Guru Corporation Prahlad Nagar, Ahmedabad, Gujarat

Country of Origin : India

Packaging Size : 50 Kg

Packaging Type : HDPE Bags

Usage/Application : Steel & Paint & Construction

Details Test results indicated that the concrete specimens containing 5%, 10 %, 15 %, 20% A-Sio2   replacement by weight for cement had the best compressive and flexural strength and the replacement of cement separately and together using a super plasticizing admixture could be utilized to improve the mechanical properties of the conventional concrete mixtures. Amorphous silica (a-SiO2) in fine-grained form possesses a high pozzolanic activity which makes it a valuable component of blended binders in concrete production. The origin of A-SiO2 applied in cement-based composites is very diverse. SiO2 in amorphous form is present in various amounts in quite a few supplementary cementing materials (SCMs) being used as partial replacement of Portland cement. In this work, the applicability of a commercially produced silica powder as a partial replacement of Portland cement in cement paste mix design is investigated. Portland cement CEM I 42.5R produced according to the EU standard is used as a reference binder.  silica is applied in dosages of 5 and 10, 15, 20 % by mass of cement. The water/binder ratio is kept constant in all the studied pastes. For the applied silica, specific surface area, density, loss on ignition, pozzolanic activity, chemical composition, and SiO2 amorphous phase content. For the developed pastes on the basis of cement-silica blended binder, basic physical properties as bulk density, matrix density, and total open porosity are accessed. Pore size distribution is determined using MIP analysis. Initial and final setting times of fresh mixtures are measured by the automatic Vicat apparatus. Effect of silica cement admixture on mechanical resistivity using compressive strength, bending strength, and dynamic Youngs modulus measurement. The obtained data gives evidence of the workability of paste mixtures with silica, whereas the setting process is accelerated. On the other hand, the reaction activity of silica with Portland cement minerals results in a slight decrease of porosity and improvement of mechanical resistivity of cement pastes containing a-SiO2. Nowadays, supplementary cementitious materials (SCMs) are widely used for preparing cement composites either in blended types of cement or added separately to the composite mix. The usage of active silica-rich materials represents an appropriate solution to partially replace Portland cement [1]. In addition, most of the SCMs are industrial by-products and their utilization in cement-based composites brings environmental and economic benefits. The admixture of different SCMs usually modifies the properties of cement composite to a certain degree both in the fresh and hardened states. These changes are influenced by different chemical and mineralogical composition, as well as different particle size characteristics which are connected with water requirement and also reactivity [2]. Active silica particles help to fill voids between particles of cement and other components because they are significantly smaller. This filler effect supports the formation of a denser microstructure because the gaps between the particles are minimized and bridged by hydration products.

Country of Origin : India

Packaging Type : Paper

Brand Name : Volsil

Packaging Size : 20 KG

Shelf Life : 2 Year

G-GROUT MF-8 Inception - G- GROUT MF-8 is highly fluid,single component, cementitious grout pre packed . G-GROUT MF-8 powder It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks,pores and voids. It has much finer particle size than other hydraulically setting materials. It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality. PurposeG- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes. ·MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with waterBenefits G-GROUT MF-8 can be injected with standard cement grouting equipment Compatible with most of the admixtures to accelerate / retard the setting time Supports all portions of structures Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen Non-toxic, Non-Hazards Eco friendly & Cost Effective. Technical Specification Properties : G-Grout Value Consistency : Dry Powder Colour : Grey Methods of Uses Pre-processThe substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed. MixingMF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes. Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.PackagingG-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.StorageG-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25°C, protected from heat, frost and direct sunlight. SAFETY INFORMATION Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice

Country of Origin : India

Packaging Type : PP Bags

Packaging Size : 25KG

Form : Powder

Packaging Type : Packet,HDPE Bag

Packaging Size : 25 Kg

Country of Origin : India

Form : Powdered

Brand Name : Brand

Brand Name : Guru

Country of Origin : Made in India

Application : Construction

Thickness : Dry

Grade : High

Packaging Size : 50 Kg

Packaging Type : Packet, HDPE Bag

Brand Name : Guru

Country of Origin : Made in India

Production Capacity : 500 MT

Country of Origin : India

Brand Name : GG

Usage/Application : Industrial

Packaging Type : Bag, HDPE

Packaging Size : 50 Kg

Grade : Industrial Grade

Packaging Size : 25 Kg

Packaging Type : Packet, HDPE Bag

Application : Foundry

Brand Name : GG+

Production Capacity : 300 MT

Material : Powder

Application : Cast Steel, Casting Iron, Foundry

Feature : Better Slag Exfoliation, Excellent Removal, Non-corrosive

Packaging Type : Bag, Can

Packaging Size : 10-20kg, 20-30kg

Country of Origin : India

Country of Origin : India

Packaging Size : 22 Kg

Packaging Type : PP Bag

Grade : 0.63 in to 0.02 in diameter

Grade : Snow White

Application : Ceramic

State : Powder

Packaging Size : 25 Kg

Packaging Type : HDPE Bag

Country of Origin : Made in India

Grade : Industrial

Brand Name : Guru

Country of Origin : Made in India

Size : 10-200mm

Country of Origin : India

Grade : A+

Material : Quartzite

Packaging Size : 50 Kg

State : Crystal

Packaging Type : Hdpe Bags, Hdpe Bag with Inner Lining, Pp Bag

Grain Size : 0-10 Mm

Temperature : High

Packaging Size : 50 Kg

Brand Name : Guru

Country of Origin : Made in India

PLEASE CONTACT ON : +919909987033 We would like to take an opportunity and introduce our company (GURU CORPORATION) that is involved in manufacturing and exporting of Concrete Additives products like Micro Silica Fume Brand G-Chem, Cement Grout Brand G-Grout MF8, Ultrafine Brand - G-Fine from Ahmedabad, Gujarat, India. For More Details you can visit our website : CONTACT ON : +919909987033 GURU INFRACHEM AHMEDABAD- GUJARAT - INDIA

Country of Origin : India

Brand Name : G-CHEM

Packaging Size : 25 Kg

Mesh Size : 200 Mesh

Purity : 95%

Usage/Application : Construction Industry,Industrial Production

Feature : Safe Packaging,Premium Quality,Perfect Finish,Leakage Proof

Material : POWDER

Grade : 92

Manufacturer & Importer of Micro Silica    Guru Infrachem Guru Corporation

Material : Powder

Brand Name : G-Chem

G-GROUT MF-8 Inception - G- GROUT MF-8 is highly fluid,single component, cementitious grout pre packed . G-GROUT MF-8 powder It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks,pores and voids. It has much finer particle size than other hydraulically setting materials. It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality. PurposeG- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes. ·MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with waterBenefits G-GROUT MF-8 can be injected with standard cement grouting equipment Compatible with most of the admixtures to accelerate / retard the setting time Supports all portions of structures Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen Non-toxic, Non-Hazards Eco friendly & Cost Effective. Technical Specification Properties : G-Grout Value Consistency : Dry Powder Colour : Grey Methods of Uses Pre-processThe substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed. MixingMF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes. Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.PackagingG-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.StorageG-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25°C, protected from heat, frost and direct sunlight. SAFETY INFORMATION Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice

Country of Origin : India

Packaging Size : 25 Kg

Packaging Type : PP Bag

G-GROUT MF-8 Inception - G- GROUT MF-8 is highly fluid,single component, cementitious grout pre packed . G-GROUT MF-8 powder It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks,pores and voids. It has much finer particle size than other hydraulically setting materials. It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality. PurposeG- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes. ·MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with waterBenefits G-GROUT MF-8 can be injected with standard cement grouting equipment Compatible with most of the admixtures to accelerate / retard the setting time Supports all portions of structures Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen Non-toxic, Non-Hazards Eco friendly & Cost Effective. Technical Specification Properties : G-Grout Value Consistency : Dry Powder Colour : Grey Methods of Uses Pre-processThe substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed. MixingMF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes. Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.PackagingG-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.StorageG-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25°C, protected from heat, frost and direct sunlight. SAFETY INFORMATION Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice

Country of Origin : India

Packaging Type : 25 Kg

Packaging Size : 25KG

Number Of Flower : Powder

Brand Name : GURU

G-GROUT MF-8 Inception - G- GROUT MF-8 is highly fluid,single component, cementitious grout pre packed . G-GROUT MF-8 powder It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks,pores and voids. It has much finer particle size than other hydraulically setting materials. It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality. PurposeG- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes. ·MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with waterBenefits G-GROUT MF-8 can be injected with standard cement grouting equipment Compatible with most of the admixtures to accelerate / retard the setting time Supports all portions of structures Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen Non-toxic, Non-Hazards Eco friendly & Cost Effective. Technical Specification Properties : G-Grout Value Consistency : Dry Powder Colour : Grey Methods of Uses Pre-processThe substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed. MixingMF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes. Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.PackagingG-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.StorageG-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25°C, protected from heat, frost and direct sunlight. SAFETY INFORMATION Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice

Country of Origin : India

Brand Name : G- GROUT MF8

Packaging Size : 25 Kg

Country of Origin : India

Packaging Type : HDPE Bag

Packaging Size : 25 Kg

Grade : High

Brand Name : Guru

Country of Origin : India

Brand Name : GURUKA

Packaging Size : 25 Kg

Packaging Type : Packet, HDPE Bag

Grade : Silica / Cromite / Zircon

Country of Origin : India

Packaging Size : 25 Kg

Test results indicated that the concrete specimens containing 5%, 10 %, 15 %, 20% A-Sio2   replacement by weight for cement had the best compressive and flexural strength and the replacement of cement separately and together using a super plasticizing admixture could be utilized to improve the mechanical properties of the conventional concrete mixtures.Amorphous silica (a-SiO2) in fine-grained form possesses a high pozzolanic activity which makes it a valuable component of blended binders in concrete production. The origin of A-SiO2 applied in cement-based composites is very diverse. SiO2 in amorphous form is present in various amounts in quite a few supplementary cementing materials (SCMs) being used as partial replacement of Portland cement. In this work, the applicability of a commercially produced silica powder as a partial replacement of Portland cement in cement paste mix design is investigated. Portland cement CEM I 42.5R produced according to the EU standard is used as a reference binder.  silica is applied in dosages of 5 and 10, 15, 20 % by mass of cement. The water/binder ratio is kept constant in all the studied pastes. For the applied silica, specific surface area, density, loss on ignition, pozzolanic activity, chemical composition, and SiO2 amorphous phase content. For the developed pastes on the basis of cement-silica blended binder, basic physical properties as bulk density, matrix density, and total open porosity are accessed. Pore size distribution is determined using MIP analysis. Initial and final setting times of fresh mixtures are measured by the automatic Vicat apparatus. Effect of silica cement admixture on mechanical resistivity using compressive strength, bending strength, and dynamic Young''''s modulus measurement. The obtained data gives evidence of the workability of paste mixtures with silica, whereas the setting process is accelerated. On the other hand, the reaction activity of silica with Portland cement minerals results in a slight decrease of porosity and improvement of mechanical resistivity of cement pastes containing a-SiO2.Nowadays, supplementary cementitious materials (SCMs) are widely used for preparing cement composites either in blended types of cement or added separately to the composite mix. The usage of active silica-rich materials represents an appropriate solution to partially replace Portland cement [1]. In addition, most of the SCMs are industrial by-products and their utilization in cement-based composites brings environmental and economic benefits. The admixture of different SCMs usually modifies the properties of cement composite to a certain degree both in the fresh and hardened states. These changes are influenced by different chemical and mineralogical composition, as well as different particle size characteristics which are connected with water requirement and also reactivity [2]. Active silica particles help to fill voids between particles of cement and other components because they are significantly smaller. This filler effect supports the formation of a denser microstructure because the gaps between the particles are minimized and bridged by hydration products.

Country of Origin : India

Brand Name : Volsil

Packaging Type : Paper Bag

Shelf Life : 2 Year

Technical Specifications SiO2 - Silica : >90% Color : Grey

Country of Origin : India

Material : Powder

Packaging Size : 25 Kg

Packaging Type : PP Bags