Gala Thermo Shrink Pvt Ltd. Kandivali, Mumbai, Maharashtra

GSCYG range of tubing is extremely flexible, flame-retardant, thin wall with yellow and green striped heat shrink polyolefin tubing especially for electrical equipment ground lead applications. The unique dual color striping of yellow and green provides an instant identification for ground wires.

Tensile Strength : 16 N/mm2 (Min.)

Angleboots are Heat Shrink Right Angle Straight Boots provide insulation to the bushings in the cable termination box, where the clearance between phase to phase and phase to earth is less then the normal air clearance. These boots provide protection against flashover in the event of high humidity, rodent menace and surge impulse.The boots are mode from high quality cross linked non tracking polyolefin material. They are internally coated with water resistant red mastic.

Heat Shrink Cable Repair Sleeves is manufactured from High Quality Cross-linked polyolefin material. Heat Shrink Cable Repairing Sleeve is an adhesive lined, wraparound heat shrink that can be easily applied without the need for disconnection. It provides superior environmental sealing, rugged mechanical protection and high performance electrical insulation.Provides permanent waterproof barrier & environmental seal.

As the major producer of PVC caps in the world, Galathermo has the widest line of caps, plugs, flange covers, and products available. Of course, this broad line of products evolved due to the individual compensation that plugs have over nearly all hard plastic closures.

As the major producer of PVC caps in the world, Galathermo has the widest line of caps, plugs, flange covers, and products available. Of course, this broad line of products evolved due to the individual compensation that plugs have over nearly all hard plastic closures.Vin cap is made from specially formulated Poly Vinyl Chloride material.

Insulcover is a Medium Voltage Wrap Around Overhead Line Cover that provides retrofit insulation for overhead conductors to help prevent electrical outages caused by trees or wildlife coming into the contact with distribution lines.It is manufactured from high quality Non Tracking Polyolefin material.IInsulcover is designed to insulate existing bare lines without costly conductor replacement expenditure or additional line hardware. Insulcover may be applied selectively on problem spans when temperatures are above 0oC.

Tensile Strength : 10 N/mm2 (Mpa) (min.)

GPO E - 1524 - Series Class I termination kits are Heat Shrinkable Outdoor Termination kits designed for 3 Core Screened, Paper Insulated Lead Sheathed Armour Cable UPTO 24kV .

Insultube - Red is used in Power Cable Joints for MV Applications.These tubes are manufactured from high quality cross linked polyolefin material.Excellent Di-electric properties.Customised dimensions, thickness, length & colours available on request.

Anode cap is Heat Shrinkable Cap, used to seal and protect the critical connection between the lead wire and anode. It provides stress relief, moisture proofing and electrical insulation at the lead wire exit point. It is the ideal solution to the problem of premature system failure due to corrosion causing lead wire to come out of the anode. It is made from a highly Cross-linked Polyolefin material. Rubber based mastic coating inside the cap adheres to Anode material and wire insulation which provides water tight sealing according to IP 68 (Ingress Protection).

Insulcap is used to seal the ends of all types of Heat Shrink Cable End Caps to protect from ingress of watermoisture. The caps are manufactured from high quality cross linked polyolefin material.Compatible with most commonly used Cable Jackets i.e. XLPE, PVC, PILC or Rubber Sheathed Cable.Hot Melt adhesive lining provides permanent seal on irregular cable sheaths.Excellent resistance to weathering, moisture, contamination and adverse environmental conditions, according to IP 68 (Ingress Protection).Tamper Proof Application: Custom Logo Print with special non- removable Ink marks permanent seal on End Cap after Shrinking, thereby avoiding claims in case of Pilferage of Cable length.

Insulcap is used to seal the ends of all types of Heat Shrink Cable End Caps to protect from ingress of watermoisture. The caps are manufactured from high quality cross linked polyolefin material.Compatible with most commonly used Cable Jackets i.e. XLPE, PVC, PILC or Rubber Sheathed Cable.Hot Melt adhesive lining provides permanent seal on irregular cable sheaths.Excellent resistance to weathering, moisture, contamination and adverse environmental conditions, according to IP 68 (Ingress Protection).Tamper Proof Application: Custom Logo Print with special non- removable Ink marks permanent seal on End Cap after Shrinking, thereby avoiding claims in case of Pilferage of Cable length.

Bus boot is flexible electrical insulating boot shroud for busbar and switchgear connections upto 36KV. These pliable boots can be installed, removed or replaced in few minutes. Made from specially formulated Polyvinyl Chloride (PVC) material to provide excellent electrical insulation and to withstand higher operating temperature continuously.Busboot provides reduction in air clearance, which helps designing compact panels; thereby reduces the material costs by. saving in busbar lenghs, sheet metal components, etc.

Tensile Strength : 12 N/mm2 (min.)