abrasion Tester, Elcometer 900 illuminated x50 Microscope