Jetex Industries Ghatkopar, Mumbai, Maharashtra

Cold Galvanizing Coating With Brilliant Shiny Finish To That Of Hot Dip GalvanizingZINKOTE is a high performance zinc and aluminium coating designed to provide true galvanic corrosion protection to metals and stop rusting.It air dries fast on application to leave a film that is highly resistant to heat, water, corrosion and saline environments. It bonds to bare metals without requiring any baking and offers maximum protection against corrosion under severe conditions. It does not contain any chlorinated solvents, CFCs or ozone depleting chemicals Benefits Repairs damaged hot dip galvanised surfaces Fast air-drying and offers protection of hot dip Galvanizing Brilliant metallic finish to that of hot dip Galvanizing Highly abrasion resistant film does not peel off Offers long-term protection Prevents rust & corrosion ApplicationsStructural steels, transmission towers, welding seams, bridges, relay towers, piping & ducting, offshore equipment, nuclear & power plants, antennas, metal fabrication, industrial maintenance, touch up to damaged galvanised coatings. DirectionsFor Use Clean and degreased the surface prior to application. Remove all rust and loose scales by wire brush. Shake can well for a couple of minutes till bearing noise from inside the can is audible. Repeat the same before every application. Spray light, even coats with sweeping action of the hand onto completely dry surface. Allow solvents to completely evaporate before re- application. Optimum desired film thickness is about 2-3 mils. Drying time to touch is about 10-15 minutes, to handle is about one hour and for complete cure is about 24 hours. Flush away paint products or product residues in the dip tube of the valve by cleaning it. Cleaning of the valve should be performed after spraying is finished, by inverting the can and pressing the actuator button in short bursts till only the propellant comes out. If required, to prevent clogging, remove the actuator button and clean the button orifice with a thin, fine wire. Caution Contains flammable solvents and propellant. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

Type : Single Pack System

Color : Silver

Packaging Type : 400 Ml Aerosol Spray

Shelf Life : 12 Months from Date of Manufacture in Sealed Condition.

Synthetic Lubricant & Cleaner for Precision Textile EquipmentYARNLUBE spray is a non-staining synthetic lubricant cum cleaner for textile machinery parts such as scissors and cutting mechanisms of knotters and splicers in weaving, winding, spinning, sewing and knitting machinery where mechanisms are intricate and delicate and operating speeds are high.It is useful for cleaning dirt, dust, fluff and provides a non-staining, anti static mild lubricating film for reducing wear and friction.YARNLUBE spray does not contain any CFCs or harmful ozone depleting substances.Benefits Clear & non-staining ultra thin film Cleans moisture, dirt, dust, fluff Penetrates metal crevices Provides mild lubrication Protects from corrosion No carbon residues   Directions for UseSpray evenly thin light coats on clean and dry surfaces. Allow the cleaning solvents to evaporate. Spray from a distance of 20-30 cms. Use extension tube for pinpoint application. CautionFlammable contents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.General Use in well ventilated areas. Avoid continuous breathing of Vapor and spray mist. In closed areas or areas with poor ventilation, use respiratory protection. For complete details on safety, short and long term exposure, refer to this product’s safety data sheet (SDS).DisposalAll used and unused product should be disposed of in accordance with state regulations. Handling Read instructions on the container label of the product before use. The product safety data sheet (SDS) contains the relevant information regarding personal protective equipment, safe use, physical and health hazards. Limited WarrantyThe information and data contained in this sheet is accurate to the best of our knowledge or is obtained from sources, tests or experiences believed by us to be reliable and accurate. User is responsible for determining whether recommended product is fit for a particular purpose. All products should be tested for suitability on a particular application prior to actual use. We make no representations of any kind. Data offered without warranty.

Type : Cleaner & Mild Lubricant

Color : Clear

Packaging Type : 500 Ml Aerosol Spray

Appearance : Liquid

Solubility : Nil in water

Shelf Life : 24 Months from Date of Manufacture in Sealed Condition

This is a fully formulated Synthetic Spindle Oil especially designed for the lubrication of spindles blended with antirust and antistatic additives to provide long life and extremely low friction performance. It is a non- staning synthetic oil which does not leave any carbonaceous deposit. Due to its excellent lubricity it reduces the power requirement of high speed spindle drives.Temperature range (-400°C to 1200°C).

a range of high performance specialty industrial lubricants for all types of industries..

Color : Black, Golden, Transparent, Yellow, COLOURLESS

Form : Gel, Liquid, SOLID

Packaging Type : Drum, Plastic Bottel, Plastic Can

Packaging Size : 1-10ltr, 20-30ltr, 40-50ltr, 210 LTRS.

Brand Name : JETEXINDIA

It is a synthetic grease compounded from fortified silicone oil thickened with a special lithium soap and E.P. Additives to meet the most critical Industrial applications, It is ideally suitable for very high speed and high temperature applications. It possesses an excellent, resistance to oxidation in corrosive atmosphere annd break down due to shear. It has outstanding water repellency characteristic for marine and humid atmosphere. It is far more inert and heat stable making it a life long lubricant. It is ideal for low torque bearings.

Omnilube is a fast acting industrial grade lubricant, rust Omnilube and corrosion inhibitor. It forms a clear thin non- drying lubricating film that penetrates deep into the minutest crevices to displace trapped moisture and leaves behind a protective film to seal out further moisture and corrosion. Its unique low surface tension formula rapidly attacks rust to free seized or frozen components. It is non-conductive, nonstaining and offers complete protection to metal surfaces indoors as a medium term corrosion inhibitor for protection against corrosion and moisture penetration for up to 12 months under normal storage conditions.Omnilube does not contain any silicones, ozone depleting chemicals, CFC’s or harmful chlorinated solvents and is safe for use on around all metals, plastics, rubbers and other industrial finishes.    Benefits Multi functional formula lubricates all sliding and moving parts with a long lasting thin oily lubricating film Rapidly penetrates minute cracks and pores to displace trapped moisture Penetrates deeply through rust to loosen scale and corroded or frozen parts Leaves a thin, long lasting film to prevent formation of rust or corrosion Cleans & removes oils, greases and other light contaminants Provides greaseless, non staining, silicone free lubrication and protection Contains safe non flammable CO2 propellant 360° Valve allows product to be sprayed in any position- even inverted   Applications A product as versatile as this has hundreds of multipurpose uses in all types of industrial, marine, aviation, electrical / electronic, electromagnetically, commercial and domestic applications. Lubrication: Thin, non-drying protective oily film effectively lubricates moving parts as tuners, micro switches, power tools, automation equipment, locks, vending machines. Rust Penetration: For rapidly loosening tight, rusted or frozen components with high penetrating action. Moisture Displacement: Rapidly dries wet ignitions & removes trapped moisture from electrical / electronic systems. Corrosion Protection: For dies, jigs, tools, relays, connectors, switches, instruments, finished welds, casings, shafts, motors, freshly machined surfaces. Cleaner: For dissolving and removing grease, oil and other light contaminants. Prevention: Of entry of further moisture.   Directions For Use - BulkApply by means of brush or by dipping component into the fluid. Allow solvents to penetrate and free rusted parts. Period for penetration may vary depending upon the length of time the product has been rusted for and in some cases may even take up to hours. Use an absorbent rag or a brush to remove dirt, rust, scales & dust. For moisture displacement, apply onto surfaces till only clear product (amber-pale straw) comes out and the emulsified residue is totally cleared. Never use on energized circuits or hot surfaces. Clean and dry surfaces completely before applying power. For metal protection, dip components or apply by brush and do not wipe off protective film from the surface.Directions For Use - Aerosol For rust penetration, spray liberally onto the surface. Allow solvents to penetrate and free rusted parts. Period for penetration may vary depending upon the length of time the product has been rusted for and in some cases may even take up to hours. Use an absorbent rag or a brush to remove dirt, rust, scales & dust. For lubrication, spray lightly and evenly over surface area to be lubricated. For moisture displacement, spray until clear product comes out and emulsified residue is totally clear. For metal protection, spray liberally and do not wipe off protective film from the surface. CautionContains flammable solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

Applications:Omnigear EP Gear Oils are 100% synthetic, heavy duty industrial PAgear oils intended for enclosed gears operating under adverse loads and temperatures. A variety of seven ISviscosities covers a wide range of temperature and load conditions.Characteristics: Reduced downtime due textended change intervals High viscosity index Wide temperature range -50F t+250F, depending on grade chosen Longer life than conventional oils. Intended for heavy-duty extreme pressure industrial applications. Meets the requirements of: U.S. Steel 224 David Brown S1.53.101 AGMA 250.04 Cincinnati Milacron DIN 51517 Part 3

Molybdenum Disulfide Lubricant For Extreme PressuresMOLYWET is a suspension of micro fine molybdenum disulfide solid film lubricant, extreme pressure additives and corrosion inhibitors in a special lubricating oil carrier. It deposits a thin, non-drying film of MoS2 onto the surface to form a low friction and wear reducing shield that eliminates metal-to-metal contact and increases wear life of the equipment. MOLYWET does not contain any type of solvents, CFCs or any ozone depleting chemicals.Benefits Very high lubricating effect Improves the extreme pressure and load carrying abilities of lubricating oils Reduces wear and friction Improves running in Eliminates frictional heat produced and prevents overheating Reduces operating temperatures and noise levels Increases relubrication intervals and reduces lubricant consumption Prevents galling, scuffing and extends wear life of equipment Passes through filters and does not clog them   Applications As a high speed, anti wear and anti friction lubricant for sliding parts in textile machinery such as Autoconer mechanisms operating under high speeds and humid conditions. Lubrication of cams, bearings, gears, pins, chains, sliding or mating parts, springs, cam followers, slides. For use as an additive to all types of mineral oils to enhance load bearing capacity and impart extreme pressure carrying abilities for minimising wear and excessive friction, for eliminating metal to metal contact, welding and seizure. Directionsfor Use Shake the can vigorously for a couple of minutes before spraying. Repeat before every application. Spray onto a clean, dry and degreased surface in thin light coats. Spray using extension tube for pin-point application.Caution Contains flammable solvents and propellant. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

Color : Black

Feature : Protection Against Corrosion

Condition : New

Form : Liquid

Packaging Type : Can

Packaging Size : 400ml

Type : Extreme Pressure Lubricant

Color : Black

Shelf Life : 24 Months from Date of Manufacture in Sealed Condition.

It is a semifluid, complex soap based high grade grease specially selected for its excellent response to variable speed drives to provide high antiwear and load carring capacities to the grease. It is also fortified with synergistic blend of other additives such as rust and corrosion inhibitors and antioxidants to provide an unsually good water repellency for rust protection and oxidation stability for high.

JETEX SWR-12 grease is based on a special highly heat stable silicone fluid and soap thickener along with additives to impart extreme pressure properties and prevent high temperature oxidation. This grease is capable of withstanding very high temperatures and maintains its consistency. It is inherently inert and possesses a high degree of shear stability and resistance to oxidation. It does not dry out, harden or melt even after long-term exposure to high temperatures and has very good resistance to water, steam, humid environments and chemicals. It is very effective for lubrication of bearings under light to moderate loads and metal and plastic surfaces.Benefits\n\nExtremely wide service temperature range of -40°C to +204°C\nExceptionally good oxidation resistance\nHigh shear stability\nDoes not thin out at high temperatures\nStable, chemically inactive and inherently more inert than petroleum based products\nResistant to ageing, water, moisture, steam, humidity and corrosive environments\nNon toxic and non staining\nLow evaporation and does not volatile at higher temperatures\nSafe for use on metal, plastic and rubber components (except those made of silicone)\n\nApplications For lubrication of rolling element bearings operating under light to moderate loads as in oven fans, exhaust motors, kiln pre-heaters, oil burners, textile slashers and driers, conveyors, washing machines, air conditioners, domestic appliances, data processing equipment, aircraft engines, radiator cooling fans, electrical motors, vacuum machines and plastic components.Method of Application Apply on all clean sliding surfaces by normal greasing methods i.e. by brush, grease gun or dispense via centralised lubrication systems. Do not mix with other oils or grease.

Shelf Life : 24 Months From Date Of Manufacture In Sealed Condition.

Dielectric, non-melting silicone grease like compound for electrical parts insulation and moisture protectionApplications\n\nAs a moisture proof seal and protective barrier coating on high tension electrical connections of all electronic, electrical, industrial, marine, aircraft, automotive equipment for providing greater resistance to tracking and effects of corona discharges\nAs a dielectric seal cum lubricant for switches, cables, cable connectors, high voltage insulators, battery terminals, plastic and rubber parts, bushings, electrical insulation, spark plugs, disconnection junctions, ignition systems to prevent formation of a conducting film of water, eliminate risk of flash overs, minimise electrical leakage and prevent ingress of moisture\nFor all electrical fittings exposed to marine environments to protect from salt-water corrosion, oxidation, moisture penetration, reduce maintenance and increase wear life of equipment As a protective coating on insulators and bushings in chemical plants to protect them from chemical fumes, vapours and gases\nAs an assembly lubricant for various metal-plastic and metal- rubber pairings\nOn to surfaces of ceramics, metals, insulating materials to impart high surface resistivity\n\nBenefits\n\nWide service temperature range from -50°C to + 200°C\nMoisture resistant and excellent water repellency qualities prevent formation of conducting water film\nHigh degree of resistance to salt spray, humidity and corrosives\nHigh dielectric strength\nChemically inert\nVery low volatility\nVery good thermal and oxidation stability\nConsistency is largely independent of temperature and maintains its grease like consistency at high temperatures\nNontoxic, non volatile, non melting and odourless\nCompatible with plastic, rubber and metal pairings\nVery good adhesion on all metals, glass, plastic, ceramic, rubber substrates\n\nMethod of Application Apply by means of hand, brush or putty knife. Can also be dispersed in solvents like mineral spirits, xylene or methyl ethyl ketone for thinning the consistency and making it easier to apply by brushing, dipping or spraying. Do not mix with other oils or grease.Directions For Use (Aerosol only) Shut off equipment and turn off power before spraying. Spray thin, light and even coats onto clean, dry and moisture free surfaces to a thickness of about 0.4-0.5 mm. For optimum use, clean surface dry from moisture. Allow few minutes for solvent to completely evaporate before resuming operations. Removal of the film can be done by normal degreasing solvents.Caution (Aerosol only) Contains flammable solvents and propellant. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

Shelf Life : 24 Months from Date of Manufacture in Sealed Condition.

Applications High speed stenter frames in textile industry, glass works, paint booths, automotive assembly lines, varnish curing booths, open chains in industry, steel plants, paper and plywood manufacturing units, ceramic processing plants, latex manufacturing plants, lubrication of all chains, clips, bearings. Benefits \n\nExtremely wide service temperature range from -10°C to +250°C\nVery good extreme pressure properties enhance load carrying abilities and reduces frictional wear\nExtremely low evaporation rate at high temperatures\nDue to its absolute synthetic formulation, there is no carbon or resinous deposit even at high temperatures\nMinimised deposit formation reduces cost related to chain cleaning such as labour, production loss and downtime\nLower evaporation rate reduces consumption and allows for extension of lubrication periods thereby cutting down on lubrication costs\nProvides superior lubrication and protection even when subjected to high temperatures and humid conditions\nDue to superior lubrication, power requirements are reduced resulting in both lubricant as well as energy savings\nCost savings due to reduction of parts premature wearing out and replacements are also greatly increased\nGood adhesive properties and water resistant\n\nMethods of Application For optimal lubrication and adhesion, clean and degrease the surface of all previous residues, lubricants or contaminants with JETEX DG-50 heavy duty degreaser. Apply to clean surface by regular oiling methods i.e. by brushing, spraying, dipping or drop feed oiling mechanisms. Allow time for lubricant to penetrate and excess lubricant to drip off before restarting operations. For new chains: Thoroughly clean prior to applying this lubricant. It is recommended to keep new chains dipped in the lubricant for 30 minutes to ensure complete penetration to all innermost points. Avoid excessive use. Do not mix or dilute with other oils or grease. Use as per instructions laid down in manufacturers manual. Replace cap after use.

Applications High speed stenter frames in textile industry, glass works, paint booths, automotive assembly lines, varnish curing booths, open chains in industry, steel plants, paper and plywood manufacturing units, ceramic processing plants, latex manufacturing plants, lubrication of all chains, clips, bearings.Benefits Extremely wide service temperature range from -10°C to +250°C Very good extreme pressure properties enhance load carrying abilities and reduces frictional wear Extremely low evaporation rate at high temperatures Due to its absolute synthetic formulation, there is no carbon or resinous deposit even at high temperatures Minimised deposit formation reduces cost related to chain cleaning such as labour, production loss and downtime Lower evaporation rate reduces consumption and allows for extension of lubrication periods thereby cutting down on lubrication costs Provides superior lubrication and protection even when subjected to high temperatures and humid conditions Due to superior lubrication, power requirements are reduced resulting in both lubricant as well as energy savings Cost savings due to reduction of parts premature wearing out and replacements are also greatly increased Good adhesive properties and water resistant Methods of Application For optimal lubrication and adhesion, clean and degrease the surface of all previous residues, lubricants or contaminants with JETEX DG-50 heavy duty degreaser. Apply to clean surface by regular oiling methods i.e. by brushing, spraying, dipping or drop feed oiling mechanisms. Allow time for lubricant to penetrate and excess lubricant to drip off before restarting operations. For new chains: Thoroughly clean prior to applying this lubricant. It is recommended to keep new chains dipped in the lubricant for 30 minutes to ensure complete penetration to all innermost points. Avoid excessive use. Do not mix or dilute with other oils or grease. Use as per instructions laid down in manufacturers manual. Replace cap after use.

Solid lubricants based grease paste for reducing wear and withstanding high pressures; metal freeApplications\n\nHighly recommended for use on all threaded and flanged connections operating at very high temperatures and corrosive conditions to enable faster and rapid non destructive disassembly after long operational periods as in autoclaves, furnace, boilers, reactors, turbines, extrusion mandrels, compressors, heat exchangers, gas generators, plastic molding machines, chemical, petrochemical, refining, iron and steel, wood manufacturing equipment.\nHeavy duty thread compound for studs, nuts, bolts, valve stems, spindles, exhaust pipes, cylinder and engine head screws, steam lines exposed to high temperatures, water, steam, saline, chemical and corrosive environments to provide complete protection from seizure and corrosion.\nUse for press fit joints, guides, sliding contact surfaces, door hinges, seals, spark plugs, springs.\n\nBenefits\n\nExtremely wide service temperature range of -40°C to +1500°C\nMakes disassembly very easy and non-destructive even after long operational periods at high temperatures and adverse working environments\nHigh load withstanding capacity and creates an effective matrix between mating surfaces to prevent metal-to-metal contact\nProtects surfaces from wear and friction\nGood corrosion protection\nLower breakout torque\nPrevents bolt breaking, sintering, fusion, seizure, thread striping and distortion of threads, stress cracking\nLow coefficient of friction\nReduces wear and increases service life of components\n\nDirections for Use Use as supplied. Never dilute or mix with other oil or grease. Clean and degrease the surface of all previous residues prior to application. With a wire brush, apply the paste in adequate quantity on the surface and right down up to the base stem of the thread. The excess paste need not be removed as it provides a good sealing effect.General Use in well ventilated areas. Avoid continuous breathing of Vapor and spray mist. In closed areas or areas with poor ventilation, use respiratory protection. For complete details on safety, short and long term exposure, refer to this product’s safety data sheet (SDS).Disposal All used and unused product should be disposed of in accordance with state regulations.Handling Read instructions on the container label of the product before use. The product safety data sheet (SDS) contains the relevant information regarding personal protective equipment, safe use, physical and health hazards.Limited Warranty The information and data contained in this sheet is accurate to the best of our knowledge or is obtained from sources, tests or experiences believed by us to be reliable and accurate. User is responsible for determining whether recommended product is fit for a particular purpose. All products should be tested for suitability on a particular application prior to actual use. We make no representations of any kind. Data offered without warranty.

Shelf Life : 60 Months from Date of Manufacture in Sealed Condition

Packaging Type : 1 kg container

Nickel based high temperature anti seize compound meeting purity levels for nuclear power plant equipmentApplications\n\nPrimary applications for JETEX NS-369 is in Nuclear PoPwer lants, Steel Plants, Petrochemical & Fertilizer Units, Refineries for providing high temperature, extreme pressure, anti seize and anti corrosion lubrication for equipment as burner tips, furnace hinges, reactor bolts, studs, pipe fittings, threaded connections, flanges, pump fittings, unions.\nIt can be used as a heavy duty anti seize thread compound for all high strength alloys, nickel alloys and stainless steel hardware or fittings to provide effective lubrication at high temperatures and prevent seizure.\nIt can be safely used in the presence of ammonia, acetylene or vinyl monomers that are unstable in the presence of copper.\n\nBenefits\n\nExtremely wide service temperature range from -30°C to +1427°C.\nEliminates metal to metal contact and maintains lubrication qualities under wide variations of temperature and adverse operating conditions and prevents galling, hardening, fretting, seizure, stripping, cold-welding, sintering, fusion of threads, bolt breaking and distortion\nEnables faster and rapid assembly and non-destructiv disassembly even after long term exposure to high temperatures and corrosive atmospheres\nDoes not contain any ingredients that may poison reactor catalyst beds such as copper, lead, sulfurs, chlorides, halogens, silicones\nHighly resistant to hot & cold water, brine water, steam, humidity, moisture, dilute acids and alkalis, rust, corrosion and oxidation\nSafe to be used in the presence of ammonia, acetylene and vinyl monomers which are highly unstable in the presence of copper Low friction properties reduce wear and friction to increase life of the equipment\nChemically inert and does not react with metals to cause pitting, and prevents intergranular or electrolytic corrosion of high strength ferrous or non-ferrous materials\nExtremely recommended for use on all high strength alloys, stainless steel and nickel alloys\nMeets purity levels for use in nuclear class hardware\n\nMethod of Application Clean and degrease the surface prior to application. Remove all coatings, greases, dirt, grime, loose rust and scales by means of a fine thin wire. Apply Nikkel Lube liberally by means of a stiff wire brush on to the surface and evenly right down to the roots of threads. Excessive compound provides a good sealing effect and need not be removed. Do not mix with conventional oils and greases.

Packaging Type : 500 g (brushtop) - 1 kg - 5 kg

Shelf Life : 24 Months from Date of Manufacture in Sealed Condition.

Copper and solid lubricants paste for all nuts, bolts, screws, threaded connections; lead and nickel freeApplicationsAnti seize, anti rust & effective lubricant for protection of parts operating under severe corrosion, temperatures and steam, humidity, water or chemical attack as: studs, nuts, bolts, screws, pipes, keys, u-bolts, splines, taps, slides, seals, slippers, joints, plugs, gears, chains, exhausts sprockets, valve stems, manifolds, couplings, adapters, bearings, gaskets, packings, drills, bushings, king pins, spindles. For use on all threaded and flanged connections operating at very high temperatures to prevent seizure, corrosion and atmospheric influences as in: cat crackers, autoclaves, cylinder heads, furnace bolts, generators, fuel feed nozzles, boilers, reactors, ladles in steel plant, turbines, burners, extrusion mandrels, ovens, soot blowers, blast furnaces, pumps, engines, steel plant equipment, compressors, heat exchangers. For use in oil rigs, refineries, petrochemical, chemical & fertiliser plants as a heavy duty thread assembly compound, pipe sealant and anti corrosion compound for components exposed to very high temperatures, steam, hot, cold, brine water, humidity, corrosive or chemical environments to provide protection, effective lubrication, sealing and corrosion protection and prevent seizure, jamming and rusting even after long operational hours under very severe conditions.For use in rotary kilns in cement plants as a high temperature, extreme pressure, low friction lubricant for effective lubrication of live ring supports.Benefits Extremely wide service temperature range from -18°C to +1100°C. Eliminates metal-to-metal contact and maintains lubrication qualities under wide variations of temperature, pressures and adverse operating conditions. Prevents fretting, galling, tightening, welding of mating surfaces. Protects against galvanic corrosion between dissimilar metals in contact. Enables faster and rapid assembly and non-destructive disassembly even after long term exposure to high temperatures and corrosive atmospheres. Prevents stripping and cold-welding of threads and avoids sintering, fusion, thread stripping, bolt breaking and distortion. Low friction properties reduce wear and friction to increase life of the equipment and avoid costly replacements. Highly resistant to hot and cold water, steam, humidity, brine water, mild acids and alkalis, corrosion, aging and oxidation. Methods of Application Clean and degrease the surface prior to application. Remove all coatings, greases, dirt, grime, loose rust and scales by means of a fine thin wire. Apply METAPLAT liberally by means of a stiff wire brush on to the surface and evenly right down to the roots of threads. Excessive compound provides a good sealing effect and need not be removed. Do not mix with conventional oils and greases. Note METAPLAT is not for use as a lubricant for high-speed bearings. However it may be used for lubrication of heavily loaded bearings under very slow speeds.

Packaging Type : 500 g (brushtop) - 1 kg - 5 kg - 20 kg

Shelf Life : 24 Months from Date of Manufacture in Sealed Condition.

Hydrraulliic HLP 32,, 46,, 68,, 100JETEX Hydraulic HLP grades are high performance anti-wear hydraulic oils specially formulated from premium quality solvent refined base oils and high performance additives and have excellent product stability with good anti-wear performanceApplication\n\nLubrication of industrial machinery\nHydraulic systems of mobile and construction equipment\nHydraulic systems fitted with vane, gear or piston pumps\nPlastic injection moulding machines\nMedium duty compressors\n\nBenefits\n\nExcellent filter life due to superior dry & wet filter ability\nLonger equipment life due to lower wear & tear of aggregates\nReduced equipment downtime\nTrouble free operation\n\nPerformance standardsThey exceed the performance requirements of the following standards,\n\nDenison Hydraulics HF-0 Eaton M-2950-S & Eaton I-286-S3\nDIN 51524 Part II Class HLP\nCincinnati Machine P-68,P-69 & P-70\n

Stiff, non melting silicone grease compound for use as a valve lubricant and sealantApplications\n\nLubricant for O-rings, packings, rubbers, gaskets, miniature bearing seals to provide resistance to water, chemicals, oxidation and provide thermal stability\nLubrication of pneumatic control valves, fire extinguishers and water softener valves\nSealant and lubricant for glass joints and stopcocks in normal as well as high vacuum systems\nLubricant for pressure lubricated plug valves, flow meter bearings, ceramic plug cocks\nSealant for vacuum and pressure systems\nSealant between synthetic rubber or plastic parts to prevent them from sticking to in vacuum or pressure systems\nChemical barrier and resistant coating for chemical processing equipment\nDamping media for dash pots in electrical and electronic equipment\nAssembly agent for holding rubbers and other parts due to its highly tacky nature\nAll ingredients comply with regulations for food grade materials\n\nBenefits\n\nWide service temperature range from -40°C to + 200°C Very good oxidation resistance\nCompletely resistant to water, steam, humidity and corrosives\nLow Vapor pressure and low volatility\nCompatible with plastics, rubbers, elastomers, and other gasketing and O-ring seal materials\nPrevents age hardening, stress cracking and maintains resilience of plastics\nNon gumming, non melting and non toxic\nProvides good lubricating and sealing properties for rubbers and plastics\nChemically inert and resistant to most chemicals, hot and cold water, vegetable and mineral oils, dilute acids and alkalis, glycerin, ethanol, methanol, butane, steam, natural gas, ethylene glycol, most organic and inorganic chemicals and aqueous solutions.\n\nMethods of Application Apply by means of hand, brush or putty knife. Can also be dispersed in solvents like mineral spirits, xylene or methyl ethyl ketone for thinning the consistency and making it easier to apply by brushing, dipping or spraying. Do not mix with other oils or grease.

Shelf Life : 24 Months from Date of Manufacture in Sealed Condition.

JETEX BRG-575 HTS GREASE is a low-noise, high-speed grease for plain and rolling bearings. It consists of synthetic oil and lithium soap along with additives for protection from corrosion and oxidation. It is highlyresistant to ageing and offer low internal friction. It reduces friction and wear; increases service life of the equipment and cuts down on lubrication costs by increasing relubrication intervals.Features \n\nExtremelysoft consistency\nHighlyoxidation stable\nWater-resistant & prevents corrosion\nLow-noise and low-friction grease\nGood corrosion protection\nResistant to oxidation and ageing\nVerygood low temperature performance\n\n

Fast evaporating, residue free, cleaner / degreaser for fast removal of contaminants from metal surfaces; free of chlorinated solventsJETEX HDG-86 is a non chlorinated, fast drying cleaner / degreaser for mechanical cleaning applications as a alternative for chlorinated solvents like CTC, 1,1,1 Trichloroethane. Safety standards from both, worker health as well as environmental, prohibit the use of chlorinated solvents like CTC or 1,1,1 TCE.JETEX HDG-86 rapidly penetrates through grease, oil, dirt, dust and other contaminants and cleans equipment fast. It has a pleasant citrus odor, fast evaporation rate and does not leave any residue. JETEX HDG-86 cleans metal surfaces effectively due its superior penetrating and wetting ability.It does not contain any CFC’s, chlorinated solvents or ozone depleting chemicals and is suitable for cleaning / degreasing of all metal surfaces and equipment only.ApplicationsFor heavy duty cleaning / degreasing applications of all mechanical equipment as brakes, chains, gears, bearings, clutches, generators, hand tools, molds, dies, slides, pumps, forklifts, valves, nuts & bolts, pipes, power tools. Safe for use on all metal surfaces, glass, most plastics and ceramics.Benefits Removes grease, oil, dirt, dust, sludge Non corrosive, non conductive & non staining Removes tar, adhesives and other tough contaminants Leaves no residue Safe on metals, most plastics, glass and ceramics Non chlorinated formulation Fast penetrating and superior wetting action 360° valve allows spraying in any position-even inverted Directions for Use (Bulk)Never use on energized equipment. Do not dilute with any other cleaning agent, water or mix with any solvent. Apply onto soiled surface and continue dipping / applying / spraying liberally until only solvent runs out clearly and contaminants have been washed off. To remove heavy carbon or oxides, use a brush. Allow solvents to dry off the components before reactivating. To enhance drying time, apply forced air or wipe dry with an absorbent cloth after applying. Use only when completely dry. Test on plastics prior to use for compatibility.Directions for Use (Aerosol)Never use on energized equipment. Spray using pin-point extension tube onto soiled surface and continue spraying liberally until only solvent runs out clearly and contaminants have been washed off. To remove heavy carbon or oxides, use a brush. Spray starting at the top of the surface and slowly working towards the bottom. Allow solvents to dry off the components before reactivating. To enhance drying time, apply forced air or wipe dry with an absorbent cloth after applying. Use only when completely dry. Test on plastics prior to use for compatibility.Caution: Contains flammable solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.GeneralUse in well ventilated areas. Avoid continuous breathing of Vapor and spray mist. In closed areas or areas with poor ventilation, use respiratory protection. For complete details on safety, short and long term exposure, refer to this product’s safety data sheet (SDS).DisposalAll used and unused product should be disposed of in accordance with state regulations.HandlingRead instructions on the container label of the product before use. The product safety data sheet (SDS) contains the relevant information regarding personal protective equipment, safe use, physical and health hazards.Limited WarrantyThe information and data contained in this sheet is accurate to the best of our knowledge or is obtained from sources, tests or experiences believed by us to be reliable and accurate. User is responsible for determining whether recommended product is fit for a particular purpose. All products should be tested for suitability on a particular application prior to actual use. We make no representations of any kind. Data offered without warranty.

Shelf Life : Bulk - 12 Months from Date of Manufacture in Sealed Condition Aerosol - 24 Months from Date of Manuf

Solid lubricant paste for effective running in, assembly, press fitting and anti seize applicationsBenefits\n\nExtremely wide service temperature range of -25°C to +450°C (up to +630°C in areas with restricted air access)\nLow coefficient of friction\nHigh pressure withstanding capacity\nLoad bearing capacity exceeds the yield point of most metals\nOffers protection from wear and friction\nEliminates metal-to-metal contact\nPrevents seizure, scoring, galling, fretting corrosion and stick slip\nMakes disassembly easier and non-destructive irrespective of operational period or conditions\nEconomical to use owing to its high surface coverage capacity\nAids running in and provides emergency lubrication during start ups\nPrevents cold welding and stick slip\nGood affinity for metal surfaces\n\nApplications\n\nAs a running-in, metal priming paste for all new or rebuilt mechanical equipment such as journal bearings, gear boxes, splines.\nAs a press-fitting lubricant to reduce press-fitting power required and prevent misalignment, seizure, wear, distortion especially under heavy load conditions.\nFor lubrication of all sliding metal surfaces to reducewear, friction and prevent cold-welding of surfaces such as for shafts, bushes, splines shafts, pumps,\nvalves, threaded spindles, toothed gears, worm gears and transmission gears, lead screws, machine tool guides, pumps, flanges, anti friction bearings.\nAs a metal working lubricant to prevent galling, seizure, welding and metal pick up on tools and dies in deep drawing, machining, punching, stamping, thread rolling,\ncold heading, waging and forging.\nAs a universal assembly paste to reduce tightening torque required; for enabling easy and non-destructive disassembly of components after long operational hours under operating and temperature variations.\nAs an antifriction and anti wear lubricant for heavily loaded surfaces under slow sliding speeds for preventing cold welding of sliding surfaces under heavy loads.\nAs a standard anti seize compound for all threaded connections during assembly stage for maintenance free dismantling.\n\nMethod of Application Clean the sliding surfaces and friction points. Apply this paste with a brush or cloth and rub intensively on the metal surface to form a thin uniform film. Do not use in excess as is customary with greases. Do not mix with other oils or grease.

JETEX EPS-10 Spindle Oils are premium quality, highly refined lubricating oils formulated for use in high-speed, lightly loaded bearings, running at speeds of 20,000 to 40,000 RPMs, found in textile spinning frames and in automated machine tools. JETEX EPS-10 Spindle Oils provide excellent oxidation stability, rust protection and resistance to deposit formation. Their low viscosities reduce oil thickness, lowering operating temperatures by reducing friction. The carefully balanced anti-wear chemistry contained in JETEX EPS-10 Spindle Oils helps extend equipment life.Applications \n \n textile industry where machine oil does not contact fabrics or oil staining is not an issue \n automatic machine tools and other applications where operating speeds are in excess of 10,000 rpm \n \n Features/Benefits \n \n excellent oxidation stability \n non-corrosiveness to metals \n excellent water separation characteristics \n excellent protection from rust and oxidation \n excellent anti-wear properties \n \n Approvals and Recommendations \n \n Cincinnati Lamb P-45 (JETEX EPS-10 Spindle Oil 22) \n Cincinnati Lamb P-62 (JETEX EPS-10 Spindle Oil 10) \n \n  

JETEX EC-424 grease is a specially formulated, highly conductive lubricant cum protective agent for maintenance free lubrication of electrical contacts and linkages in high and low voltage electrical transmission equipment. It does not harden even after long-term exposure to high temperatures and exhibits excellent high temperature oxidation resistance and protection to electrical contacts from weathering influences such as corrosion and moisture. It forms a wear reducing, heat dissipating lubricating film between surfaces to increase life of contacts and equipment.Benefits Highly conductive and suitable for transmission of electricity at high or low voltages Prevents corrosion and preserves contacts even at high temperatures or heat Withstands severe arcing Preserves contacts at high temperatures Permits minimum voltage drop across contacts Highly oxidation stable Very good conductor of heat and electricity Maintains a solid lubricating film over the surface and prevents premature wearing of contacts Increases life of contacts Applications Lubrication of electric powered contacts at high and low voltages. Electrical contacts and linkages in precision engineering and circuit breakers (up to 33kV). Contacts and equipment under corrosive atmospheres such as battery terminals, switches, sliding contacts, relays, mechanical controllers, interrupters, plug sockets, over load tap changers. As a heat sink media to facilitate conduction of heat and electricity. Method of ApplicationBy cloth or brush. Do not mix with any other oils or grease.

Shelf Life : 24 Months from Date of Manufacture in Sealed Condition.

JETEX EC-111 GREASE is a synthetic grease designed specifically for providing conductivity to electrical contacts. It provides superior lubrication and offers complete protection to electrical contacts from weathering influences such as corrosion, oxidation, and moisture penetration. This soft consistency grease prevents burning, oxidation, carbonation, arcing and erosion of contact surfaces. It is non-drying and forms an invisible film between bearing or sliding surfaces to reduce frictional wear and improve life of contacts. Based on synthetic fluids, this grease is free from any mineral hydrocarbon fluids that may cause carbonation or any migrating silicones and is safe to use on all surfaces.Benefits\n\nExtremely soft consistency\nWater-resistant & prevents corrosion\nReduces contact wear and improves conductivity\nIncreases life of equipment\nActs as an anti oxidant and anti corrosion sealant\nPrevents spark erosion and burning\nReduces cross contact seizing\nPreserves contacts even at high temperatures or heat\nHighly oxidation and chemically stable for long intervals of time\n\nApplications\n\nContacts in precision engineering.\nElectric contacts of all types to prevent spark erosion and burning.\nContacts and equipment under severe arcing conditions and corrosive atmospheres such as battery terminals, voltage regulators, sliding contacts, relays, rheostats, bus bars, mechanical controllers, interrupters, plug sockets, over load tap changers.\n\nMethod of ApplicationBy cloth or brush. Do not mix with any other oils or grease.

Shelf Life : 24 Months from Date of Manufacture in Sealed Condition.