Vac Sorb Polishing Machine
Mainly used for polishing kinds of electric plate. Functions : 1. vac sorb, convenient. 2. Subpressure switch protect 3. subpressure protecting when start and stop Main Technical Parameters 1. Power supply: Triphase 380V, 50Hz 2. Rated power: 800W 3. Air supply: 5-7kg/cm2 4. Size (LxWxH) :600x600x1100 (mm) 5. weight: 11Okg
...moretubular heater bending machine
It is used to bend the tubular heater which used in soymilk maker. Functions : 1. Easy operation, convenient maintenance. 2. Stable performance, bend 3pcs tube at one time. 3. Hydraulic drive, high production Main Technical Parameters : 1. Power supply: tri-phase 380V±1 0% ,50HZ 2. Power: 4KW 3. Hydraulic pressure: :≤ 65kgf/cm2, 4. Size: 1520•6500•2300mm
...moreTube rolling machine
TL - 101 Tube rolling machine is used for compacting elements in order to increase the density of MgO. It has been well-received in France, Japan and other countries. Functions : 1.The frame of this machine is made out of pig iron casting. The rocker die and tank are integral linear cutting. This machine is also equipped with fine-tuning dial, automatically removing sundries device and automatically cooling system. 2. According to the tube size and your special requirements, we have two types of motor of pinch roller for your choice. They are non-uniform speed (different speed) and uniform speed. The former make the tube better ductility, while the latter applies 10 the lube with large diameter. 3. When the tube specifications changed, we only need to replace a set of pinch rollers. The pinch rollers can be classified into two categories: high speed steel and tungsten carbide alloy. 4. Automatically stop when clogging. 5. This machine is of small size, low noise, convenient adjustments. 6. Applicable tube: Copper, iron, aluminum, stainless steel, etc. Main Technical Parameters 1. Tube diameter after compressing : Φ5.2mm - Φ19.0mm 2. The max. diameter before compressing : Φ21mm 3. The min. length of tube : 110mm 4. Efficiency : 18m/min 5. After compressing, the straightness can reach : -1:300 and the roundness can reach : 0 0.07
...moreTUBE FEEDING AND TESTING MACHINE
Is used to test the tube by high voltage and then feed the tubes into tube rolling machine automatically. Functions : 1.PLC controlled automatically. It feeds the elements with a consistent space between them. 2.Easy to operate, no operator is required. 3.Test tubes by high voltage and separate the undesirable element automatically. 4.The feeding speed is adjustable, preventing any jam ups. Main Technical Parameters 1. Power supply: 220V,50Hz,60W 2. Air supply: 5 -7kg/cm2 3. Feeding speed: 5-15m/min. 4. Applicable tube diameter: Φ6.5mm - Φ21.0mm 5. Applicable tube length: 1OOmm - 3000mm 6.Size (LxWxH) : 1400x850x1100(mm) (one meter machine) 7. Weight : 200kg
...moreThree Center Guarantee Filling Machine
Is used to fill the tubes with MgO, It is applicable to long tubes. Functions : 1. PLC automatically controlled, human-computer interface and control the oscillation frequency by electron speed regulator 2. lt adopts three guide tubes structure which has solved the problem that it is difficult to guarantee the center degree of long tubes 3. lt adopts self-locking powder device which assure that almost zero MgO loss. 4. Vibrator guarantee the powder density and the density could be above 2.20g/cm3 5. The guide tube moving speed controlled by frequency control. 6. Big and small powder box design. Electronic adjusting the exerted length of terminal pin. 7. indicate how to clear fault automatically. 8. 12,18,24,36 and 48 position machines are available to suit customer's production requirements. 9. Tube diameter : below Φ16mm, tube length:beow 6000mm. lt can be custom-made. Main Technical Parameters 1. Power supply: 220V, 50Hz 2. Rated power: 2.0KW 3. Air supply: 5 -7kg/cm2 4. Efficiency: 6500pcs/8h(tube length 250mm) 5. Size (LxWxH) : 1800x850x3300(mm) (1meter tube) 6. Weight: 600kg
...moreTerminal Pin Grinding Machine
is one of the terminal pin processing equipments. It is used to groove the ends of terminal pin. Functions : Stepless motor controls the speed. Main Technical Parameters 1. Power supply: Triphase 380V 50Hz 2. Rated power:750W 3. Applicable diameter:Φ1.5mm - Φ3.0mm ( It can be custom-made) 4. Applicable length: 40mm - 140mm ( It can be custom-made) 5. Efficiency: 60000-70000pcs/8h 6. Size (L * W * H) : 810*680*1140 (mm) 7. Weight: 21Okg Tube Rolling Machine TL
...moreStraightening Machine
Is used to straighten kinds of annealed tubes or rods. Functions : 1. The height and angle of rollers are adjustable, can satisfy kinds of specifications. 2. Adopts hyperboloid roller design which can improve the surface and roundness of tubes. 3. Six durable alloy tool steel rollers. 4. Easy to operate. Main Technical Parameters 1. Power supply: Triphase 380V, 50Hz 2. Rated power: 1.5KW 3. Applicable tube diameter: Φ5mm - Φ21mm (over this range can be custom-made) 4. Applicable tube length: ≥250mm 5. Size (LxWxH) :1300x700x1200(mm) 6. Weight: 360kg
...moreShaped Tube Bending Machine
Is an intelligent machine which can bend various shapes of tubes. Functions : 1. 14" touch screen, operation instruction is attached. 2. PLC automatically controlled, change the parameters according to your requirement. 3. Servo motor controls bending and feeding, the speed, angle and length are all adjustable. 4. Pneumatic clamping. can bend 1 -4pcs tubes at a time. Main Technical Parameters 1. Power supply: Single-phase nov, 50Hz 2. Rated power: 4KW 3. Air supply: 5 -7kg/cm2 4. Applicable tube diameter: Φ6.0mm - Φ1Omm 5. Size (LxWxH) :1650x900x1450 (mm) 6. Weight: 1000kg
...moreSemiautomatic Tube Cutting Machine
Is used to cut copper, iron, stainless steel round tubes Functions : 1. Pneumatic clamping, start cutting automatically. 2. Element rotates, automatically stop when loading finished, 3. Burr-free ends on the tubes, high efficiency, easy to operate. Main Technical Parameters 1. Power supply: Triphase 380V, 50Hz 2. Rated power: O,8KW 3. Air supply: 5 -7kg/cm2 4. Efficiency: 8000pcs -1OOOOpcs/8h 5. Size ( LxWxH ) : 800x500x900(mm) 6. Weight: 120kg
...moresemi automatic turning machine
mainly used to turn the ends of compressed tubes, and also can be used to turn and chamfer all kinds of tubes and rods in the hardware industry. Functions : 1. Pneumatic clamping and feeding. 2. Cutter rotate while the element not. safe and convenient operation. 3. Hydraulic speed governor control the turning speed,stable quality. Main Technical Parameters : 1. Power supply: Triphase 380V, 50Hz 2. Rated power: O.8KW 3. Air supply: 5 -7kg/cm2 4. Applicable tube diameter: Φ6mm - Φ12mm 5. Applicable tube length: ≥100mm 6. Efficiency: Above 5000pcs/8h(below tube length 500mm) 7. Size (LxWxH) :800x550x1000(mm) 8. Weight: 130kg
...moreSemi Automatic Stamping Machine
Mainly used to mark the straight tubes in circle or in linear. Functions : 1. Cylinder drive, easy to operate, no power supply require. 2. Tube diameter is adjustable. Main Technical Parameters 1. Air supply : 4-7 kg/cm2 2. Applicable tube diameter : Φ5mm - Φ20mm 3. Applicable tube length : ≥100 mm 4. Efficiency : 5000pcs - 8000pcs/8H 5. Size (L * W * H ) : 600*380*880 (mm) 6. Weight : 100kg
...moreSemi Automatic Polishing Machine
Mainly used to polish straight metal tubes and rods. Functions : 1. The tube diameter can be adjustable, easy to operate 2. Durable imported polishing roller. 3. Low noise, high quality. Main Technical Parameters 1. Power supply: Triphase 380V, 50Hz 2. Rated power: 1.7KW 3. Applicable tube diameter : Φ5mm - Φ20mm 4. Size (LxWxH) : 900x800x1000 (mm) 5. Can make multi-stations polishing machine to the requirement of customers 6. Weight: 200kg
...morePartial Annealing Machine
Is used to anneal kinds of stainless steel, copper, iron tubes. Functions : 1. Heating the tube surface by low voltage high-current short so that the MgO & heater will get little heat. 2. Time relay controls the annealing time. 3. Eight kinds of power and voltage can apply to various specifications of tubes. 4. Pneumatic clamping, safe and convenient. 5. Flexibie design of collet,. There will be little bend when heat extension. Main Technical Parameters 1. Power supply : Triphase 380V, 50Hz 2. Air supply : 5-7 kg/cm2 3. Rated power: 30KW 4. Applicable tube diameter: Φ6mm-Φ20mm 5. Applicable tube length: 150 mm -1000 mm 6. Size ( LxWxH ) : 1500x600x 1500(mm) 7. Weight : 500kg
...moreMultiturn Tube Bending Machine
Is used to bend multi-Coil, spiral, round, U-shaped tubes. Functions : 1. Stepped motor controlled, precise and adjustable angle. 2. PLC automatically controlled, easy to operate. 3. Pneumatic bending, high efficiency. 4. Simple structure and easy to change the specification. Main Technical Parameters 1. Power supply : Triphase 380V, 50Hz 2. Rated power : 800W 3. Air supply : 5 -7kg/cm2 4. Efficiency: 6000pcs/8h 5. Applicable tube diameter : Φ6.0mm - Φ8.0mm 6. Size (LxWxH) :1200x600x1500(mm) 7. Weight : 120kg
...moreManual Deburring Machine
mainly used to de burr and Chamfer kinds of rOund tubes and rods. Functions : 1. The tube diameter and length can be adjustable. 2. Deburr tube ends by high-speed wire wheel. 3. Easy to operate, high efficiency, good quality. Main Technical Parameters 1. Power supply : Triphase 380V, 50Hz 2. Rated power : 1.5KW 3. Efficiency : 20000pcs/8h 4. Applicable tube diameter. Φ4mm - Φ20mm 5. Applicable tube length : ≥150mm 6. Size (LxWxH) : 600x620x1200(mm) 7. Weight : 130kg
...moreHydraulic Tube Stretching Machine
Is used to stretch tubes with different length to equal length. Functions : 1. Advanced technology which cuts the cost 2. Hydraulic stretching, stable quality. 3. PLC automatic controlled. easy to operate. 4. Accuracy: + /-0.5mm Main Technical Parameters 1. Power supply: Triphase 380V 50Hz 2. Rated power:3.8KW 3. Air supply:5-7 kg/cm2 4. Applicable tube diameter: Φ6mm-Φ16mm ( It can be custom-made) 5. Efficiency: 5000pcs/8h 6. Size ( L * W * H ) : 4600*1200*1650 ( mm ) 7. Weight: 720kg
...moreFilling Machine TL
Is used to fill the tubes with mgO, and assure optimum centering of the coil in the element. Functions : 1. PLC automatically controlled, human-computer interface and control the oscillation frequency by electron speed regulator. 2. Powder filling density could be above 2.17g/cm3 Almost zero MgO loss. 3. Tube diameter : below 16mm; Tube length: below 3000mm. It can be custom-made. 4. Digital tube length adjustment. The guide tube moving speed controlled by frequency control. 5. lndicate how to clear fault automatically. 6. It can fill 24 pcs or 36 pcs tubes at a time. The efficiency can reach 6500pcs/8h ( take 250mm long tube for example) 7. 12,18,24,36 and 48 position machines are available to suit customer's production requirements. 8. Min. tube diameter: Φ5.5mm Main Technical Parameters 1. Power supply: 220V. 50Hz 2. Rated power: 1.5KW 3. Air supply: 5 -7kg/cm2 4. Efficiency: 6500pcs/8h(tube length 250mm) 5. It can fill 24 pcs or 36 pcs tubes at a time(beiow Φ10mm) 6. Size (LxWxH) :1200x800x3200(mm) (1meter tube) 7. Weight : 550kg
...moreDual Axis Strip Reeling Machine
Mainly used to reel radiation fins round the tubes. Functions : 1. Controlling the segment pitch by change gears. It is very precise and stable. 2. Two tubes at a time, high efficiency can up to 1.6~1. 7m/min.(5mm segment pitch). 3. Easy to operate and stable quaiity. Main Technical Parameters 1. Power supply: Triphase 380V, 50Hz. 2. Rated power: 750W. 3. Applicable tube diameter:
...moreDouble M Shaped Tube Bending Machine
Is used to bend the tubes to M-shaped,N-shaped,square and so on. Functions : 1. PLC automatically controlled, human-computer interface, bending tube parameters can be changed. 2. Load material manually. pneumatic clamping, bend 5 pcs at a time (Φ6.5mm) 3. Bend automatically according to the presetted parameter. 4. Main parts:Servo motor, reduction gear, ball bearing, precision return board and control 5. Applicable tube length: below 21 OOmm (over this range can be custom-made) 6. Applicable tube diameter: ΦP6.5mm - Φ12mm 7. Show how to clear fault automatically. Main Technical Parameters 1. Power supply : Triphase 380V, 50Hz 2. Air supply : 4 -7kg/cm2 3. Rated power : 5KW 4. Efficiency : 8000pcs -12000pcs/8h 5. Applicable tube diameter : Φ6.0mm - Φ12mm 6. Applicable tube length : ≤ 2200mm 7. Size (LxWxH) :2900x900x1700(mm) 8. Weight : 1000kg
...moreCircle Tube Cutter
Mainly used after tube making machine to cut the tube. Functions : 1. Test the speed and cut the tube automatically. 2. PLC automatically controlled, touch screen operation. 3. Encoder read the data of length which assure the precision of cutting length. 4. Even tube end and little burr. Main Technical Parameters 1. Power supply: Triphase 380V 50Hz 2. Air supply: 5-7 kg/cm2 3. Rated power: 2.8KW 4. Applicable tube diameter: Φ5mm-Φ12mm ( It can be custom-made) 5. Applicable tube length: 300mm -6000mm 6. Size (L* W * H) : 1800*700*1500 (mm) 7. Weight : 850kg
...moreAutomatic Tube Turning Machine
Is used to turn the tube ends according to the preseted length. chamfer and dig the powder of tube ends automatically. Functions : 1. PLC automatically controlled, human-computer interface. One man can operate three or four machines simultaneously. 2. The elements are automatically loaded, and then centered so the same amount will be cut from each end, thus ensuring that the original length can be maintained. 3. Show how to clear the error automatically. Main Technical Parameters : 1. Power supply : Triphase 380V, 50Hz 2. Rated power : 1.6KW 3. Air supply : 5 -7kg/cm2 4. Applicable tube diameter : Φ5.2mm - Φ 15mm 5. Applicable tube length : 110 - 1500mm 6. Efficiency : Above 5500pcs/8h(below tube length 500mm) 7. Size (LxWxH) : 2100x850x1350(mm) 8. Weight : 450kg
...moreautomatic tube making machine
Mainly used to weld a roll of stainless steel strip into a tube. Functions : 1. The frame of machine is made of excellent steel plate and of stable structure. 2. PLC automatically controlled, human-computer interface. 3. Control the speed by Mitsubishi transduction. The tube making speed can be adjustable. 4. Any error, abnormity or lack of material, the machine will alarm automatically. Main Technical Parameters 1. Power supply : TRiphase 380V 50Hz 2. Rated Power ; 16.5KW 3. Water Supply : 190 liters /hr 4. Argon Supply : 400-700 liters /hr 5. Hydrogen Supply : 20-350 liters /hr 6. Applicable tube diameter : Φ4mm - Φ16mm (over this range can be custom-made) 7. Applicable tube thickness : 0.17mm - 1.0mm 8. Tube making speed : 6-18m/min 9. Size (LxWxH) : 4000x1100x1700 (mm) 10. Weight : 2000kg
...moreAutomatic Tube Cutting Machine
Mainly used to cut copper, iron, aluminum, stainless steel tubes and rods. kinds of tubes with different shapes and different materials. Functions : 1. PLC controlled automatically, load and cut material automatically. 2. Two kinds of sawblade speed, pneumatic convert to hydraulic and the speed of sawblade is adjustable. 3. V-shaped collets move at the same time. ( Φ8.0mm tube, clamp 25pcs at a time) 4. Tube length after cutling: 200mm - 2300mm 5. Jaw opening: 1OOmm Main Technical Parameters 1. Power suppiy: Triphase 380V, 50Hz 2. Rated power: 1.6KW 3. Air supply: 5 -7kg/cm2 4. Efficiency: 30000pcs - 50000pcs (Φ8.0mm copper tube) 5. Size (LxWxH) :1500x800x1500(mm) 6. Weight: 550kg
...moreautomatic stamping machine
Mainly used to mark the straight tubes in circle or in linear. Functions : 1. Automatic feeding, no operator is required. 2. Tube diameter, length, print location can be adjustable. 3. Easy to operate, stable quality Main Technical Parameters 1. Power supply: Single-phase 220V, 50Hz 2. Rated power: 200W 3. Air supply: 5-7kg/cm2 4. Applicable tube diameter: Φ5mm - Φ20mm 5. Applicable tube length: 150mm -700mm (over this range can be custom-made) 6. Efficiency: 15000pcs - 20000pcs/8H 7. Size (L* W * H) : 1150*630*1200(mm) 8. Weight: 230kg
...moreBe first to Rate
Rate ThisOpening Hours