Suguna Motors & Pumps Avinashi Road, Coimbatore, Mahaveer Market

Transfer a wide range of nonabrasive or nonparticulate viscous liquids with a continuous, near-pulseless flow in many industrial, commercial, marine, or agricultural applications. All have keyed shafts, a seal flush chamber. Cast-iron and bronze models have pressure relief valves. Ball bearings allow use with pulley-drive systems. Note: Higher-viscosity liquids (100,000 SSU) must be transferred with more horsepower at reduced speeds.

The borewell compressor pump works on the principle of difference in density of two-inter-connected water columns and the heavier one over balancing the lighter one. Water outflow through delivery pipe will be pulsated. the discharge of water will greatly depend on the yield of the bore. Air distributor fitted at the end makes this operation possible.

Suguna Car Washer is a single plunger,oil splash lubricated reciprocating plunger type water pump.It consists of a plunger and plunger housing fitted to the crank case. The suction pipe with filter, balancing drum, safety valve, and the delivery hose are fitted to the plunger housing. the delivery hose is fitted to the plunger housing through a connector which also accommodates a pressure gauge and a manometer safety device.At one end of the crank shaft is fitted dynamically balanced fly wheel cum pulley.’V’ The motion fitted on a basetank with provisions for belt tension adjustments.

Suguna Submersible motor is a squirrel cage water cooled and water lubricated induction motor. The pumps are of radial mixed flow type pumps. The bearings are water lubricated.Submersible pumps are for purifying water from deep wells using submerging in water. 4″ borewell pumps are used for drawing water from 62-1500ft and can be used for irrigation, sprinkler, residential and for multi storied buildings

Compact and light weight , Adjustable outlet pressure for different applications, Corrosion – Resistant stainless steel valves, All working parts, connecting rod, crankshaft and bearing are lubricated by oil bath. Automobile workshops, Service Stations, Industrial Boiler Feed.

Motor & Pump Casing are made out of high grade cast iron material, S.S. Shaft and cast iron impellers, Two water Lubricated carbon bearings used for longer life, and smooth operation, 2880 RPM – 415V, 50 Hz 3 phase supply water cooled motor.

Submersible pumpset cable selection chart for 415V – Three Phase – 50 Hz. APPLICATIONS:4″ Submersible pump, 6″ Submersible pump. 1. HP 7.5D and above are STARDELTA motors. 2. For STAR DELTA Starting reduce current by 13 for selecting suitable cable Example : For a 20 HP motor at 350 volts and 90 metres actual cable length. Calculated length = (415+350) x 90 = 107m. The size of the 2 cable to be selected for 107m from the chart is 6mm

Transfer a wide range of nonabrasive or nonparticulate viscous liquids with a continuous, near-pulseless flow in many industrial, commercial, marine, or agricultural applications. All have keyed shafts, a seal flush chamber. Cast-iron and bronze models have pressure relief valves. Ball bearings allow use with pulley-drive systems. Note: Higher-viscosity liquids (100,000 SSU) must be transferred with more horsepower at reduced speeds. Steel spur gears handle oil-based fluids. Viton® mechanical seals with carbon-on-ceramic faces provide good resistance to compatible chemicals. Other wetted materials are: cast-iron, steel, and Hilite-55.

CENTRIFUGAL MONOBLOC PUMPS (SINGLE PHASE TWO & THREE PHASE*) APPROXIMATE PERFORMANCE AT 2880 RPM, 240 VOLTS, SINGLE PHASE, 50 HZ OPERATION. Slow Speed High Speed Pumps. High Grade Cast Iron Body, Cast Iron Impellers.

APPROXIMATE PERFORMANCE DATA AT 2880 RPM 200 V, 50 HZ. MODEL:SWCM, TOTAL HEAD IN METERS:DISCHARGE IN LPM , SUCTION LIFT M (Ft) :9 (29). Products are manufactured in India, with facilities in Coimbatore and foundries in three locations. An advanced R&D facility in Coimbatore keeps Suguna Pumps on the leading edge of pump-related technology

Suguna Car Washer is a single plunger,oil splash lubricated reciprocating plunger type water pump.It consists of a plunger and plunger housing fitted to the crank case. The suction pipe with filter, balancing drum, safety valve, and the delivery hose are fitted to the plunger housing. the delivery hose is fitted to the plunger housing through a connector which also accommodates a pressure gauge and a manometer safety device.At one end of the crank shaft is fitted dynamically balanced fly wheel cum pulley.’V’ The motion fitted on a basetank with provisions for belt tension adjustments.

Plunger : The easy movement of plunger inside the brass sleeves, ensures positive suction and delivery. Valves : The brass valves provide smooth and direct passage for water from suction to discharge points. The spring fitted rubber valves help to reduce slippage and also ensures noiseless and smooth operation. Piston shaft : The stainless steel shaft connects the plunger assembly with the crank shaft of the pump and provides smooth running with minimum noise.

Piston : Automotive type low expansion aluminium alloy . Cylinder : Special cost iron, deep ” finned for quick heat dissipation . Valve Plates : Special Stainless steel material for high resistance and efficiency and for self floating . Inter After – Cooler : Deep finned aluminium alloy specially designed to keep temperatures low and minimize formation of carbon . Crank Shaft : Made of Carbon steel dynamically balanced with roller bearings . Diaphragm Pressure Switch : For efficient automatic On and Off automatic venting and no’load restarting of compressor units, pressure switch pressure switch with electromagnetic unloader is provided.

Ideal for handling oil-based liquids.Wet-end components are cast-iron,steel, Hilite-55(Cellulose), and Viton. Nos. Sug91 to Sug96 have wet-end components of steel, cast-iron, Hilite-55(cellulose) and Teflon. Steel spur gears. Zerk model use Teflon and nonZerk model use Viton lip seal.

Compact and light weight , Adjustable outlet pressure for different applications, Corrosion – Resistant stainless steel valves, All working parts, connecting rod, crankshaft and bearing are lubricated by oil bath. Service Stations, Industrial Boiler Feed, Food processing industries.

CENTRIFUGAL MONOBLOC PUMPS (SINGLE PHASE TWO & THREE PHASE*) APPROXIMATE PERFORMANCE AT 2880 RPM, 240 VOLTS, SINGLE PHASE, 50 HZ OPERATION APPLICATIONS: Domestic Agricultural use Industrycentri ,mono bloc Fire Fighting, Water Circulation,

The borewell compressor pump works on the principle of difference in density of two-inter-connected water columns and the heavier one over balancing the lighter one. Water outflow through delivery pipe will be pulsated. the discharge of water will greatly depend on the yield of the bore. Air distributor fitted at the end makes this operation possible.

CENTRIFUGAL MONOBLOC PUMPS (SINGLE PHASE TWO & THREE PHASE*) APPROXIMATE PERFORMANCE AT 2880 RPM, 240 VOLTS, SINGLE PHASE, 50 HZ OPERATION. Slow Speed High Speed Pumps, High Grade Cast Iron Body, Cast Iron Impellers, Single Phase Three phase.

The borewell compressor pump works on the principle of difference in density of two-inter-connected water columns and the heavier one over balancing the lighter one. Water outflow through delivery pipe will be pulsated. the discharge of water will greatly depend on the yield of the bore. Air distributor fitted at the end makes this operation possible.

Installed on wheels for easy portability, Handle any grade of grease, Built in air regulator to maintain constant ,pump working ratio, Pressure regulator valve assembly can be adjusted up to 4Kgf Cm2 pressure, Pressure plate Follower plate, Swivel assembly at both side of hose.

Suguna Jet Centrifugal pump combination are designed for high efficiency, operate on optimum total head with good discharge characteristics and low power consumption.The components are made of selective materials under strict quality control. Tolerance are of high standard ensuring reliability and durability.

Single phase, three phase electric motor of robust, heavy construction that are durable and working at various voltage conditions. Special motor for industrial applications and as prime mover for pumps, compressor and wet grinders etc. Shaft – EN 8 steel rotors – pressure die cast and dynamically balanced stator core pack – built from low loss electrical grade steel laminations. the stator winding consists of modified polyesterpolyesterimide base insulated copper wire to give high conductivity and impregnated with synthetic resin to attain high die electric properties Windings are tested on surge comparison tester Die cast aluminium body for frames 56 to 100

Suguna Submersible motor is a squirrel cage water cooled and water lubricated induction motor. The pumps are of radial mixed flow type pumps. The bearings are water lubricated.Submersible pumps are for purifying water from deep wells using submerging in water. 4″ borewell pumps are used for drawing water from 62-1500ft and can be used for irrigation, sprinkler, residential and for multi storied buildings

An Arrow cast on the pump casing indicates the direction of rotation. The pump casing to be filled with water before initial starting. INI ever run the unit with gate valve closed. To avoid rust formation in the pump casing, RUN the unit for a few minutes daily.