Knife Gate Valves Dealers in Odhav, Ahmedabad (36 products available)

Brand Name : Allines

Feature : Bi-directional shutoff, high strength, durable life and resistance towards corrosion etc.

Place of Origin : Ahmedabad  

Grade : High

Packaging : Bulk

Condition : New, Good

The company holds expertise in manufacturing, exporting and supplying high grade Sand Casting Heavy Duty Slurry Knife Gate Valve. The Sand Casting Heavy Duty Slurry Knife Gate Valve, offered by us, facilitates flexible pressure assisted two-piece rubber sleeve system which allows valve to cycle in heavy slurries without sticking. The sleeves of our Sand Casting Heavy Duty Slurry Knife Gate Valve can be easily replaced without disassembling the valve. In addition to this, the bi-directional full port flow reduces pressure drop and turbulence, thus minimizing wear. The open bottom of our Sand Casting Heavy Duty Slurry Knife Gate Valve allows for the purging of large solids, and solids in higher concentration. The purging of solids stops when the gate is in the full open or closed position. Our Sand Casting Heavy Duty Slurry Knife Gate Valve is highly appreciated by the clients for high strength, durable life and resistance towards corrosion. Features : New and replaceable upper seal design is not only packing less, which eliminates the need for periodic adjustment, it is also a self lubricating system and is rechargeable without valve disassembly Open bottom allows for the purging of large solids, and solids in high concentration Bi-directional shutoff Sleeves are available in a variety of materials to handle abrasion, and chemical application Flushing plate option allows for periodic cleaning of the lower discharge vent and allows flushing as needed Two-Piece Rubber Sleeve System : Port pressure provides assistance by forcing the sleeves against the opposing sleeve or the gate, depending on the position, to provide greater sealing force. Face rings allow the valve to cycle under maximum flow conditions up to a maximum differential of 150 psi10 bar. Seats are self gasketing and are compatibility with raise face.Flushing Cover Bonnet : Flushing Bonnet attached to the bottom flange to capture any discharge during cycling. This option also allows for periodic cleaning of the lower discharge vent and can allow flushing as needed. It has a bi- directional shut – off design.

Disc A 240 SS 304 316, Yock ASTM A 216 GR. WCB, Thrust Washer BRASS, Seat O - Ring NBR, Bearing Housing ASTM A 216 GR. WCB CF8 CF8M, Wheel Nut STEEL, Bearing Housing Bolt STEEL.

Available Sizes : 3"-36

Features Abrasivion-Resistant Slurry Sleeves are FieldReplaceable, Provide Bi-directional, Drop-Tight Shut-off and Eliminate the Need for Packing100% Full-Port DesignHeavy-duty 316L stainless Steel Getwiper Blade Cleans debris from Gate as it strokesOpen/Close Lock-Out feature (optional)Robust Corrosion-Resistanct ductile iron yokeGrease Fittings for Gate and Stern Lubrication is Ductile Iron. SS 304, SS 316, SS 316L, Alloy 20, CD4MCu available on request.     Application :     Powder handling in silos Pulp and Paper Plants Slurry Handling(Chemical Plant & Process Industries) Water and Sewage Applications Pneumatic Conveying Systems High temperature services Mining & Power Plants

We are offering knife gate valves, jupiter controls knife gate valves is greatly appreciated for its cost effectiveness. This series is developed with an aim to enhance customer's profitability and satisfaction. features knife gate valve is one of the most preferred industrial valves. It is featured with minimum contact between moving parts of the valves. In this type of valve, a gate is practically held between layers of gland packing without touching the body parts during most of its travels. the seating is accomplished with a non-sliding motion aided by jams located in the body. Avoiding sliding contact between gate and body permits this valve to handle abrasive particles present in the media much better than conventional designs. This valve is named 'knife' because of the beveled bottom edge of the gate. It allows positive closure of the gate even when solid particles settles at the bottom of the body. In abrasive media, deflection cones are used to avoid direct impingement of the media on the seat surface. Besides this, sometimes hard facing of seat part is also used, which involves stelliting of the seat or gate or complete intruding of body as well as gate. Another feature is the purge connection which allows the flow of suitable fluids at pressures higher than line pressure in order to clean seating surfaces (body purges) and packing area (chest purges). This helps in minimizing abrasive wear and tear during opening and closure of valve. Knife gate valves are excellent hopper isolation valves with their ability to cut through flowing powders and close by dislodging any material in the seating area. Specially designed to tolerate differential thermal expansion of its parts without affecting its functions, this valve is an ideal choice for handling high temperature media,

Material : Carbon Steel

Application : Water Fitting

Weight : 10-15kg

Feature : Casting Approved, Corrosion Proof

Pressure : High, Low, Medium

End Connection : Butt Weld, Flanged, Screwed

Material : Carbon Steel / Stainless Steel / Other

Type : Uni - Directional / Bi - Directional

End Connection : Flanged End / Wafer Type / Lug Type

Feature : Long Life Span

Operation : Hand Wheel / Pneumatic Actuator / Cylinder / Electric Actuator

Size Range : 50mm to 1200mm

Backed by a hardworking team, we are capable of offering the Knife Edge Gate Valves as per the exact requirements of the buyers. Our effective and excellent quality analysis helps us in delivering the best in class range of products.

Knife Edge Gate Valve is the specific design. This design ensures minimum contact between the parts of the Valve, Reduces the Wear & Tear. The high-performance Knife Gate Valves feature. Non-Sliding Motion, Avoid Sliding Contact between Body & Gate allow flushing of media form the Valve interior. A wide variety of hardened trim options are available on Gate, Seat and Wear Ring. Batten edge of the Gate (Knife-Edge) allows the tight shut off even when solid particles settles at the bottom of the Body. The valves are regularly used for applications to handle, pulp in pulp mill, slurries, powder such as coal, ash, dry and wet powder in power houses, pneumatic conveying systems, dust collecting systems and material handling equipment’s. For liquid slurries and fiber applications with low-allowable leakage the valves are most commonly used. Pneumatic, Manual, Gear and Hydraulic equipment devices are provided for operation of the Valves. For elevated mounting, chain driven Valves are also provided. Our product range covers valves of sizes up to 36” [900mm] and ASME classes up to 150, PN 10 and PN 16. Based on customer requirements, valves in different pressure classes, larger sizes and other materials are also offered. We manufacture this Valve according to MSS SP – 81 designing and manufacturing standards. Uni-directional Type Knife Gate Valve Bi-Directional Type Knife Gate Valve Square & Rectangle Type Knife Gate Valve Fabricated Type Knife Gate Valve

Size : 50 mm to 300 mm

Material : Stainless Steel

Pressure : Medium

Feature : Casting Approved, Durable, Good Quality

Valve Size : 4",6",8"10",12"14",16",20"

Power : Hydraullic

VQ Knife Edge Gate Valve is an Uni-directional/Bi-directional lug type valve designed according to MSS-SP-81 for industrial service application. That is Supplier & Manufacturer of Knife Edge Gate Valve. The Design of the body & seat assures non-clogging shut off on suspended solids.

Type : Uni-directional / Bi-directional Knife Edge Gate Valve

Size : 50mm T0 800mm (higher size on application)

Port : Round Port, “V” Notch, Square Port.

MOC : Cast Iron / Cast Steel / SS 304 / 316 / 304L / 316L.

Gland Packing : Multi layer gland packing in a variety of materials to suit condition provides total sealing.

The knife edge gate valve is specially designed industrial valves, which makes sure that there is minimum contact between the valve parts which helps to reduce wear & tear. Usually the knife gate valves are unidirectional and act as a brilliant hopper isolation valves as these valves have the ability to cut through flowing media and closed by dislodging any material in the seating area.

Knife Gate Valves are exclusively designed and manufactured as per MSS SP-81 to tackle the tough working conditions in Pulp & Paper, Mining & Steel, Power and Chemical Industries to deal with Semi-Solids, Fly Ash, Chips, Iron Ore, Tea and Coffee powders, Food Products like chips and mixtures, Sugar and Sugarcane Juice, Fiber content Pulps and similar media. The Knife Gate Valves are offered in an extensive range of Material where as its Knife edged Plate is made of from Stainless Steel Plates of different grades irrespective of the Body material, Hard Faced Plates to suit the application. During shutting operation of the Knife Gate Valve the Knife edged Plate cuts off the solids and allows the plate to seal properly.

Features STARTEK Knife Gate Valve (Manual Operated) Nominal pressure : 0.6MPa, 1.0MPa,1.6MPa, 2.5MPa, 150Lb Nominal diameter : DN50-400mm NPS 2"-16" Suitable temperature :-38-+650°C(Rang of temperature subject to the material of sealing and property of medium) Connecting flange : ANSI B16.5, GB/T9113, JB/T79, HG, SH, JIS, DIN, NF, BS. Main materials : WCB, ZG 1Cr 18Ni9Ti, ZGICr 18Ni12Mo2Ti, CF8, CF8M, CF3, CF3M Seal type : Stainless steel hard seal : Teflon soft seal Leakage : Stainless steel hard seal : Grade D (Liquid 0.1XDN me/S) Teflon soft seal : Grade A (Zero Leakage) Accessories : Flange Part Name Material Option Body   ASTM A216 WCB / A 351 CF8 /A351 CF8M / A351 CF3 / A 351 CF3M / CAST IRON Yoke   ASTM A216 WCB / A 351 CF8 /A351 CF8M / A351 CF3 / A 351 CF3M / CAST IRON Yoke Sleeve   SG IRON Gate   AISI 304 /AISI 316 Spindle   AISI 304 /AISI 316 Gland   ASTM A216 WCB / A 351 CF8 /A351 CF8M / A351 CF3 / A 351 CF3M / CAST IRON Seat Ring   AISI 304 /AISI 316 Yoke Bush   Carbon Steel Hand Wheel   M. I. Hand Wheel Nut   Carbon Steel Gasket   Asbestos / PTFE Stud & Nuts   Carbon Steel

We are renowned as one of the trusted Industrial Knife Edge Gate Valve Manufacturers and Suppliers in India. The use of optimum quality raw materials in the manufacturing of the Knife Edge Gate Valve ensures inexplicable performance in respective applications. Moreover, high durability, tensile strength and resistivity to rust have also played a vital role in the enhancement of the demand of Knife Edge Gate Valves.

Maruti valves offers a tremendous markdown on purchasing for knife edge gate valve in india, uae, dubai, saudi arabia and south africa. For more data about our administrations you can visit us online whenever.

Brand : ANUSHKA

Size : 1/2 Inch to 12 inch

Material : Stainless Steel

Model Name/Number : 10111000

Valve Size : 1/2 to 4 inch Screwed End,1/2 to 12 inch Wafer Type,1.1/4 to 2 inch Lug type

Temperature : Max. 300 Degree C

Country of Origin : Made in India

Size : 80 mm to 700 mm

Cylinder Type : Double Acting / Single Acting

Body : DCI /ASTM A 216 Gr WCB/CF8/CF8M

Gate : A 240 / SS 304 / 316

Yoke : ASTM A 216 Gr WCB- Epoxy Coated

Seat : Metal,EPDM,Nitrile

FFV offers Double Acting / Single Acting Pneumatic Cylinder Operated Knife Edge Gate Valve.   Features FFV Make Knife Edge Gate Valve Can withstand high temperature Sturdy construction Corrosion resistance suspended solids & slurry knife ‘shaped’ to allow for precise flow control at low flow rates   Design & Inspection MSS SP-81 Hyd-Test Press: Body 11 Kg/Cm2 & Seat 2.8 Kg/Cm2 Flange Dimension: ANSI B 16.5 ( But SIZE 22″ & LARGER: MSS SP-44)

Knife Gate Valve mostly uses to handle powder; high viscous or slurry type thick media service to cut throughout and close the valve. Nivz Valves & Automation is Knife Gate Valve manufacturers and exporters in Unidirectional and Bi-Directional type, Rising Stem and Non-Rising Stem with Metal to Metal Seat & Soft Seat which mostly use in service of Isolation and On-Off service. The valve sliding plate (gate) has knife edge, so it is called Knife Gate Valve or Knife Edge Gate Valve which both are same. Previously it was mostly use in service of Powder, Slurry, Pulp and Paper Mill now it use in many more industrial applications. Some user also asks for Slide Gate Valve in place of Knife Edge Gate Valve. Nivz Valves & Automation and leading manufacturer and exporter of valves to Dubai, Kuwait, Kingdom of Saudi Arabia, Jeddah, Jubail, Malaysia, Thailand, Singapore, Australia, Brazil, Italy, Romania, Azerbaijan, Sharjaha, Abu Dhabi, United Arab Emirates, Egypt, Turkey, Sri Lanka, Yemen, Pakistan, Bahrain, Indonesia, Zambia, Uganda, Netherlands, Philippines, Vietnam, Dominican Republic, Oman, West Africa, Finland and Jordan. Knife Edge Gate Valve has very simple construction and assembly is with very few parts like Body, Knife Gate, Seat, Gland Flange, Gland Packing and Yoke - Bonnet Assembly. Each knife gate valve body design is single piece casted heavy duty construction, slide gate plate grinded with lapped and seat integral with body or renewable type as customer request.   Knife Gate Valve use of application in Corrosive Service, Pulp - Paper Mill, Abrasive Slurry, Power Plant, Steel Plant, Mining & Mineral Plant, Dry Material Handling, Sugar Mill, Cement Industries, Waste Water Treatment Plant, Process Chemical Plant and others. For more detail specification data sheet, technical data sheet, cross section drawing, product catalogue, operation and maintenance manual of Knife Edge Gate Valve contact us. Nivz manufacture knife gate valve with Manual Hand Wheel Operated, Pneumatic Cylinder Operated, Motorized Actuator Operated, Electrical Actuator Operated, Hydraulic Cylinder Operated, Worm Gear Operated and Chain Wheel Type Gear Operated. Knife Edge Gate Valve Material of Construction Body Design – Unidirectional and Bi-Directional (flow can be from either or side) Body Construction – Single Piece Casted, Rugged, Heavy Duty  Knife Gate – Knife Gate Plate supply in Stainless Steel (S.S.) 304/316/304L/316L, other special grade on request. Knife Gate both side fully machined, grinded, buffed and lapped at seat contact side with beveled edges to extend life of Gland and Seat. Stem – Single Piece from heavy duty round bar with quality square thread and brass or gun metal stem nut to extend life of stem. Seat –   Integral Metal to Metal seat as per MSS SP-81 Standard Renewable Type Seat: Elastomer, Rubber Seat (NBR, EPDM, Nitrile, Neoprene, Viton, Silicon Rubber O-Ring) Renewable Type Seat: PTFE (Teflon) Soft Seat Deflection cone with Stellite Hard Face – F6  Port Opening – Full Round Port / V – Notch Type

End Connection : WAFER TYPE, FLANGE LESSSUITABLE TO MOUNT BETWEENANSI B 16.5/BS 10/DIN/IS FLANGE

DESIGN STANDARD : MSS SP 81

INSPECTION & TESTING STANDARD : MSS SP 81

FACE TO FACE : MSS SP 81

SIZE RANGE : 3" TO 24"

PRESSURE RATING : 150#

OPERATION : HAND WHEEL / GEAR / PNEUMATIC /ELECTRIC ACTUATOR OPERATED

We are leading best Knife Edge Gate Valves supplying company.

Country of Origin : Made in India

Size : 32 inch

Brand Name : Ambica Paper Machineries

Body Material : Cast Iron

Usage/Application : Industrial

Working Pressure : 10 Bar

Surface Finishing : Powder Coating

Stainless steel cladding knife gate valve is an uni-directional for industrial service applications this body and seat assures non-clogging shut off on suspended solids in industries.

Knife Gate Valves are exclusively designed and manufactured as per MSS SP-81 to tackle the tough working conditions in Pulp & Paper, Mining & Steel, Power and Chemical Industries to deal with Semi-Solids, Fly Ash, Chips, Iron Ore, Tea and Coffee powders, Food Products like chips and mixtures, Sugar and Sugarcane Juice, Fiber content Pulps and similar media. The Knife Gate Valves are offered in an extensive range of Material where as its Knife edged Plate is made of from Stainless Steel Plates of different grades irrespective of the Body material, Hard Faced Plates to suit the application. During shutting operation of the Knife Gate Valve the Knife edged Plate cuts off the solids and allows the plate to seal properly.

Application : Isolation

Size : 50 MM TO 600 MM

Features / Benefit : OS & Y Construction Renewable Seat Rings Burnish Finish Stem for Low Operating Torque

Ansi Class / Rating : 150#/PN 10

Design Standard : MSS SP 81

Testing Standard : ISO 5208

F to F standard : ASME B16.10

Knife edge gate valve is engineered from finest quality components and under the strict supervision of expert quality controllers. These are available in various technical specifications and widely used in various industries for unobstructed flow of liquid or air. Engineered by implementing best available techniques, these products are widely acclaimed for high functional efficiency and longer service life. These are one of the most preferred selections of clients owing to its high tensile strength, robust design, longer functional life and precise design. These are compact in size and acclaimed for durability and rough and tough usage. Its OS & Y construction make these extensively efficient. These are extensively acclaimed for its corrosion resistance and uninterrupted performance. These are available in all standard sizes including 50 MM TO 600 MM. these are designed with MS SP 81 design standard and API 598, testing standard for flawlessness.

Knife Edge Gate Valve, Safety Relief Valves, gas, Gate Valves

Knife Edge Gate Valve, GLOBE VALVE, FLANGED END, Jacketed Valve

Knife Edge Gate Valve, Knife Edge Gate Valve, Non Slam Check Valve

Knife Gate Valves, Gate Valves, Swing Check Valves, Butterfly Valves

Knife Gate Valves, Industrial Valves, Cast Iron Double Flange Sluice Valve