AC Synchronous Motors Dealers in Mumbai (12 products available)

• Type: Ac Synchronous Motors
• Application: Servo stabilizer, valve actuator, packaging machines,printing machines
• Weight: 10-20kg
• Color: Blue
• Voltage: 220V
• Condition: New
• Automatic Grade: Manual
• Power: 9-12kw
• Driven Type: Electric
• Phase: SingleTwo
• Current Type: AC
• Speed: 60rpm
• Country of Origin: India
• Brand Name: Pro-Syn
• Frequency: 50
• Efficiency: 50%
• Continuous Current(A): 0.1-3A

• Low speed: 60 RPM.
• Max. Current inAmps: 0.10

A.C.Synchronous Motors Identical Starting & Running Currents. Instantaneous Start, Stop & Reverse. Residual Torque always present. No damage due to stalling.

'Vishal SYN' Reversible A.C. Syn. motors are Ungeared low speed 60 RPM @ 50Hz. & offering large torque range from 2kg-cm to 60   kg-cm in three NEMA frame sizes viz. O.D. 2.3. " (58 mm), 3.4 " (86 mm) & 4.2" (108 mm) and in 10 different models. The motor consist of 3 lead two phase wound stator & permanent magnet rotor.   FEATURES   Instant start, stop & reversible. Low speed 60 RPM @ 50 Hz. Torque from 2 kg.cm to 60 kg.cm (10 models). Insulation Class-B. starting, running & stalling currents are same. Magnetically rotor can be locked by D.C. applying. Power coated cast aluminum body with steel shaft.       CHARACTERISTICS     1) A.C. Operation : motor can be directly connected to 240 V;50Hz, supply along with factory supplied R-C network in series with one of the stator winding. Change of this R-C network from one winding to other results reversal of motor direction. Single pole three position switch can be used for Forward, Reverse & Off control as shown in the following diagram. Metal varistor oxide may be used to minimize the switch contact arcing.   2) Starting : Motor start within 1 1/2 Cycles of its applied frequency & will reach 60 RPM within 5 to 30 mS at 50 Hz. Since motor has no significant current rise on starting, this motor is ideal to an application which requires six or more starts per minute.     3) Stalling : Motor will not be overheated if stalled because starting, full load and no load currents are same. However prolonged operation against a solid stop will eventually produce bearing failure due to the resultant shaft vibrations.     4) Inertia Limitations : Since the motors are having extremely rapid starting, there is a limit to the inertia load at which the motor will start from rest. Addition of resilient coupling with app. 5 degree of rotational freedom or gearing with backlash between motor & load can increase the permissible inertia load handing capability.     5) Phase Shift Network : The values of R-C network have considerable effect on motor performance. They have been chosen by 'Vishal' in such a manner that no reverse torque is produced when voltage is applied. R-C values should not be varied more than 5% so as to enhance smoother starting, give quieter operation, maximize torque & improve efficiency.Other values may be recommended by the factory for the continuous duty specific OEM application   6) Stopping & Holding (Braking) : Due to magnetic rotor, these motors decelerate faster than conventional motors & stop within 5 degree after turnoff with no external inertia. Application of D.C. supply to one or both motor windings after removal of A.C. supply results deceleration time 1/10th to 1/20th those available with conventional motor & the motor shaft is electrically locked after the stop. A typical circuit for applying, stopping & or holding current is shown in the following diagram.   7) Back Driving : These motors act as generators when back driven. Rotating in access of 1400 RPM is not recommended because high voltages can be generated. At 1400 RPM or below suitable precautions for protection of personnel/phase shift capacitor & any other connected circuitry may be necessary when back driving.         8) 60 Hz Operation : These motors may be operated on 60 Hz, but may require a different R-C network, the factory must be consulted. Torque rating should be similar to those shown for 50Hz & speed is 72 RPM @ 60 Hz.

Pro-Sync AC synchronous motor is classified as permanent magnet induction motor, being operated as A C synchronous motors constant low speed motor or as a phase switched D.C. stepper. This motor is simple in construction including motor 60 rpm. The motor consists of a rotor & stator, which makes no physical contact, by maintaining a precise air gap. The simple construction leads to long life of the motor. Pro-Syn is a very special type of motor having the following advantages: Simple Circuitry Bi-directional control Instant start, stop and reversibility Starting and running currents are identical No damage even if the motor is stopped forcibly AC Motors Pro-Syn A C synchronous motor including 60 rpm is basically two phase motors. In order to operate from single phase AC source, second phase is generated by using RC network in series with one of the motor phase windings. Suitable RC network is supplied with motor. The instant starting, stopping and reversing characteristics of these motors have low speed of 60 RPM at 50 HZ, supply. The motors require single pole, three position switch to provide forward, off & reverse control. When the power is applied windings are energized, with no current being conducted to the rotor, Hence practically starting, running and stall current is not exceed the maximum torque of the motor specified. These motors are available in range of 3 Kgcm to 80 Kgcm capacity. AC synchronous motor manufacturer, exporter, trader, supplier and dealer from last 20 years with positive feedbacks from clients.

We are offering ac synchronous motors. 'vishal syn' reversible a.c. Syn. Motors are ungeared low speed 60 rpm @ 50hz. & offering large torque range from 2kg-cm to 60 kg-cm in three nema frame sizes viz. O.d. 2.3. " (58 mm), 3.4 " (86 mm) & 4.2" (108 mm) and in 10 different models. The motor consist of 3 lead two phase wound stator & permanent magnet rotor.

We are offering ac synchronous motors. Bi-directional. • actuators. • instantaneous start, stop & reverse. • remote control of switches. • identical starting & running currents. • winding machines. • residual torque always present. • machines tool applications. • no damage due to stalling. • valve controls. • low speed of 60 rpm

AC Synchronous Servo Motor 130mm 1.5kw, Three Phase CG AC Drive

ac synchronous motors, isolated transformers

ac synchronous motors, Self Locking Stainless Steel Cable Tie

Heavy Inline Gear Motor, ac drive, Shaded Pole Motor, Worm Gearbox

ac synchronous motors