Cast Iron Three Piece Ball Valve
700 Per Piece
5 Piece(s) (MOQ)
Feature : Casting Approved
Application : Gas Fitting, Oil Fitting, Water Fitting
Weight : 10-20kg
Color : ELECTRO PLATING
Certification : ISO 9001:2008 Certified
Material : Alloy Steel, Carbon Steel, Stainless Steel, Cast Iron
Size : UP TO 12 INCH
Size : UP TO 12 INCH
Country of Origin : India
Condition : New
Pressure : Medium
Type : Three Piece Ball Valve
Name : 3 PIECE BALL VALVE FLANGED 150#
Cast Iron Globe Valve
2,000 Per piece
10 piece (MOQ)
Material : Cast Iron
Certification : ISI Certified, ISO 9001:2008 Certified
Application : Gas Fitting
Feature : Blow-Out-Proof, Casting Approved, Durable, Investment Casting
Brand Name : Nalisha
Pressure : 150
Tensile Strength : Strong
Temperature : -10 to +150 Degree C.
Cast Iron Globe Valve
1,500 Per Piece
Material : Cast Iron
Application : Water Fitting
Feature : Blow-Out-Proof, Casting Approved
Pressure : High, Low, Medium
Port Size : 0.1mm-5cm
Number Of Way : 2way, 3way, 4way
Cast Iron Butterfly Valve
500 Per Piece
Size : 25 - 450 mm
Type : Solid
Material : Cast Iron
Certification : ISI Certified
Application : Gas Fitting, Water Fitting
Color : Blue
Technics : Gear Operated
Pressure : Upto 15 Kg
Cast Iron Ebonite Rubber Lined Diaphragm Valve
3,900 Per Piece
10 Piece (MOQ)
Size : 15mm to 50mm
Media : Water /Oil / Steam / Air /Gas
Body : Cast Iron/ Cast Steel
Bonnet : Cast Iron
Wheel : Cast Iron
Diaphragm : Epdm / Ebonite Rubber
Operation : Hand Wheel Operated
Hyd Test Pressure : 10 Bar
Seat Test Pressure : 85PSIG, (6KG CM2 )
Temperature : 85 Degree C
Ends Connection : Flange End Table D /150# ( ANSI B 16.5 )
Cast Iron Butterfly Valve fully Lug Type
750 Per Piece
1 Piece(s) (MOQ)
Material : Cast Iron
Certification : ISI Certified
Cast Iron Strainer Valve
100 Pieces (MOQ)
Size : Available in Different Size
Material : Cast Iron
Application : Water Fitting
Feature : Casting Approved, Durable
Pattern : Plain
Pressure : Medium
Number Of Way : 2way, 3way
Cast Iron Foot Valve
300 Per Piece
1 Piece (MOQ)
Size : 50 MM TO 1000 MM
Material : Cast Iron
Country of Origin : Made in India
Brand : GLOBAL
I Deal In : New Only
Installation Type : Vertical
Manual : Yes
:
Cast Iron SS Disc Butterfly Valve
2,050 Per piece
01 Piece (MOQ)
Country of Origin : India
Type : Industrial Valves
Brand Name : UNIVERSAL
Material : Cast Iron
Certification : ISO 9001:2008 Certified
Color : Blue,Red,Sky Blue,White
Condition : New
Driving Mode : Hydraulic
Automatic Grade : Manual
Valve Size : 1.1/2inch, 2inch, 3/4inch
Size : 40MM TO 500MM
Cast Iron Butterfly Valve
10 Pieces (MOQ)
Material : Cast Iron
Application : Oil Fitting, Water Fitting
Feature : Blow-Out-Proof, Durable
Power : Manual
Number Of Way : 2way
Cast Iron Plug Valve
1,500 Per Piece
10 Piece (MOQ)
Size : Multisize
Material : Cast Iron
Application : Oil Fitting
Weight : 10-15kg
Feature : Blow-Out-Proof, Casting Approved
Pressure : High
End Connection : Screwed / Socket Weld / Flanged
End Connection Type : Flanged
Finishing Type : Polished
Automation Grade : Manual
Surface : Galvanized
Cast Iron Open Body Pinch Valves
Country of Origin : India
Size : 1inch, 2inch
Type : Ci Valves
Material : Cast Iron
Certification : ISO 9001:2008 Certified
Application : Gas Fitting
Color : Blue
Pattern : Plain
Pressure : Medium
Pinch valves, offered by our company, are the modified version of laboratory pinchcock in which rubber sleeve is protected under the casting made of cast iron. The main advantage of Pneumatic Pinch Valves is that the fluid passing from it does not come in contact with its metal parts except the sleeve. This property makes it corrosion resistive against the action of various fluids. Open Body Pinch Valves assure the smooth flow of water like pipeline and their collar sleeve eliminates gasket. Pinch valve is user friendly and can be operated easily as compared to other wheel operated valves. This valve allows positive control over flowing media because of its in between stoppage that gives desired throttling. These pinch valves are extensively used for handling corrosive slurry, liquid with solid suspensions, abrasive media, and many others. We offer pinch valve in best application range with flange as per BS, DIN, ASA & IS dimensions, and ranging between 15mm to 300mm. We are known widely as one of the proficient Pinch Valves Exporters and Suppliers. General Features & Highlights Seat Less & Glandless ValvesField Replicable Elastomer Sleeve.Elastomer Sleeve Having Four Reinforced LugsFlanged Ends & Drilled to Din, Ansi, Bs-10, Is, Etc.this Valve Incorporates allthe Design Modifications Based On Our Experience & is of Study Construction to Handle Abrasive Corrosive Media. BRIEF DETAILS OF PINCH VALVE Pinch Valve is a Seat less & Glandless valve.Pinch valve is a modified version of laboratory pinchcock. A rubber sleeve is protected under a cast iron casting.The fluid passing through do not come in contact with either body covering or any other metal parts of the valve except the sleeve.Hence the body and other metal parts are almost permanently not subjected to the corrosive action of the fluid.The flow through the valve is straight and full as that of a pipeline, when the valve is fully open. Further, the collar of the sleeve eliminates gasket.The valve is simple hand wheel operated of rising wheel type. Therefore the operation of the valve is just simple as other wheel operated valve.The in-between stoppage will allow the desired throttling. Thus the valve offers positive control over flowing media. Applications Pinch valve finds its best application in handling corrosive slurry, abrasive media, liquid with solid suspensions and many others, which are difficult to handle with seat valve. Range The flange of the pinch valve can be supplied in accordance to BS, DIN, ASA & IS dimensions The range for the valve is from 15 mm TO 300 mm. Actuation The valve can be supplied with Electrical and pneumatic actuation. Operating Manual OF PINCH VALVE THE PINCH VALVE is a modified version of the laboratory pinchcock. A rubber sleeve is protected under a Cast iron or Aluminum split body casting. The valve is a simple hand wheel operated of rising wheel type. The operation of the valve is same as other hand wheel operated valve, it closes when moved in clockwise direction and opens when moved in anticlockwise direction. The in-between stoppage will allow the desired throttling. Thus the valve offers positive control over flowing media. The flow through the valve is same as that of a pipeline, when the valve is in fully opened condition. Further, the rubber sleeve eliminates the need of a gasket. PRELIMINARY PRECAUTION On receipt of the valve please check the position of the valve, as it is advisable to keep the valve in fully opened condition. Also check the position of the travel limit nut, if found loose then tighten the set screw of the nut. INSTALLATION The valve can be installed without any gasket unless it is required for some specific purpose. Tighten the nut of the flanges evenly & equally, but avoid too much tightening. After installation check the free movement of the upper & lower pinching bar by opening & closing the valve. The valve is then ready for the service it is installed for. MAINTENANCE If the valve is found leaking through the seat after sometime even though in fully closed condition, then set the travel limit nut by just taking it 1 or 2 threads above & then tighten. This will allow more room for traveling of rubber sleeve & ensure the valve to zero leakage. This problem sometimes occurs when the sleeve is slightly worn out, when used under abrasive condition. Further, The Rubber sleeve of the valve up to 2” (50mm) have a single lug on either side and it goes into the hollow passage of the pinching bar where it is fixed with the lug clamping screws. In the higher sizes above 2” the sleeves have two lugs on either sides and is fitted overlapping the pinching bar. DISMANTLING THE VALVE & REPLACING THE RUBBER SLEEVE When the rubber sleeve is ruptured or totally worn out then it is to be replaced with a new one. In this case first dismantle the valve by following the instructions. Remove the hand wheel.Open the Tie Bar nuts.Disconnect the spindle from the Horseshoe connection and remove it completely with the bridge.REMEMBER not to temper the set screw of the yoke bush, unless if required it should be completely tight.Open out the nuts & bolts of the split body of the valve.Remove the screw of the lugs from both the pinching bars.Now fit the new rubber sleeve & reverse the operation to assemble the complete valve. NOTE It is advisable to keep a spare rubber sleeve for maintenance purpose, considering the self life of the Rubber as six months when packed & stored in dark. The Pinch valves should be stored in fully open condition only. We also offer complete spares of the valves, but request you to place your order a week in
Cast iron two piece ball valves
950 - 1,450 Per 5-6kg
50 5 (MOQ)
Material : Cast iron
Color : Dark grey
Application : Oil Fitting, Water Fitting
Size : 25-100mm
Feature : Good Quality
Weight : 5-25kg
Country of Origin : India
Condition : New
Pressure : High, Medium
Type : Two Piece Ball Valves
Cast Iron Gate Valve
4,500 Per Piece
Size : 21/2"
Material : Cast Iron And Also Available In Cast Steel, Stainless Steel
Corrosion Resistance : Yes
Technique : Hot Rolled
Packaging Type : Box
:
Cast Iron Butterfly Valves
From Ahmedabad(India), India, we delight our valuable patrons by providing quality-centralized products. Advanced transportation facilities, efficient workforce, on time delivery of the products make us stand out from the crowd.
Cast Iron Gate Valve
1,000 Per Piece
Media : Water
Material : Cast Iron
Brand Name : Radiant Flow
Automation Grade : Manual
Cast Iron Butterfly Valve
400 - 700 Per PIECE
5 Piece (MOQ)
Brand Name : MEGA VALVES
Material : Cast Iron
Power : Manual
Pressure : PN 10/16
Color : Blue, YELLOW
Application : Gas Fitting, Oil Fitting, Water Fitting
Technics : Gear Operated
Certification : ISI Certified
Feature : Casting Approved
Size : UP TO 24 INCH
Type : TEFLON
Media : WATER / OIL / GAS
Temperature Of Media : UP TO 180 D
Country of Origin : India
Cast Iron Sluice Valve
10,000 Per Piece
Material : Cast Iron
Pressure : High
Temperature Of Media : High Temperature
End Connection Type : Flange
Automation Grade : Manual
Ductile Iron Air Valves
9,494 Per
1 Piece (MOQ)
Country of Origin : Made in India
Color : Red, Blue, Black
Media : Water, Air
I Deal In : New Only
Usage/Application : Industrial
Surface Treatment : Color Epoxy Coated
Corrosion Resistance : Yes
Cast Iron Pulp Valve
6,000 Per unit
Size : 32 inch
Brand Name : Ambica Paper Machineries
Pressure : Low Pressure
Country of Origin : Made in India
Usage/Application : Industrial
Body Material : Cast Iron
Cast Iron Flanged Type Foot Valve
Material : Cast Iron
Type : Flanged
Surface Finish : Polished
No of Bolt : 6 Bolts
Cast Iron 2 Piece Flanged End Ball Valve
We are having with us finest range of Cast Iron 2 Piece Flanged End Ball Valve. We source the product from reputed manufacturers only and no compromise is made with the product quality. Superior quality cast iron is used for the making of the ball valves. Quality check is done for each batch of CI ball valve before dispatching to client location. Our distributed valves have long life and durability Installation of the ball valves can be done very easily The valves are designed carefully to deliver high performance The construction of the valves are robust and free from corrosion For more information on this product range and quotation connect with our representative online or over phone. We will be happy to assist you in all your requirements related to Cast Iron 2 Piece Flanged End Ball Valve. Delivery will be done in sealed damage proof packs.
Cast Iron Butterfly Valve
2,550 Per
1 Piece (MOQ)
Material : Cast Iron
Feature : Blow-Out-Proof, Casting Approved
Media : Water
Country of Origin : Made in India
Valve Size : 150 mm
Connection Form : WAFER / FULL LUGGED
Usage/Application : AIR, WATER
Operation Type : By Lever, By Gear, By Actuator
Cast Iron Swing Valve
Size : 15 MM TO 300 MM
Brand Name : ALIS
Material : Carbon Steel
Color : BLACK
Type : SWING CHECK
Country of Origin : Made in India
Media : Water
Model Name/Number : ASCV
Connection Form : F/E
Structure : CHECK VALVE
cast iron gate valves
1,000 Per
1 Piece(s) (MOQ)
Country of Origin : Made in India
Size : 2
Temperature Of Media : High Temperature, Medium Temperature, Low Temperature
Brand : Aqua
Usage/Application : Water, Steam , Oil , Chemicals
Cast Iron Gate Valve
2,000 Per Piece
10 Piece (MOQ)
Material : C.I / C.S / SS 304 / SS 316 & More
Size : 1/2
End Connection : Screwed / Socket Weld / Butt Weld / Flanged End
Temperature Of Media : High Temperature, Medium Temperature, Low Temperature
Automation Grade : Hand Wheel Operated
End Connection Type : Screwed / Socketweld / Flanged End
Cast Iron Gate Valve
5,000 Per Piece
5 Piece (MOQ)
Material : Cast Iron
Pressure : Medium Pressure
Media : Water
Size : 15mm
Usage/Application : Industrial
Valve Size : 90mm
End Connection Type : Flanged
Brand : Ashok
Cast Iron Globe Valve
Size : 12” to 4”,Applications : Water, Steam, Oil & Gas,Temperature : 200° Centigrade in Working Condition,Pressure : 25 Kgcm² in working condition,Design : ISO 5752 Class 150, BS 5159 Table 2, ANSI B 16, BS 21, API 5B,Guarantee : 12 months replacement guarantee.
Cast Iron Foot Valve
50 Per Kilogram
Material : CI
Application : Pipe Fitting
Surface : Coated
Cast Iron Valves
We are well known manufacturer and exporter of cast iron valves with great functional values. Our high tech manufacturing facility allows us to serve the purpose of fabrication of high quality valve series with all modern features. Involvement of advanced technology reflects in valve quality. Our series of cast iron valves are efficiently used in industries like petroleum, sewage treatment plants, refineries, domestic water systems and chemical industry. We offer cast iron gate valve, cast iron globe valve, cast iron check valve and also other cast iron valves as per need of operations. Entire cast iron valve series is built as per international standards. It possesses robust construction to withstand all demanding conditions. Our cast iron gate valves are specially designed to offer minimum pressure drop in system. It is provided with solid wedge. It offers fully closed or fully open conditions. So, it is used to provide least flow resistance. Cast iron gate valves are preferably used for varied industrial activities of air and liquids. It is available with size range of 2” to 48” with pressure class of 125-250. It is available with non rising stem and outside screw design. It is constructed with ASTM A 126. Our range of cast iron globe valve is specially fabricated for throttling and regulating applications and effectively used for vapor, liquid, and gas. It is used for the fully opened, fully closed applications. It is also used for partly open/closed application need. We also offer custom valve with precise configuration.