Programmable Counter Dealers (35 products available)

Accepts Proxy Encoder  Totalizing Mts/Min Indicator, Rate encounter, RPM measurement. 100% Accuracy  4 + 4 digit display  2-set points,2-Relay outputs 90-260 VAC, 50 Hz  72H X 72W DIN size and 96H X 96W DIN size.

• Type: Programmable Counter
• Application: Industrial
• Color: Grey
• Voltage: 220V
• Display Type: Digital
• Automation Grade: Automatic
• Series: CT Series
• Brand Name: Autonics

New CT series adopts RS 485 communication function so that each parameter setting and monitoring can be available from PC. In addition, it allows up to 6 digit prescale setting possible to provide user convenience. Increased contact capacity of load to 5A and new design nameplate are another features of NEW CT series.

• Input : PNP / NPN Proximity sensor, Potential free contact, Encoder
• Display : individual display for counts & set-point 4 / 6 digit LED Display
• Power Supply : 230 / 110 VAC , 24 VDC
• Accuracy : Better than ±0.01 % of FS for encoder i/p
• Alarms : maximum 3 Nos.
• Interface : RS 485 / MODBUS RTU / ASCII ( optional)
• Mounting : Panel

• Micro controller Based & Fully programmable Programmable Event Counters• Auto Reset for setpoint• Low & High Speed Selection• Realy hold time programmable• Password protected programmable scale factor  

• Input: Proximity switch, Photo sensor, Limit switch, Encoder, 230 VAC pulse
• Range: 0-999999 Total counts, Total meters
• Reset: Front Panel key / back terminal for remote reset / Auto Reset
• Set point: Single/Dual set point
• output: 1CO, 5Amp, 230 V AC Relay / Buzzer Output

• Input : Proximity switch, Photo sensor, Limit switch, Encoder, 230 VAC pulse • Range : 0-999999 Total counts, Total meters • 0-9999 Batch count, Meters/min, RPM, Rate • Reset : Front Panel key / back terminal for remote reset / Auto Reset • Set point : Single/Dual set point • Output : 1CO, 5Amp, 230 V AC Relay / Buzzer Output • Setting : By front key pad, Thumbwheel for preset counter • Size : 48 x 96, 72 x 72, 96 x 96 (mm) • Power : 230 VAC, 50 Hz . • Up / Down Counting selectable. • Non-Volatile memory

• grey: red
• grey: red

It is a micro controller based counter which accepts input as pulse input / event generation / object counting used in the measurement objects and events or engineering units like length measurement in 4 / 6 / 8 digit version. This unit has the facility to count and control the event generation or object detection involved in various operations in industrial atmosphere. The operation mode has the facility to count in both up or down counting selected thorough programming. The front panel programmable set value generates the necessary control output at the rear side. It has the data storage facility for storing the set values. The rs 232c communication output also available on request. (eg. Length measurement, batch counting, object counting etc.,).

• Display Type: Digital
• Brand: DPM Instruments
• Features: High Functionality,Energy Efficiency,Master-Slave based clock
• Display Digit: 4 Digit
• Panel Cutout Size: 90 x 90 mm
• Dimensions: 96 x 96 x 110 mm
• Modal: CL-1000

• DIMENSIONS: 96X96X140mm

Programmable counter COUNT MODE: Up/Down selectable 10 different type (Programmable), BACKUP POWER FOR MEMORY: 100 Years,POWER SUPPLY: 180 - 230V AC ± 10% 60/50Hz.

Programmable On Time & off time anywhere in the ranger of 23hrs:59mins:59secs 5 feedback monitoring of Errors from 3limit switches & level & pressure occurrence of error & retrieval of errors against real time are logged in the memory for later retrieval and analysis Retreval of the data collected is essential for the maintenance dept to monitor & correct the errors for normal operation else which leads to downtime of the vehicle or machinery

Owing to our rich experience and knowledge of this domain, we have been able to offer Programmable Counter to our valuable customers. These programmable counters are used to perform up-down counter or length counter with Rate Indication in various industrial applications. Used in various plastic and textile industries, these counters are manufactured as per the industry set norms.

Totalisers XC 22B :: 4 Digit, Preset Counter XC 41010B200NX :: 6 Digit, Multifunction, Quadrature input 2 Set Point scalable input RC 102A :: Rate Indicator & Totaliser (scalable input) RC 2106 :: Rate Indicator (scalable input) RC 2108 :: Rate Switch (scalable input)

• Range: -0.01 sec. to 99.99 sec

New CT series adopts RS 485 communication function so that each parameter setting and monitoring can be available from PC. In addition, it allows up to 6 digit prescale setting possible to provide user convenience. Increased contact capacity of load to 5A and new design nameplate are another features of NEW CT series. ( ※ NOTE that existing CT series will be discontinued. )

• Model Name/Number: MPC-1065
• Brand: Multispan
• Dimensions: 96 (H) x 96 (W) x 52 (D) mm
• Display Digit: 128 x 64 Bit Graphical LCD
• Voltage: 230 V AC
• Panel Cutout: 92 (H) x 92 (W) mm
• Relay Type: NO-C
• Power consumption: 6 VA
• Keys: SET, CURSOR UP/DOWN, INC, DEC, ENT/RST
• Operating Temp.: 0 DegreeC to 55 DegreeC
• Relative Humidity: UP to 95% RH (non-condensing)
• Protection Level (AS Per Request): IP-65 (Front side) As per IS/IEC 60529 : 2001

• Memory: Count retains in Memory without power, without battery.
• Display: 6 Digit, 0.56. LED display
• Input(PNP): Proximity Switch(PNP), Photo Sensor, Voltage Pulse (max 30V)
• Supply voltage: 230V AC +-10% 50Hz
• Scale Factor: 0.00001 to 999999(user programmable)
• Panel cut-out: 46 x 92 mm.
• Weight: 400 grams approximately.
• Power Consumption: 5 Watts
• Dimension: 48mm x 96mm x 130mm

• Display: 6 Digit, 7 segment LED display (0.3” height)
• Input Frequency: a. 0 to 30 Hz b. 0 to 1 KHz
• Sensor Supply: 10V DC, short circuit protected

6 Digit Preset Counter Dual Limits settable with dual relay output Programmable Scale Factor of 0.001 to 999.999 Pre-settable Batch Counter Cumulative 6 Digit Counter UpDown Counting Selectable NormalAuto-Reset with Time setting Non-Volatile memory to hold settings and counts Program configuration lock at rear External Setting for SlowFast for noiseless operation

•  Range:  User Selectable Range.
•   Input:  NPN / PNP Proximity / Micro Switch  230v Ac Pulse.
•   Memory:  Non-volatile Memory When Power Fail.
•   Reset:  Auto / manual Reset.
•   Supply:  230v Ac, ±20%, 50Hz, .
•   Size (H x W):  92 x 92, 68 x 68. (mm)

The Selec XC200NX is a 6 digit Counter with push wheel setting suitable for counting operation of equipment, machinery, systems or processes in a wide range of industrial applications. It has following operating modes on-delay, Interval delay, auto reset, time pulse repeat. Accepts input from - Proximity switches, Encoders, Potential free contacts with optional 10 years memory retention, with input speed from 0 to 5 KHZ and 9999 counts and 4.00 RPM/RPH to 99999 RPM/RPH and to operate two independent relay output contacts with two set point which are isolated from the supply voltage. These counters are housed in a compact panel mounting enclosure and are powered from 85 to 270V AC/DC.   Features 5 digits RPM indicator, 6 digts counter LED status indicator: Relay 1, Relay 2 2 setpoints Programmable input scaling Up, Down, Quadrature & Bi-directional

PRiCO (Programmble intelligent Counter) PRiCO provides a very cost - effective and reliable solution to many complex counting requirement. What sets PRiCO apart from the convention facet. SPECIFICATIONS : Counting modes » Up counting » Down counting » Quadrature counting » Bi-directional counting Display 7-digit, seven segment LED display (10mm height) » Counter/Totaliser/Batch: 7- digit display » Rate : 5- digit display » RPM : 6- digit display Range » Counter/Totaliser:Selectable least count 0.000001, 0.00001, 0.0001, 0.001, 0.01, 0.1, 1 » Rate: Rate per minute (RM) / Rate per hour (RH) user selectable. (minimum frequency for Rate mode is 10 Pulses/minute) » RPM: 10 RPM to 360000 RPM Set points » 3 user programmable set points. » SET1 , SET2 :Dedicated for COUNTER mode. » SET3 : User programmable for any one of COUNTER / TOTALISER /BATCH / RPM. Relay operating mode » Relay ON mode » Relay OFF mode » Pulse time mode     a) Time pulse repeat mode     b) Auto-reset mode Count inputs » Voltage pulse : 8 to 30 V DC amplitude from proximity switch, encoder. » Potential free contacts from limit switch, micro switch. Input frequency » 0 to 6 KHZ: In up / down mode » 0 to 3 KHZ: In quadrature mode / bi-directional mode. Sensor supply » 12 V DC, 60mA (+/- 10 %) Scale factor » Programmable » scale factor = X x 10Y     X = From 0.000001 to 9.999999     Y = 0, 1, 2, -1, -2, -3, -4, -5 Reset input » Manual / Front panel reset: with enable / disable facility » Remote/ Back panel / Electrical reset: User selectable     ( minimum time for remote reset is 10 ms. ) » Reset through programming mode: User selectable Relay outputs » Three Relays ( one relay for each set point ) » Relay1/ Relay2 for set1/set2 operation ( COUNTER ) » Relay3 for set3 ( COUNTER / TOTALISER / BATCH / RPM ) – Programmable » Relay ratings: Rated for 5 Amp at 230 V AC Memory retention » Upto 10 years Protection » Parameters     a) Password protected     b) Hardware protected (Dip switch setting) » Set points     a) Software protected (Through program configuration i.e. ‘SdF 3.’) Supply » 230 V AC (+/- 10%) Mounting » Panel mounting Weight » approximately 580 gms Operating temperature » 0° to 50° C Relative humidity » 10 - 95% non-condensing Overall dimensions » (All dimensions are in mm.)

Programmable counter Programmable Temperature Scanners with PrinterComputer Interface, Single Isolators Convertors Current Transducers, Programmable Counters : Length Counters, Batch Counter, Presetable Counters. Profile Temperature Controller.