Filter Assembly Dealers in Ashram Road, Ahmedabad (16 products available)

The initial operation of a membrane filter press is identical to that of its recessed chamber counterpart.   However once the filtration cycle is complete and final filtration pressure is achieved the feed into the filter press is stopped.   At this point the plates within the Filter Press can be inflated using either air or hydraulic pressure to exert a mechanical force on the filter cake retained in the chamber.   The effect of the squeeze is to physically compress the filter cake and force out additional moisture held within the cake giving a drier end result.   Membrane filter plates are used to   Reduce filter cake moisture content Reduce filtration cycle time Improve cake washing   This style of filter plate can be installed as   A full plate pack Alternately in conjunction with recessed companion plates as a more economical option.   Because of its simplicity and flexibility, the chamber Filter Press has been widely applied in clarification and dewatering applications. Membrane Filter Press technology is gaining increased acceptance because it reduces subsequent processing or disposal costs for filter cake. In many applications the membrane Filter Press significantly reduces residual moisture content, making this technology attractive for new plants and for upgrading existing facilities. In both cases the careful selection of plate and membrane materials is essential to the successful performance of the process.   Membrane Filter Press Plates have a chamber below the drainage surface that can be inflated. The common method used is water pressure, which is generated by pumping into the squeeze cavity to inflate the face of the plate against the filter cake. Membrane Plates are used to reduce the cake moisture content & shorten the filtration cycle time.   Mix Pack Membrane are the most common configuration (one recessed plate then one membrane plate alternate in the press plate pack). Membrane Plates usually operate at a feed pressure of up to 7 bar and squeeze pressure up to 15 bar. Special plates can be designed for higher feed & squeeze pressure.   Replaceable membranes can easily changeable. EPDM thermoplastic and other compounds are used for specific conditions. Plate filling problems are minimized and use of a rubber Membrane enables “empty-chamber” operation without damaging the plate, resulting a considerable reduction in incidents of plate failure. Even if the chamber is not completely filled, the filter cake is squeezed by the inflating filter lever and therefore perfectly dewatered.   During the initial phase of the filtration cycle, so-called “fill and filtration” the process is similar to the chamber Filter Press. After reaching a predefined pressure, usually around 3 - 7 bar, depending on the sludge characteristics, sludge feeding is stopped & the rubber membranes inflated, using either water or air as squeeze medium. The cake is hereby compressed and dewatered further. Then the squeeze medium is relieved & the cake discharged.

We are a well-known sintered bronze filter element manufacturer. Different types of sintered bronze filter element can be easily purchased under single roof named as ami enterprises. We produce very high quality sintered bronze filter element. For the filtration purpose of liquids & gases. It is made by powder metallurgical method. It is produce from spherical bronze metal powders of closely controlled particle size to give a rigid porous bronze structure of uniform pore dimension. technical data chemical composition (nominal) : cu - 89 % sn - 11% density : 5 - 6.5 gm/cc porosity by volume : 30 - 45 % coefficient of linear expansion : 18.3 x 10 6 / oc temperature suitable : in oxidizing gasses (air) up to 180 oc or in reducing gasses up to 400 oc application polymer filtration gasses filtration compressors pneumatic equipments mining equipments steam & gas turbine other application sound silencer flame cutter fluidization

Lead Time : As Per Requirement

Supply Ability : As Per Requirement

Port : Any Port In India

Brand Name : Filter Concept

Filter Concept Pvt. Ltd. is one of the leading Bag vessel assemblies exporters. Bag vessel assembly keeps the filter system on stream by reducing bag filter change time. Bag vessel assemblies are portable and light weight. Bag vessel assemblies advantages are High efficiency filtration, Dynamic large 'O'-ring seal and Knife edge sealing. Flow Rate Capacity:Up to 15000 lits /hr Per Unit & More Operation : Unfiltered fluid enters the housing and is distributed evenly around the filter bags. Filtration takes place from inside to outside. Solids are collected on the inside of filter bag for easy removal. The filtered fluid then exits through the outlet pipe.     Material Of Construction [MOC]-Bag Filter Housing O-ring - Buna-N / EPDM / Silicone Cap - Polypropylene Sump - Polypropylene Gauge - Brass (Optional) Vent Plug - Polypropylene Drain Plug - High density Polypropylene (Opt.) Ball Valve - PVC / Buna-N Seals (Optional) Basket - Polypropylene / SS 304 Gasket - Buna-N SIZES Bag filter system suitable for » Ø 4” x 10” Long Filter Bag » Ø 4” x 17” Long Filter Bag » Ø 6” x 20” Long Filter Bag Available End connections » 1” NPT Inline » 1.5” NPT Inline » 2” NPT Inline

Bag filter system is designed for optimum filtration performance. Its range provides filtration solution for a broad variety of fluid applications in the process industry.

Brand Name : GOPANI PRODUCT SYSTEMS

we offer washable filter cartridges. there is an obvious need of an effective reusable pre-filter in almost every filtration application where there is a need to control increasing cost of disposable type filter cartridges due to high contamination loads. these washable net filter cartridges effectively removes particle ranging from 5 micron to 100 micron, and useful as pre-filter for collection of gross contaminants. this cartridge reduces consumption of expensive disposable type filter cartridges when used as pre-filter and also serves as stand alone filter for a wide variety of application

Shape : Cylindrical

Application : Industrial

Length (inch) : 15-20 inch

Diameter : 3

Filter Medium Material : Polyester With PTFE

Operating Temperature(Degree celsius) : Up to 150 Degree C

Babul wood charcoal screened

PVC Bag Filter Housings are the best option and an alternative for Stainless steel housings. They are designed for high flow rate and high dirt holding capacity.PVC Housings are useful for filtering highly viscous fluids. TECHNICAL SPECIFICATIONS Material of Construction: - PVC Inlet and outlet: - 2” ANSI Flange Closure type: - Union closure and Nut-Bolt type Pressure withstanding capacity: - 60 psi (Maximum); Continuous: - 45 psi APPLICATIONS Oil Applications Paints Inks Sugar Syrup Polymers Chemicals Pharmaceuticals Lacquers

wite : golden

Silica Sand for Glass Industry Click to Zoom Silica Sand for Glass Industry We provide high purity silica sand for glass industry application with min. 99% SiO2 content and controlled moisture. Our special glass industry grade silica sand have below general specification. However we can make specialized graded silica sand as per our client’s requirement. Parameter Limit SiO2 99% Min Al2O3 ≤ 1.00 % Fe2O3 ≤ 0.15 % CaO + MgO ≤ 0.20 % Loss on Ignition (LOI) ≤ 0.50 %