SEFSO Shastri Nagar, Jalandhar, Punjab

  • grain refiner

    grain refiner

    Request for Price

    100 Piece(s) (MOQ)

    We are one of the leading Manufacturers, Exporters and Suppliers of reliable Grain Refiners in Jalandhar, Punjab (India). Made from premium aluminium, our Grain Refiners are robust and durable. We make them available in varied specifications to meet different requirements of customers. Interested buyers can get Grain Refiners from us in bulk and expect on time delivery of consignments. Sefrefiner is normally sold in capsules of 25 & 50 grams. It is a whitish Powder packed in Aluminum Sheet. Consumption : 200 grams of Sefrefiner is recommended per metric ton of melted brass to be inoculated. This equates to one 50 gram capsule for each 250 kilograms of melted brass. Alloy Requirements : Best casting results will occur with clean yellow brass ingot. Otherwise the basic Scrap Brass must be free of inclusions which are identified by a visual check of the polished surface. Good grain refinement usually occurs when the copper content is between 56 and 62 percent. Optimal grain refinement usually occurs when the copper content is 59.5 percent the aluminum content is 0.6 percent. Sefrefiner has been used to lower the casting temperatures and increase the castability and fluidity. Method Of Use :As a safety precaution, care should be taken to preheat the Sefrefiner capsules on the furnace rim, shelf, etc. so they are free of any moisture. Any adjustments to the Aluminum or Zinc content of the melt should be made prior to adding Sefrefiner. The surface of the melt should be reasonably free of slag. Sefrefiner should be added to the melt by immersing the capsules about 50 cm-75cm (approx 25 inches or 2 feet) below the liquid metal surface using a bell shaped plunger. Expected Benefits : Depending on the alloy composition, the use of Sefrefiner can result in the following casting benefits:  Improved fluidity of the metal to be cast. Lower casting temperatures are possible depending on the size of the part to be cast and the type of mold to be used. Cracking tendencies of the parts to be cast are greatly reduced and most often, cracks are eliminated. The occurrence of Sinks/Misruns/Cold Shuts are greatly reduced. Lead is more uniformly distributed in the fine grain structure of alloy. Monetary Savings : Using Sefrefiner can result in the following savings:   Cost of purchasing fine grained ingot gets reduced. Casting scrap is reduced. Finishing and rework costs are reduced. Energy is saved resulting from lower casting temperatures.

    ...more
    Get Best Price
  • Neutral Flux

    Neutral Flux

    Request for Price

    Our company is one of the eminent Manufacturers, Exporters and Suppliers of premium Neutral Flux in Jalandhar, Punjab (India). Formulated out of premium chemicals, the Neutral Flux we offer is used extensively for varied industrial applications. We make it under hygienic conditions and guarantee our Neutral Flux is free of contaminations. Interested buyers can get Neutral Flux from us as per requirement in chemical grade packaging. Details : To be used : In all types of copper & copper based alloys.   Packing 50 kgs plastic bag. Physical Form : Powder cum semi granular flux. Consumption : 1% to 2% of molten metal. Instructions for use : Around 1% to 2% of flux should be thoroughly mixed with the charge (scrap, skimmings, swarf etc) and then should be fed into the furnace. if needed more of flux can be added during melting also.   Benefits : Reduces melting losses, improves metal recovery of scrap, swarf & skimmings, removes non-metallic contaminants, neutral flux, highly protective, strong cleaning action, suitable for wide range of alloys, furnace walls remain cleaned. Highly recommended to be used in all copper based alloys’ castings.

    ...more
    Get Best Price
  • Heat Conductive Coatings

    Heat Conductive Coatings

    Request for Price

    We are one of the prominent Manufacturers, Exporters and Suppliers of Heat Conductive Coatings in Jalandhar, Punjab (India). Our company has years of experience and we have mastered the art of formulating highly effective Heat Conductive Coatings. We make them available in varied grades and price each of the products economically. Buyers can get Heat Conductive Coatings from us in bulk.   Details : Physical Form : To be used in   All types of die castings of copper & its alloys.     Packing : 25/60 kgs plastic bucket/can. Physical Form : Semi-colloidal paste. Consumption : As per requirement, for best results, consider dilution ratio as 1:10 (1 kgs per 10kgs of water used) Instructions for use : For best results, inside the storage tank of water, continuous air agitation is a must, else stir it well from time to time manually using a long rod. Benefits : Increased heat transfer, encourages rapid cooling, results in easy release from the die, encourages filling thin sections fully, enhances the surface finish.   highly recommended to be used in all copper based gravity die/low pressure die castings.

    ...more
    Get Best Price
  • Water Based Graphite Coating

    Water Based Graphite Coating

    Request for Price

    We are offering water based graphite coating to be used in metal casting industry, aluminium, brass, copper etc. Product name : sefcote dgl description : semi colloidal graphite based heat conductive coating specially designed for aluminium ingots, sow bars, brass die casting etc. To be used in : all types of die castings of copper & its alloys, all types of aluminium sow and t-ingot melting. Packing : 2560 kgs plastic bucketcan. Physical form : semi-colloidal paste. Consumption : as per requirement, for best results, consider dilution ratio as 1:10 (1 kgs per 10kgs of water used) instructions for use : for best results, inside the storage tank of water, continuous air agitation is a must, else stir it well from time to time manually using a long rod. Benefits : increased heat transfer, encourages rapid cooling, results in easy release from the die, encourages filling thin sections fully, enhances the surface finish.

    ...more
    Get Best Price
  • Biomass Briquettes

    Biomass Briquettes

    Request for Price

    150 Piece(s) (MOQ)

    We are ranked among responsive and responsible Manufacturers, Exporters and Suppliers of Biomass Briquettes in Jalandhar, Punjab (India). Made out of organic components, our Biomass Briquettes are eco-friendly and give out high energy. They are regarded as reliable alternative fuels. Buyers can get Biomass Briquettes from us in bulk anytime of the year. Usage : NOGAS briquettes are convenient to apply and most effective in removing dissolved hydrogen from molten copper and its alloys. A compacted degassing briquette is plunged beneath the metal surface to release a stream of scavenging gases from the decomposition which ensues. The scavenging gases do not produce any objectionable or toxic fumes and the only equipment required is a suitably protected plunger rod. NOGAS is supplied as strong, robust briquettes that can be safely and easily stored, handled and applied.Degassing with NOGAS briquettes can be carried out in the furnace in the case of lift-out, tilting and high frequency furnaces. For larger units it is recommended that degassing should be carried out in the transfer ladle.The NOGAS briquettes are so designed that they can be attached to or wedged on, to a variety of plunger rod shapes, etc. Perhaps the most suitable tool is a simple steel rod, furnished with a peg or stop to prevent the briquette riding up the rod, when plunged into molten metal.The briquette may also be wired to a suitable plunger made from either steel or graphite or, if a suitable graphite rod is available, the end can be turned down into a cone shape and the briquette wedged on to it. This is the most satisfactory method since it leaves the largest surface area of the briquette exposed to produce the scavenging gases. For very large melts a dummy stopper rod is probably the best approach. Advantages of using NOGAS : inexpensive requires no costly equipment easy to apply considerably improves mechanical properties effectively eliminates gas porosity due to hydrogen safe - non-toxic easy to store. Consumption : One piece to be plunged beneath the molten metal for 8 to 10 minutes for 250 to 300 Kgs of metal. In case of more than 300 Kgs, additional piece has to be fixed in plunger for every 250 Kgs of metal. Piece will not get dissolved but the chemicals inside it will get used in a single use only. (Plunger rod needs to be designed as per number of pieces to be used.)

    ...more
    Get Best Price
  • Liquid Graphite Lubricant

    Liquid Graphite Lubricant

    Request for Price

    100 Kilogram (MOQ)

    DESCRIPTION : SEFCOTE DGL (AS) IS A GRAPHITE BASED, NON-REFLECTIVE, HEAT CONDUCTING COATING SPECIALLY DESIGNED TO COAT ALUMINIUM T-INGOTS OR SOWS.   TO BE USED ON: SEFCOTE DGL AS IS APPLIED TO THE SURFACE OF ALUMINIUM PRIOIR TO MELTING, TYPICALLY IN A DRY HEARTH FURNACE. PACKING : 20 KILOGRAMS BUCKET (CUSTOMISED PACKING ALSO AVAILABLE) PHYSICAL FORM : SEMI-COLLOIDAL PASTE CONSUMPTION : AS PER REQUIREMENT.IT CAN BE FURTHER DILUTED USING DISTILLED WATER. INSTRUCTIONS FOR USE : STIR THE COATING WELL BEFORE USING. APPLY IT EITHER USING PAINT BRUSH OR SPRAY GUN OR AUTOMATED SPRAYER (ONLY AFTER DILUTING IT TO REQUIRED CONCENTERATION)    Application is best if applied to all sides of the material that are exposed to the furnace’s radiant heat. The coating is typically applied to the top and sides of a sow or Tbar.   BENEFITS : SEFCOTE DGL (AS) reduces the reflectivity of the aluminium, thereby increasing the absorption of radiant heat into the aluminium. Non-coated aluminium naturally reflects heat from its bright surface, taking longer TIME to melt than aluminium coated with SEFCOTE DGL (AS). Time is almost reduced to half as compared to non-coated Aluminium Melting in Hearth Furnace. Decreasing melt time has many advantages, including increased productivity and decreased energy usage. Highly recommended to be used on all types of Aluminum T-Bars, Ingots, Sows etc when made to be melt in hearth furnace.   Increase melt rate 20–100% Reduce production cost Reduce carbon footprint proportional to reduced energy use.

    ...more
    Get Best Price
  • DEOXIDATION TUBES (PHOSPHORUS BASED)

    DEOXIDATION TUBES (PHOSPHORUS BASED)

    Request for Price

    100 Piece(s) (MOQ)

    We are offering deoxidation tubes. Phosphorus based deoxidation tubes used to remove oxygen from copper based alloys product information manual d.o.tubes introduction- deoxidising agents for copper & copper based alloys. D.o.tubes are individual copper based tubes containing a variety of reagents. D.o.tubes are specially designed to remove dissolved oxygen formed during the melting process. If this dissolved gas is allowed to remain in the melt it can seriously reduce mechanical properties and pressure tightness of the casting. Thus, d.o.tubes are used to maintain the mechanical properties and reduce rejections due to defects. Usage upon completion of the melting process using the appropriate covering and cleaning agents, the melt should be deoxidised to remove dissolved oxygen. It is most important that the slag is completely removed (specially in the case of oxidising slags) before treatment with d.o.tubes in order to prevent a reaction between the deoxidising agent and oxygen contained in the slag. D.o.tubes should be plunged quickly down to the bottom of the melt using a forked plunging rod and kept there until the reaction is complete. consumption d.o.tubes comes in three sizes. D.o.tube i- for 25 kgs of molten metal d.o.tube ii- for 50 kgs of molten metal d.o.tube iv- for 100 kgs of molten metal

    ...more
    Get Best Price
  • Deoxidation Tubes

    Deoxidation Tubes

    Request for Price

    We are offering deoxidation tubes magnesium based deoxidiation tubes used to remove oxygen from copper based alloys.

    ...more
    Get Best Price

Services

  • METALLURGICAL CONSULTANCY

    METALLURGICAL CONSULTANCY

    Request for Price

    We Provide Consultancy for :- 1. Developing Brass Ingots for CP Fitting Industry 2. Decreasing Metal Loss in Copper and its Alloys'Melting. 3. Removing Defects from Copper and its alloys'Casting. 4. Identifying the Defects being faced and suggesting probable Solution.

    ...more
    Get Best Price

Be first to Rate

Rate This

Select the service for which you are writing review for this business

How would you rate the business?

What would you like other to know about this business, based on your experience?

Minimum 20 characters!

About the Company

  • Primary Business Retailer
  • Secondary Business Type Manufacturer / Exporters / Service Providers / Wholesale Suppliers
  • Year of Establishment 2009
  • No. of Employees Below 20
  • Annual Turnover Rs. 0.5 to 2.5 Crore Approx.
  • Ownership Type Partnership

Opening Hours

  • SUN : Closed
  • MON : 9:30 AM - 6:30 PM
  • TUE : 9:30 AM - 6:30 PM
  • WED : 9:30 AM - 6:30 PM
  • THU : 9:30 AM - 6:30 PM
  • FRI : 9:30 AM - 6:30 PM
  • SAT : 9:30 AM - 6:30 PM
We, at SEFSO, introduce ourselves as Manufacturers of Foundry Fluxes for Ferrous as well as Non-Ferrous foundries. In brief, SEFSO is a solution provider for all casting related problems being faced in foundries. We are associated with foundry industry since 1974. We believe in everlasting relationship building and never ending customer service.
Our Mission is to be a world class foundry solutions provider and generate valuable gains for all the stakeholders involved.
We have expertise in Foundry/Casting Fluxes for Copper & its alloys to be used in all techniques of Die/Sand Casting.
Our Product SEFREFINER (Boron based Grain Refiner) has been proved a Total Success amongst all the Brass & other Copper based Alloys’ Manufacturers.
Other than SEFREFINER, we have couple of more products in our Portfolio i.e.SEFCUPEX (Melting Flux), SEFCOTE DGL (Graphite Based Diecoat Paste), NOGAS(Degasser Briquette) etc.
Our Mission is to be a world class foundry solutions provider and generate valuable gains for all the stakeholders involved. Our team of efficient workforce leaves no stone unturned to design and manufacture. We are a customer-focused organization having prime objective to garner 100% customer satisfaction. We have the expertise to identify the needs of the customers and serve them accordingly.
Read More »

Contact Information

SEFSO

  • Mr. Puneet Kapoor
  • 20, New Shastri Nagar, Jalandhar, Punjab
top