Mounting Press Dealers in Ambala (13 products available)

• Digital Hot Mounting Machine: Table Tap

Automatic metallographic specimen mounting presses a kind of full automatic mounting press, equipped with in-out water cooling system. It is suitable for the heat mounting (thermohardening & thermoplastic) for all kinds of materials. After the parameters such as heating temperature, heat preserving time and applied force etc. are set up, put the specimen and mounting material into the machine, close the cover and press the start button, then the machine will finish the job automatically. It is not necessary for the operator to be on duty. According to different requirements of the material, there are four kinds of moulds that can be chosen to meet the demands at will. Also it is available to prepare two pieces of specimens at the same time, the capacity is doubled.

• Country of Origin: India
• Type: Digital
• Condition: New
• Brand Name: Almicro
• Power: 1.5kw-7.5kw
• Voltage: 220 V
• Automation Grade: Automatic

SPECIMEN MOUNTING PRESS (DIGITAL) - MODEL-MMP10 This machine is used for mounting the specimen with bakelite powder and also to handle properly without the conduction of heat to the operator while grinding/lapping the specimen. It also helps for proper alignment while using with microscopes. This machine will also help to reduce the recurring cost of consumable drastically unlike using cold setting compound. This machine comes with powder coating finish for corrosive free life This Model of Specimen Mounting press is big in size, and comes with heavy tonnage hydraulic jack, digital temperature controllor and timer.

We are offering specimen mounting press. Xq-1 is manual mechanic mounting press with 3 different size of mounting mould. Temperature and heating time can be setup and shown manual on the panel.

Vaiseshika’ Offers Mounting Press, the next step is mounting after Cutting the specimen. The aim of mounting is to handle small or odd shaped specimens and to protect fragile materials, thin layers or coating during preparations as well as to provide good edge retention. Mounting produces specimens with uniform size so that it is easier to handle while analyzing them.           Basically, two methods are available :       HOT MOUNTING                COLD MOUNTING In hot mounting, The specimen is mounted under heat and pressure with a hot mounting press. Cold mounting is preferred for samples which are sensitiva to damage from heat and pressure (like coatings, PCB etc.) Cold mounting resins are easy to use and require mixing which is then poured into a mould and allowed to set.

• Model: HV-EXP3755

This machine is used for mounting the specimen in a Bakelite Powder and also to handle properly the specimen during polishing. The unit is of a rugged construction and is activated by a hydraulic press , with a pressure gauge to read the pressure being applied while mounting. The press is to be supplied complete with mould heater and thermostat with 25 mm dia mould assembly..

• Brand Name: VAISESHIKA

we are offering vaiseshika specimen mounting press. description xq-1 is manual mechanic mounting press with 3 different size of mounting mould. temperature and heating time can be setup and shown manual on the panel. specification mould diameter 22mm, 130mm, 145mm input voltage 220v50hz, 110v60hz. power max. 650 w dimension 340x260x430 mm (approx.) weight 33 kg (approx.) for our complete product range.

• Model Number: Jlab7723
• Brand Name: Jlab
• Place of Origin: India

Automatic Mounting Press for metallographic specimen. It is suitable for all Thermosetting Materials, because of the cooling system. It has automatically cut-off in heating temperature, the holding time and acting force. The operator can change 4 specification patterns according to the difficult specimens. It can make 2 specimens at one time. Specification Design specimen : 25mm, 30mm, 40mm, 50mm Power: 220V 50Hz Maximum consumption: 1800W Pressure: 0~2Mpa Temperature: 0~300 deg. C Farm time: 0~99minutes and 99 seconds Outer Body measurement: 615 x 510x 500mm Weight: 100Kg--130 Kg Cooling Source: Water cooling.

• Size: 73x41x24mm .

Mounted Specimen, Insect Gives Students An Up Close Study Of This Unique Creature Encased In Clear Acrylic.

Hot Mounting Press is designed user friendly for efficient and quality production of the specimen mounts. The Press has rigid construction complete enclosed body and elegant look. Design of the heater, operation ease, good quality hydraulic integrated jack. One can produce absolutely consolidated embedded single specimen mount with good finish, out of this mounting press. This machine has manual operation with lever.   FEATURES: Higher results in measuring Image Analyses study. Temperature controller for setting heat cycle. Timer System for completion of process. Thermocouple Inside for indication of heat produce. TECHNICAL DETAILS : Product Metallurgical Hot Mounting Press Operation :- Manual with lever Mould Diameter :- 25 mm Heater :- 750 Watts Hydraulic Jack :- 6-8 Tons Thermocouple :- 1 No. Temp. Range :- 0-300° C

We are offering metallographic specimen mounting press.this machine is used for mounting the specimen in a bakelite powder and also to handle properly the specimen during polishing. The unit is of a rugged construction and is activated by a hydraulic press , with a pressure gauge to read the pressure being applied while mounting. The press is to be supplied complete with mould heater and thermostat with 25 mm dia mould assembly.

specimen mounting pres, Digital Moisture Balance, specimen polishing machine

Metallography Specimen Mounting Press, Floating Carriage Diameter Micrometer

specimen mounting press, Digital Cereal Grain Analyzer, MCT Twin Rack