Conformal Coatings Dealers (69 products available)

• Type: Conformal Coating, Industrial Automation
• Form: Liquid
• Brand Name: ASS
• Application: Industrial Use
• Pack Size: 400 ml, 500 ml

Features of ACC 2010 Acrylic Conformal Coating ACC 2010 Acrylic Conformal Coating is a flexible transparent acrylic coating for the protection of electronic circuitry formulated to meet the highest resistance requirements. Used on printed circuit boards as protective coating against moisture, dust, humidity and fungus. Protects all Electrics/Electronics Circuitry equipments in Extreme Service Environments. Excellent adhesion and dielectric properties. Good moisture resistance & Quick Evapouration.   Application of ACC 2010 Acrylic Conformal Coating It used as extra/after insulation of coils and transformers and reduces operational noise. Military Equipment Aerospace Industry Air Conditioner Circuit Board Industrial Applications Automotive Applications   Direction of ACC 2010 Acrylic Conformal Coating Shake well can before use at least 1 Minutes.Hold the can at least 15 to 20 cm from the surface you are spraying and keep the can upright during use. Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using. completed cure takes place in about 24 hours depends upon the humidity. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of ACC 2010 Acrylic Conformal Coating Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable aerosol. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized ontainer: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of ACC 2010 Acrylic Conformal Coating Storage : Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

• Packaging Size: 400 ml & 35 lit.
• Brand Name: ISC
• Features: Fast drying & crystal clear coat. , Easy to rework & repair. , Acrylic Base, Protection from moisture, corrosion, dust & temperature.
• Usage/Application: Industrial
• Physical State: Liquid

CONCOAT is a silicone based coating designed for the protection of printed circuit board assemblies & other electronic and electrical components from harsh environmental conditions. Its high dielectric strngth prevents short circuiting high voltage arcing and corona effect. CONCOAT is an air drying; room temperature curing, single component coating which protects the coated surface from moisture, dust, corrosion, fungus and thermal shock. Its fast air drying property allows components to be ready for further handling within 15-20 minutes, it convenient for further processes. It protects and insulates electrical and electronic components and assemblies including control panels, solenoid coils, generators, motors and transformers. Its good adhesion property allows it to be applied on a variety of substrates like metals, ceramics, plastics etc. CONCOAT does not contain any CFC's and is RoHS Compliant.DIRECTIONS FOR USE : Surface to be coated should be thoroughly cleaned prior to coating in order to ensure that satisfactory adhesion to the substrate is achieved. It should be free of moisture, flux residues, dirt, wax, grease, oil and other contminants. Contamination under the coating may become corrosive and lead to asembly failure. CONCOAT can be applied by spraying, brushing or dip coating, The liquid is in ready to use condition. However, over a period of extended time, viscosity change can occur due to solvent evaporation, In such a case, the viscosity can be adjusted by addition of Thinner/ Stripper. The thickness and uniformity of the coating depends on the operator's technique and must be determined by trials with the method concerned. CURING PROCESS : The coating will air dry tack free in 15 to 20 minutes, curing fully in 24 hours. The curing time can be accelerated by curing at room temperature for 2 hours followed by curing in an air circulating oven @80 degree C for 1 hour. This process will also ensure that maximum coating properties are achieved.

    Properties:          • Adheres well and forms a even filling Fast drying          • Protects PCB's from dust, dirt and other foreign particles          • Excellent electric insulating property   Applications:          • Specially formulated to protect PCB assemblies

• Packaging Type: Paper Box
• Coating Thickness: 0.5-1mm, 25-75 micron
• Speciality: Chemical Resistant, Water Resistant, Solvent Resistant
• Packaging Size: 1, 5 or 20L
• Usage: Industrial Use
• Brand Name: Humiseal
• Material: Acrylic,PU and Silicon
• Certification: UL,MIL,IPC,GX
• Shelf Life: 2Year
• Color: Clear
• Purity: 100
• Grade Standard: Industrial Grade
• Texture: Soft
• Form: Liquid
• Surface Finishing: Polished
• Country of Origin: India
• Waterproof: Water resistant
• Soluable In Water: No
• Weight Per Litre: 1 kg
• Density: 0.895
• Softening Point: 125
• Melting Point: 200
• Compressive Strength: nil
• Drying Time: 15 min
• Moisture: nil
• Specific Gravity: 0.895
• Viscosity: 200-350 cps
• Acid Value: nil
• Melting Temperature: nil

• Transparent: soldarable
• hard: ecofriendly

We are offering conformal coating. "global quality through indigenous technology" coninspune make acrylcoat conformal coating transparent ,sold arable , hard coating to protect printed circuit board assly .from environmental conditions like high humidity , conductive dust , corrosion , rust, fungus etc. The coating is ecofriendly with rohs , c-dot , soltspray , certificationand confirming to mil - 46058c specifications . available in 500 ml spray & 1 ltr lacquer . Normally ex-stock.

• Packaging Type: 100 sets
• Color: Blue
• Material: Silicone
• Thickness: 3.5-4mm
• Application: Electric Board Use
• Usage/Application: Masking cap for conformal coatings in PCB boards

Here are three simple reasons why you can save up to 80% of your costs when using reusable masking boots compared to other conformal coating masking methods: Masking time is reduced because using boots can be 4-5 times quicker than masking tape. De-masking time is reduced since it is much quicker to remove boots Masking boots don’t leak. Therefore, there is less repair due to masking mistakes. This means you can save a lot of money very quickly when switching to masking boots.Powerful 19.2V High Torque Motor • 6,000 PSI (413 BAR) Output Grease Pressure • Grease Output upto 3 oz. (85 gms) / minute in free flow • Automatic Air Bleeder & Bulk Loader • Automatic Pressure Release Valve • 30” High Pressure Hose with Spring Guard on both ends (prevents hose from kinking) • High Pressure Grease Coupler • Standard 1.5Ah Ni-Cd Battery Pack • An additional 1.5Ah Ni-Cd Battery Pack for un-interrupted greasing • One Hour Quick Charger (each battery charge provides power to dispense upto 6 Grease cartridges in free flow condition) • Comes with Blow Moulded Case for conveniently storing when not in use

• Shelf Life: 24 Months from Date of Manufacture in Sealed Condition.
• Packaging: 400 Ml Aerosol Spray - 550 Ml Aerosol Spray

High Gloss Fast Drying Flexible Acrylic Conformal CoatingELECTOCOAT is a fast air-drying, lightweight, clear, tough and flexible acrylic coating designed primarily to protect printed circuit boards and electrical / electronic equipment against high voltage arcing, corona shorts, corrosion, ingress of moisture and fungus. It resists rust, tarnish, corrosion, moisture and has excellent waterproofing / weatherproofing abilities. ELECTOCOAT is highly abrasion & scratch resistant and protects electronic equipment completely due to its high dielectric strength. It does not contain any harmful chlorinated solvents, CFCs or ozone depleting chemicals.Benefits Protects against rust, corrosion, tarnish, oxidation, moisture and weathering influences Provides a high-gloss, clear protective finish that remains transparent and does not fade or become yellow Provides a protective and insulating film that shields printed circuit boards from electrical leakage and short circuits Prevents sparking and corona discharges Non-conductive and has good dielectric properties Excellent resistance to weak acids & alkalis, water, oils and chemical fumes Easily solderable and very convenient for onsite repair jobs Conforms to requirements of specifications MIL-I-46058C Applications Insulation and protection of all electrical, electronic and high- tech equipment of: general electronics, printed circuit boards, thick film circuits, high voltage transformers, electrical motor coils, cables, wires; for moisture proofing and corrosion prevention of any industrial, automotive, aviation, marine and military electrical & electronic hardware.Directions For Use - Bulk Mask and protect areas not to be coated. Apply steady even strokes by means of brush. Component to be coated can also be dipped into the coating. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity.Directions For Use - Aerosol Shake can vigorously for at least one minute after bearing noise from inside the can is audible. Mask and protect areas not to be coated. Hold can 12-15 inches away from surface to be coated and spray in steady, even strokes. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity. Clean the valve by inverting the can and spraying a few short bursts till only the clear propellant comes out. Clean the actuator button orifice by means of a thin, fine wire.Caution:- Contains flammable propellant and solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

We offer conformal coating,plastic coat. Conformal coating, plastic coat #4482 single component acrylic plastic coating, water clear transparency excellent electrical properties high resistance to burning,heat,cold,salt,alkalies.mild acid, will not crack peel-color does not contain any cfc’s or odc’s for industrial use only formulated with high performance acrylic resins,premium grade materials& engineered to offer excellent applications properties.this products provides superior gloss,excellent flow & leveling. Applications: enchances the lifespan of electronic pcb assemblies,seals dials,gauges,instruments,electric control panels,junction boxes. Improves their reliability & protect them from rust & corrosion. Directions for use: clean surface, shake well& build up coating by spraying 3 to 4 thin layer at an interval of 10 to 15 minutes of each coat

The Acrylic Protective Lacquer (APL) provides acrylic conformal coating to protect electronic circuits against rough environment that may contain moisture andor other chemicals. The transparent coating is generally 25-75µm thick and dries quickly after application.It allows electronic circuitry to withstand higher power and temperatures and also, permits miniaturization of circuitry while maintaining reliability.It may be soldered through, allowing easy repairing in a specific area on board without damaging the adjacent circuitry. The cured coating can be easily removed with solvents such as Ultrasolve (ULS).

We are offering pcb conformal coating

• Brand Name: MG Chemicals
• Packaging Size: 55Ml
• Packaging Type: Bottle
• Type: Silicone coatings
• Grade: Commercial Grade
• Application: Industrial

• Adhesion to: Aluminum, Ceramic, FR4, Metal, Plastic
• Temperature Stable: High, Low
• Dielectric Strength: 425 volts per mil v/mil
• Cure Characteristics: Fast Room Temp Tack-Free Time < 10 min
• Nonvolatile Content: 99.4 %
•  :  

• Packaging Size: 300 ml
• Packaging Type: Spray
• Grade Standard: Reagent Grade
• Color: White
• Country of Origin: Made in India
• Usage/Application: Industrial
• Physical State: Liquid

conformal coating to protect electronic circuits against rough environment that may contain moisture andor other chemicals. The transparent coating is generally 25-75µm thick and dries quickly after application.

• Applications: Printed Circuit Board, Electronic components etc.
• Pack Size: 300 gm (400 ml) Aerosol Can

It provides clear, colourless and wear resistant coating to electronic circuitry. Quick drying and scratch resistant protects circuitry from dust and moisture. Also used as an anti-corrosion coating for PCB’s and other components. If needed allows re-soldering.

• Brand: Automotive Solutions
• Physical State: Liquid
• Packaging Type: Bottle
• Usage: Personal
• Packaging Size: 300 ML
• Color: Clear
• Features : High Moisture & Chemical Resistant, Fast Drying, Transparent 

We offer Conformal Coating. Conformal coating :conformal coating material is applied to electronic circuitry to act as protection against corrosion ,moisture, dust, chemicals, and temperature extremes that if uncoated (non-protected) could result in a complete failure of the electronic system.

Our Acrylcoat Conformal Coating is well accepted in the Electronics industries. The product enjoys excellent reputation for its quality. CONINS PUNE has a state of the art manufacturing plant and a well-equipped R&D facility for developing and testing its products with totally indigenous technology. This is backed by highly qualified and well experienced Engineers. Consistency in quality CONINS PUNE ‘hallmark.

• Packaging Type: Can
• Packaging Size: 360 ML aerosole Can,1 Litre,5 Litre,20 Litre
• Density: 0.92 g/cm3
• Usage/Application: Industrial
• Recommended Coating Thickness: 25 to 75 microns
• Shelf Life at Room Temperature: 24 months

• Type: Conformal Coating

• Country of Origin: Made in India
• Brand: DC
• Usage/Application: Industrial

Choosing the right conformal coating and application process isn't easy, and there is no such thing as a 'perfect' conformal coating product. Time and effort invested in getting it right can be amply rewarded by the near elimination of end product failures in the field. These failures andor recalls can be the most expensive, reputation damaging and dangerous problems a company will ever experience. In short, if you have to conformally coat your boards, you have to get it right. But when you do: you protect your customers and your profits. Chase Electronic Coatings manufactures of HumiSeal conformal coatings, provide advanced products for different applications needed.

• Usage/Application: Industrial
• Physical State: Liquid
• Packaging Size: 500 ml
• Brand: Spraysol
• Packaging Type: Aerosol Can
• Grade Standard: Reagent Grade
• Country of Origin: Made in India

eazycoat Multi-Axis Coating System provides a reliable robotic conformal coating application platform for low and medium volume batch and inline conformal coating processing.Equipped with programmable software and stepper motor process control, the straight forward design means ease of application of conformal coating at all levels.

• Features: Purity , Effectiveness , Correct composition .
• Application: Used for coating of PCB
• Packaging Size: 400 ml / 500 ml
• Brand Name: Miracle
• Grade: Analytical Grade
• Physical State: Liquid
• Application: Industrial
• Country of Origin: Made in India

• Acrylic: Moisture proof
• Polyurethane: Moisture and Chemical prroof
• UV Curable: Very fast curing
• Silicon: High temperature operation
• Synthetic Rubber: High humidity applications

Drive technologies is the ony official distributor,stockist and technical support company for humiseal products in india. the products include world class conformal coatings,masking tapes and dots,uv inspection torches,thinners,strippers.