Mechanical Lab Equipment Dealers (292 products available)

• Size: 50-2000mm

1. Config ID: 50/ 80/ 100/ 150/ 200/ 300/ 450/ 600/ 800/ 1000/ 1200/ 1600/ 2000 mm. 2. Packing Type: Down Packing.3. Pressure: Continuous Air Supply.4. Filters: Sintered Mesh 2/ 5 micron.5. Liquid Contact: PTFE/ SS 316 L.6. Frit Locking: Chain Locking.7. Safety: Auto pressure cutoff.

• Journal Bearing: 70mm dia (Nominal) 75mm dia.
• Weights: 4 adjustable weights.
• Recommended oil: SAE 10
• Motor: D.C. shunt wound Speed range 500-3000 m rev/min  in both the directions
• Control Unit: Special design
• nometer Panel: 18 tubes mounted on a wooden back board

DESCRIPTION: The apparatus consists of a plain steel shaft encased in a bearing and directly driven by a small electric motor. The bearing is freely supported on the shaft and sealed at the motor end.The motor speed is precisely controlled and adjusted by specially designed control unit and can be run in both the directions.The bearing contains twelve equispaced pressure tapping around its circumference and four additional ones along its topside and on a vertical radial plane. All are connected by light and flexible plastic tubes to the rear manometer panel so that pressure head of a oil at all sixteen points can be clearly observed at all times.Oil is supplied to a low pressure region at both ends of the bearings by an adjustable reservoir fitted at the side of the rear panel.The bearings can be loaded by attaching various weights to the arms supported beneath it.  A label is conveniently provided at the front of the apparatus. SPECIFICATIONS:

Tom 106: coriollis component of acceleration description:- the set-up is designed to study coriollis component of acceleration of slider crank mechanism. Here the mechanical slider system is replaced by a continuous steam of water flowing through a steady rotating pair of tubes. These tubes can be rotated at various speeds by using a swinging field motor which also acts as dynamometer. A perspex window on top of tank gives clear view of the process and prevents splashing of the water over the side of the tank. The dynamometer continuously measures torque applied to the rotating tubes. The equipments are self contained, water re-circulating, provided with its own speed control unit and separate water circulating pump. Experiments:  to determine coriollis component of acceleration at various speeds of rotation and water flow rates. Utilities: -  water supply & drain  electricity supply: single phase, 220 vac, 0.5 kw technical specification: -  main tank : fabricated out of stainless steel grade  rotating arms : 9 mm 6 mm orifice diameter, length 30 mm  rotameter : 300 to 3000 lpm  electric motor : swinging field type, variable speed.  pump : fhp  control panel : rpm indicator with proximity sensor rpm measurement speed control unit on off switch, mains indicator etc.  the whole set-up is well designed and arranged in a good quality painted structure

• Application: Testing Machine
• Power: Hydraulic
• Application: teaching Apparatus and Testing Instruments
• Port: Delhi
• Place of Origin: Haryana, India
• Supply Ability: 30 Unit/Units per Month
• Model Number: SUPERB

We are main supplier of this product.

• Voltage: 220V, 230 volt
• Automation Type: Automatic
• Size: 13 Inches

Carrier size 13" *13" fitted with geard motor with concentric motion along with timer switch range 0 o 15 mintutes.

• Dimensions: 37 x 65 x 40 cm
• Temperature: 80°C to 0.5°C

Capillary Tube Viscosimeter The apparatus allows Poiseuille flows to be investigated and enables precise measurements to be made of the dynamic viscosities of liquids maintained at constant temperature, using the readings of a single pressure and a recorded time interval. The liquid whose flow characteristics are to be investigated is placed in a removable thermostatically controlled vessel which may be pressurised. The vessel supplies a capillary tube which is also thermostatically controlled and interchangeable. The level of pressurisation of the vessel and the temperature of the liquid can be continuously varied as required ; the liquid is continuously stirred to ensure that its temperature is uniform. Teaching objectives From the measurement of flow rate and of loss of head along the capillary tube, the following may be investigated using the viscometer : Poiseuille flow of a liquid of known viscosity. Measurement of the dynamic viscosity of a liquid and its variation with temperature. Shear stresses in viscous liquids and friction forces in laminar flow in tubes. Precise determination of the diameter of a capillary tube. Technical specifications The following instrumentation is provided with the apparatus : A mercury manometer. A thermometer.

• Electrical Supply: 220-240V/1ph/50Hz, 1A
• Length: 1.60m
• Width: 0.60m
• Height: 1.45m
• Warranty: 2 Years

Mechanical engineering is a discipline of engineering that applies the principles of physics and materials science for analysis, design, manufacturing, and maintenance of mechanical systems. It is the branch of engineering that involves the production and usage of heat and mechanical power for the design, production, and operation of machines and tools. It is one of the oldest and broadest engineering disciplines.

We have developed several offline as well as online options for the convenience of clients to ensure faster trade. Being a quality-conscious firm, we are offering nothing short of the best quality products from Ambala(India).

Consists of a full length metal upright 245cm long graduated in cms, to be mounted vertically near a wall by means of two brackets. A light weight accurate frictionless wheel of 10cm dia is mounted on it's top. Three adjustable clamps move along the rod. Upper carrying a ring and lower carrying a platform and the third is equipped with electric release system. The unit is all metallic and complete with two sets of falling weights and rider weight.

• Condition: New
• Warranty: 1 year
• Power Source: Electric
• Carrier Size: 13
• Operated on: 220/230 Volts.
• Finish: Polished

Rotator Variable Speed, carrier size 13. fitted with geared motor with concentric motion along with time switch range 0 to 15 minutes.

• Type: VDRL
• Material: Stainless Steel
• Application: Laboratory
• Voltage: 220V
• Frequency: 50-60 Hz
• Power Source: Electric
• Automation Type: Automatic

Suitable for VDRL and other agglutination tests, blood grouping tests and for mixing of solutions in small flasks, beakers or bottles. Body made of sturdy mild steel sheet duly finished in stoving enamel paint. Tray type platform size 300x300 mm can take cavity slides, bottles, flasks etc.for shaking at a fixed speed, by the help of spring wires. Standard fixed speed 180 RPM An automatic 60 minutes timer can be provided against extra cost as optional by which shaking duration can be set. To work on 220V AC 50 Hz single phase.

We are offering Refrigeration Tutor, 196x93.

Operated on 220/230 volts, VDRL Rotary Shaker with timer is widely used in various laboratories. Made from certified components, in accordance with all industry standards, VDRL Rotary Shaker are highly appreciated for competitive prices. We are a reliable Manufacturer and Supplier of highly functional VDRL Rotary Shaker with long service life. VDRL Rotary Shaker is fitted with geared motor with concentric motion along with time switch range 0 to 15 minutes. For timely delivery, contact us.

Load capacities from 10 to 50kN Self alignment & self locking feature eliminates requirement of alignment fixture&mechanical wedge washers Ideal for Low cycle fatigue and tensile tests Designed as per ASTM E 606 and meets E 1012 for alignment High temperature version up to 10000C

• Certification: ISO 2001-2015
• Color: Blue
• Voltage: 440V
• Warranty: 1year
• Brand Name: UNIVERSAL
• Weight: 30000 KGS.
• Automatic Grade: Manual
• Production Capacity: ANY
• After-Sales Service Provided: YES

we manufacturre mechanical equipments used for treatment of wtp,stp and etp like clarifiers, clariflocculators, pressure sand filters, dual media filters, flash mixers, agitators, rate of flow indicators, loss of indicators, surface aerators, chalorination system, air blowers, etc.,.

• white: white

Baseline® mechanical pinch gauge has a 60 pound capacity. Unit has a red body. The pinch gauge allows for measure tip, key and palmer pinch strength in both pounds and kilograms. Measurements are accurate and repeatable. The Baseline® pinch gauge is made in USA and results are consistent with published Markowitz studies. Maximum force indicator remains at the maximum reading until reset. The strength reading can be viewed as pounds or kilograms. CE Certified. Comes in a protective carrying case

• Displacement relative error: ±1%
• Voltage: 220V 50Hz

Applicable for all kinds if metal materials, nonmetallic materials, fabrics, plastic grid for tensile, bending, shearing, tearing, bursting, pierce, stripping detection etc. � Multiple functions, fully automatic, light weight, convenient operation � UTM adopts DC speed regulating servomotor and reduction gears as the power source.

.To demonstrate the basic vapour compression cycle of refrigeration. To study theoretical cycle and plotting T.q. and P.H. charts. To study the properties at salient of the cycle. To find out refrigerating effect and work input hence actual and theoretical C.O.P. Space Required : 2m. x 1.5m.

This set up is designed to study coriollis component of Acceleration of a slider crank Mechanism. The apparatus uses hydraulic analogy to represent the rotating slider. It consists of a rotating block with two arms in opposite direction. These tubes can be rotated at various speeds by variable speed motor. A Perspex window on top cover helps to visualize the process. Rotameter is used to measure water flow rate through tubes. Water is circulated by small mono block pump. Specifications: Main Tank with fibre glass lining. Rotating Arms 9/6 mm dia, 300 mm long. Motor - Variable Speed D.C.Motor. Rotameter. Mono block Pump. Control Panel comprising of - Speed Control Unit. Speed Indicator. Voltmeter. Ammeter. Necessary switches. Rigid support frame. Range of Experiment : Coriollis Component of Acceleration can be determined at various speeds of rotation and water flow rates. Service Required : A.C,Single Phase .230 V. stabilized supply.  

• Condition: New
• Color: White, Blue, Yellow, Clear
• Brand Name: SCS
• Features: Shear strength, Precise design, Fine finish .

Shambhavi impex is offering mechanical engineering equipment in india.