Electric Actuators Dealers in Bangalore (65 products available)

• Voltage: 12/24V DC
• Ambient Temperature: -5
• Duty Cycle: 10% Max, 2minutes on/18 minutes off
• Stroke Length: 150 mm
• Speed At Rated Load: 4
• Brand: Bibus
• Protection Class: IP 54
• Thrust: up to 6000N

We manufacture Hydraulic Linear Actuator for 90º, 180º, 270º and 360º rotary movement with Hollow Spindle, Shaft Output, Spline with Coupling Model etc., Torque ranges available from 400Nm to 5400Nm.

• Type: Electric Linear Valve Actuator
• Country of Origin: Taiwan
• Model No: ML7420A6033 E
• supply voltage : -: 24 Vac ±15%; 50/60 Hz
• power consumption :-: 5 VA
• run time at 50 Hz :-: 1 min
• close-off force: :- ≥ 600 N

Model No : ML7420A6033 E   Product Type : Electric Linear Valve Actuator  supply voltage : - 24 Vac ±15%; 50/60 Hz   power consumption  :- 5 VA    signal input 0(2) Vdc   :- Actuator stem retracted. Two-way valve:”open”, three-way valve port A-AB:”closed” . run time at 50 Hz  :- 1 min   Manufacture : Honeywell     Usage : Indutrial Automation     Warranty : 1 Year   Origin : MADE IN TAIWAN

Rotary Actuators are devices for converting the pressure energy in a fluid medium to useful rotary power. The rotary motion is usually limited to one revolution or less and hence they are also known as partial rotation motors or oscillators. “Tornado” Rotary Actuators are of Vane type design and Standard Models are available with upto 250.0 Kg.M. Torque at a maximum operating pressure of 70 Bar with a 250° angle of actuation. This design, with just a single moving part gives a long and trouble free service life with zero backlash. It is one of the most economical and compact devices in the market to generate very high torque, and zero back lash allows for very precise positioning at any position within its actuation angle.External stops will be required to stop and hold loads at desired positions and deceleration of high intertia loads shall be achieved through proper meter out circuits. The main features of these actuators are: Single moving part design Durable Trouble free service life with zero backlash Economical Compact in size Generates high torque Precise positioning at any point within its actuation angle The major applications are: Material handling equipment Rubber machinery Heavy door operation Special purpose machines Robotics Valve actuation Wire forming machinery Automation Indexers Manipulators Mobile hydraulic applications Machine tools Pipe bending machinery We provide customised solutions for individual applications based on the specific operating parameters demanded by each application.

Solid strength with delicate ease – with it’s construction height of just 7 cm the new Slimdrive SL NT can be almost invisibly integrated into the façade and can move leaf weights up to 125 kg. The new GEZE Slimdrive SL NT automatic sliding door system is ideal, particularly in glass façades. Product features: The guide rail is also new and can be easily fixed directly to the wall, façade or support beam Simple commissioning, service and door monitoring via the Service Terminal ST 220 or a computer with GEZEconnects and Bluetooth (see ServiceTools) Linear Sliding Door Slimdrive: Simple installation and servicing thanks to the front accessible roller carriages SL NT-FR: Redundant drive for escape and rescue routes with low- wear two motor technology Intelligent digital control (Category 2 according to DIN EN ISO 13849-1): Automatic learn programme Dynamic adjustment of the hold-open time for through-traffic for optimal comfort Compatible and integrated in the building technology management system via CAN-Bus Independent error recognition and protocol Settings for all door movement parameters Integrated short circuit proof for all operation and actuation devices All functions are integrated into one device, no additional modules are required Extremely quiet running direct current drive with low-wear maintenance free motor Integrated battery for fully functional operation in power failures (temporally limited according to battery capacity) and subsequently programmable emergency function Robust power supply unit with integrated multi-pin mains switch and safeguarding Certified according to DIN 18650

Electric linear actuator Linear actuator is an electrically operated device which help push or pull objects. These actuators can handle a lifting capacity of 200 – 12,000 Newton. They are quiet, safe and has a clean and accurate motion control. Linear actuators are widely used for applications like hospital bed, dental chair, ICU beds, OT tables and so on. Because these actuators are easy to install and required no maintenance most hospital bed and furniture manufactures prefer these actuators. Talk to BIBUS INDIA sales team with your requirement. We will help you choose the right linear actuator for you.      General Features Input: DC, 12V / 24V Duty Cycle: 10%, Max 2min. Continuous use Protection class: IP54 Limit Switch: Built-in Overload protection: Yes Construction: Permanent Magnet

• Valve Motion: Linear Motion Valve
• Phase: Three Phase
• Actuator Type: Linear Actuator
• Brand Name: Aventics
• Structure: Control
• Speed At Rated Load: 8.9 in/min

A Electric Linear Actuators is a hardware which creates the movement along a straight line, in contrast with the rotary motion of a conventional electric motor. The linear actuator is used in automation, automotive (such as management carburetor, moving lights), in computer peripherals (disk drives and printers), valves and other areas of application where there is a linear motion.   Electronic driver for 1 or 2 independent actuators or 2 synchronized actuators 12/24V 10-15AFeatures : Driver power stage with pulse width modulation (PWM) Customizable acceleration and deceleration ramps Extreme precision and control for movement and brake Current and temperature limits Stop with limit switches Parameters editable in an easy and fast way thanks to a PC interface and through a USB serial converter Control of movements in synchronous mode by encoders with Hall effect; setting of the electronic limit switches (opening/closing) Compatible with a wide range of products and different applications High efficiency and low losses of power stage It is designed as electronic driver in low voltage for the control of one or two linear actuators with DC motors through MOSFET transistors with pulse width modulation (PWM). In “sync” mode, the driver ensures the balancing of actuators also in case of extremely different loads in terms of weight, shape,or distribution on the surface, allowing a stroke without any difference between the two actuators.Technical Data : Power supply: 12 to 48 V DC, maximum ripple 20% Output current: 15 A for motor, in duty cicle S3 - 30% - 10 minutes PWM frequency 10 kHz Stand by power consumption: 50 mA @ 24 V 12 digital inputs (3 - 12 V): 8 for commands/limit switches, 4 for encoders (max 1 kHz), with operating logic programmable (positive/negative) 2 digital outputs NPN open collector (max 50 mA - 24 V): one for the fault and one programmable Dimensions : Without heat sink for currents up to 10 A: 86x72x30 mm (WxHxD) With heat sink for currents over 10 A: 86x72x50 mm (WxHxD) Signal Terminals (Vertical) Open: opening command Close : closing command Trim-1 : enabling independence for actuator 1 Trim-2 : enabling independence for actuator 2 OP-SW: opening limit switch CL-SW: closing limit switch INT-SW: intermediate limit switch Stop Encoder motor 1 – channel 1 Encoder motor 1 – channel 2 Encoder motor 2 – channel 1 Encoder motor 2 – channel 2 Digital output 1: Fault Digital output 2: programmable GND for commands, limit switches and encoder +12V for encoder supply Power Terminals (horizontal) +V: positive supply 0V: GND : M1+: actuator 1, positive supply (voltage > 0 opening) M1-: actuator 1, GND M2+: actuator 2, positive supply (voltage > 0 opening) M2-: actuator 2, GND Main Controls Open/Close: synchronous movement Trim1 + Open/ Close : movement of actuator 1 Trim2 + Open/ Close : movement of actuator 2 Trim1 + Trim12 (3 sec): homing Homing : The driver moves both the actuators in the same direction, according to an adjustable profile, amperometric threshold (controlled mechanical stop) or limit switches, depending on the configuration. It detects automatically the connection’s direction of encoders   Trimming : The driver moves each actuator independently, for mechanical adjustments and a first manual alignment. It is required to check that commands correspond to the direction of movementPossibility to configures on/off delays and reverse the logic. The start is provided through fully adjustable voltage ramps. The stop is provided through electronic limit switches (or eventually mechanical limit switches), or with adjustable current limits. Signal Terminals (vertical) : Open-1: opening command for actuator 1 Close-1: closing command for actuator 1 Open-2: opening command for actuator 2 Close-2: closing command for actuator 2 OP-SW-1: opening limit switch for actuator 1 CL-SW-1: closing limit switch for actuator 1 OP-SW-2: opening limit switch for actuator 2 CL-SW-2: closing limit switch for actuator 2 INT-SW-1: intermediate limit switch 1 INT-SW-2: intermediate limit switch 2 Stop-1: stop for actuator 1 Stop-2: stop for actuator 2 Digital output 1: FAULT Digital output 2: programmable GND for commands, limit switches and encoder +12V for encoder supply Power Terminals (Horizontal) +V: positive supply 0V: GND : M1+: actuator 1, positive supply (voltage > 0 opening) M1-: actuator 1, GND M2+: actuator 2, positive supply (voltage > 0 opening) M2-: actuator 2, GND In case of one or two independent actuators : It is possible to use intermediate limit switches It is possible to configures on/off delays and reverse the logic The start is provided through fully adjustable voltage ramps The stop is provided through mechanical limit switches, limit switches for overcurrent or adjustable current limits Main editable parameters: Voltage ramps Current limits Synchronous or independent enablement Homing at the start (for sync only) Homing with current limits or limit switches (for sync only) Virtual limit switches settled with encoder pulses limits (for sync only) Values monitorable through “Monitor” and “Statistics” sections : Motors current Applied voltage Temperature Speed Active commands Operating mode General information about the operating status of the driver Using the PC interface, it is possible to : Consult the errors history (the driver stores each error and the time at which it occurred, from the last start) Decide if an error stops the operation (only advanced mode for some errors) Decide after how many repetitions of the same error the driver has to block (only advanced mode for some errors) Decide the error tripping delay (only advanced mode for some errors) The connection driver/PC is possible through an USB/UART cable converter.

• Supply Voltage: 230VAC
• Duty Cycle: 230V-25% to 50%

Bossmanfilter Electric actuator designed for load requirements of up to 2500Nm. The actuator comes standard with two auxiliary switches (shared common, rated at 3A 250V Max), and in 12VACDC, 24VACDC, 120VAC or 230VAC supply voltages.

• Features: Shear strength, Rugged design, Reliable operation

• Pressure: High Pressure, Low Pressure, Medium Pressure
• Voltage: 24 V DC
• Stroke Length: 4",5-29/32",6"

Rotolinear systems offer linear actuators. These actuators are with ball screws or lead screws depending on the application and normally with 12v dc /24v dc motor + 110/230vac converter + remote hand set. It is used for furniture, satellite, automation, dish antenna, fitness equipment, furniture’s, hospital equipment ect. The standard stroke available is upto 612mm and the max dynamic load carrying capacity is 800 to 8000n and static around 13600n. The speed of ball screw driven linear actuator will 4.5- 65mm/ sec. The protection will be ip65; ip54 depending on the models and preset limit switches is included. The optional accessories like potentiometer, hall effect sensors

• Material: Metal
• Feature: Rust Proof
• Jack Type: MWJ 15
• Static Load: 75000 N
• Stroke: 1524 mm
• Thickness: 5-10mm

We have parted our infrastructure into different units and one of them is warehouse wherein we keep our product lot for meeting urgent and bulk requirements of the buyers at a time. Located in Bangalore(India), we have made our distinguished position in the market since our products are qualitative and of utmost standards.

We offer motorized linear slide.

• Peak Load: 2200 kgf
• Stall Load: 3000 kgf
• Rated Load: 1100 kgf at rated voltage
• Rated Voltage: 80 ± 5 VDC
• Speed At Rated Load: 165 mm/second
• Stroke: ± 30 mm
• Size: 102 x 106 x 270 mm excluding controller
• Weight: 6.45 kg
• Total Time of Operation: 500 second
• Feedback Sensors: Tacho and LVDT

• Brand Name: Festo
• Type: Linear drive with displacement encoder
• Stroke Length: 40 - 990 mm
• Diameter: 160 mm
• Force: 4712 - 48255 N
• Features: Integrated displacement encoder,  A choice of integrated positioner and valve block,  Piston rod with male thread

• Brand Name: Oriental Motor
• Frame Size: 130mm
• Features: High Efficiency and Energy Saving, High Power, High Rigidity, High Positioning Accuracy with Non-Backlash
• Permissible Moment Load: 50N m
• Frequancy: 50/60Hz
•  Current: 3.6A
• Permissible Speed: 200r/min
• Mass Control Circuit: 0.75kg
• Runout of Output Table Inner Diameter: 0.015mm

We design and manufacture a wide range of custom built Rotary Actuators.

• Material: Aluminum, Brass, Carbon Steel, Stainless Steel
• Application: Gas Valve, HVAC System, Liquid Valve
• Color: Blue, Green, Red, White, Yellow
• Voltage: 110V, 220V, 380V, 440V
• Power: Electronic, Hydraulic, Pneumatic, Solenoid
• Pressure: High Pressure, Low Pressure, Medium Pressure, Vacuum

• Actuator Operation Type: Electrical Operations
• Product size: 1/4 ” to 12 ” Available BSP , BSPT , NPT, etc.
• END Connection: Screwed End / Flanged End other types also Available on Request
• Maximum Working Pressure: Vacuum to 1500 bar, other Pressure are Available on request
• Circulation Media: Fluids, Air , Petroleum Products , Chemicals ETC,
• Rated Voltage: 12 , 24, 110, 230, AC/DC 9-35V, AC110-230V, 50 / 60 Hz Available
• Wiring control methods: CR2-01, CR2-02 , CR5-01, CR5-02, CR7-04,
• Working current: ≤ 500MA , ≤ 800MA
• Open/Close Time: ≤ 1 to ≤ 143 Sec
• Life Time: 70000 times to 1Lakh times & More
• Valve Body Material: Nickel Plated Brass, Stainless steel 304 & 316 (Optional Available )
• Actuator Material: Engineering Plastics , Alluminium Die Cast,
• Sealing Material: EPDM & PTFE , Viton (Optional Available)
• Actuator Rotation: 90° , 180° degree ,
• Max. Torque Force: 2 to 35000 Nm
• Cable Length: 0.5m,1.5m （Optional）
• Environment Temperature: -15℃ ～ 50℃
• Liquid Temperature: -196 ℃ ～250 ℃ other Temperature are Available on Request
• Manual Override: □ NO □ YES （Optional)
• Indicator: YES
• Protection Class: IP67 / Explosion Proofs

These heavy duty force generators apply equal axial forces in tension and compression with excellent dynamic characteristics. The design incorporates low friction, wear resistant seals for smooth and leak free operations. BISS actuators incorporate a monolithic piston design with inbuilt digital encoder of 0.1 µ resolution to track displacements, these features make our actuators more reliable with precise control to meet most of the demanding applications of testing. Double ended double acting monolithic piston design to apply equal axial forces in tension and compression, Coaxially mounted encoders with 0.1 micron resolution for precise control of displacements.

• Voltage: 12 / 24 V D C
• Force Range: 5 N - 120 N
• Stroke: 2mm 35 mm

Solenoids basically are electrical devices used to convert electrical energy into linear mechanical motion. The energy produces within a solenoid can either be used to provide a straight linear pulling action, or it may be converted to provide rotary action. In either case the magnetic pull force increases as the air gap is reduced between armature and core. 

Linear actuator is an electrically operated device which help push or pull objects. These actuators can handle a lifting capacity of 200 – 12,000 Newton. They are quiet, safe and has a clean and accurate motion control. Linear actuators are widely used for applications like hospital bed, dental chair, ICU beds, OT tables and so on. Because these actuators are easy to install and required no maintenance most hospital bed and furniture manufactures prefer these actuators.

• Type: Linear Actuators
• Material: Aluminum, Steel
• Certification: ISO 9001:2008
• Color: Black, Blue, Red, Shiny-silver, Silver
• Pressure: High Pressure, Low Pressure, Medium Pressure
• Feature: High Strength, Reliable Functioning, Sturdiness
• Phase: Double Phase, Single Phase, Triple Phase
• Construction: Permanent Magnet
• Retracted length: 0-20Inch, 20-40Inch
• Surface Finish: Color Coated, Silver Coated
• Valve Motion: Electric Actuator, Linear Motion Valve

• Pressure: High Pressure
• Retracted length: 26"
• Rated Load: 1200 lb
• Stroke Length: 36"
• Speed At Rated Load: 9 in/min
• Voltage: 24 V DC

• Bore: up to 250 mm
• Stroke: up to 5000 mm

Cylinders as per ISO 6020-2 and ISO 6022 Pressure up to 320 bar ATEX version available Stainless Steel cylinders

Electrical Actuators are used for the automation of industrial valves and can be found in all kinds of technical process plants: they are used in wastewater treatment plants, power plants and even refineries.

servo actuators, Test Rigs, simulators, dc servo controllers