Located in Ahmedabad (Gujarat, India), Arpan Industries is a dependable water repellent coatings manufacturer in Ahmedabad. Our industrial waterproofing chemicals are of high-quality and that is why these are in high demand by renowned industries and factories. It has a purity percentage of 92% and is apt for using at industrial operations. The chemicals are delivered in high-quality packages that protect them from getting degraded. These chemicals are delivered in the packaging quantity of 20ltr. Our Water Repellent Coatings are widely appreciated because of their quality. So, if you are looking for a trustworthy water repellent coatings supplier in India then get in touch with us.
One pack, flexible, cement-based waterproofing with carbonation inhibiting properties. It adheres to all types of surface which provides a solution to leakage, seepage or ingress of water moisture in concrete by sealing capillaries and shrinkage cracks in both positive and negative side of the structure.Very Flexible, Vapour perme ability,dose not age,with stand high and low temperature can be used on all type of substrates
SpecialityWaterproof, Water Resistant, Solvent Resistant
Coating Thickness0.5-1mm
UsageWall Coating
Area of Use
Bridges
Industrial-Commercial Complex
Metal roofs & wall
Water Tanks
Exterior Walls
New and Existing concrete roofs & walls
Benifit U.V. resistant
High Durability
Crack bridging
Excellent adhesion
Flexible coating
Chemical resistance
Excellent waterproofing properties
Eco-friendly and easy to apply
1 litre of F SEAL WTM-720 covers from 35-40 sq. fits in 2 coats.
Dubond’s Hydro Shield is a solvent free silicone micro emulsion silicon and siloxanes. The ready to use, aqueous solution of Hydro shield serves as a high quality, general purpose water repellent for impregnating and priming mineral and even alkaline substrates.Damage to facade is always due to moisture, rain and surface water. Salt water damage occurs in porous building materials, only when moisture is present. The sources of salivation are deicing salts, rising dampness and reaction between the binder used in facade materials and paints. In addition to that, building materials have an inherent salt content. The moisture transports this salts to the surface of the substrate where it crystallization out. Salts are not only deposits on the surface but it cause the hydration and crystallization pressure. This builts up finally led to embrittlement and crumbling away of the surface. Acid rain i.e. sulphuric acid is by product in the form of sulphur dioxide by burning of industrial fuels, bound to particle of dust and droplets of water, is the primary cause for corrosion. Sulphuric acid reacts with the carbonates, the binder in mortars, lime washes, concrete, stones etc.Attack by moss and micro-organisms such as fungi and algae which are consequence of protected wetting of facade surfaces. The above mentioned facade damages can be diminished by impregnation with water repellant agents. The main aim of this is to form “hydrophobic” or dry zone on surface. The dry zone are not ideal for biotopes mosses, fungi, algae. The silicon molecules of Hydro shield do not clog the pores and so the surface retains its permeability to water vapour and “breathes”. Therefore treated buildings do not suffer from condensation damage. Buildings treated with Hydro shield may absorb very little water and can release it again readily in dryer conditionsAreas of Application
Hydro shield is recommended for a “Hydrophobisation” (water repellency) of facades . It is used as a general purpose water repellent for absorbent, mineral and even alkaline substrates, such as natural stone, brick concrete and sand lime brick, as well as for mineral paints and stuccos. HYDRO SHIELD is also suitable as a primer for dispersion based paints and stuccos, silicone resin paints and stuccos, concrete coatings, and as a water repellent for the in-plant treatment of lightweight aggregates and clay building materials, aerated concrete, sand-lime brick, fiber reinforced concrete and mineral fiber materials.Features & Benefits
Solvent free silicone concentrate. Ready to use.
Easily applicable by brush, spray or roller
Impermeable. Prevents penetration of water and moisture through the surface.
It aids in retaining the heat insulation properties of the wall because loss of heat through the wet brick is 1 ½ times greater than when it is dry.
It protects the surface from attack of salty and acidified atmosphere It prevents from formation of efflorescence.
It prevents the surface damage from water and frost attack. “Microporous”. Allows the substrate to breathe (good water permeability). Prevents the growth of microorganisms such as fungi and algae.
Their low viscosity and surface tension enable them to penetrate deeply in the material Excellent resistance to UV rays and weathering conditions.
It performs well in a temperature ranging from -20˚C to 50˚C It performs well on alkaline substrates
Application
Visible cracks must be sealed by Du Flex PS 600, polysulphide, or polyurethane sealant and primer . This sealants are not attacked by the repellent Hydro shield. Brush application is the simplest method Flat brushes or rollers can be used for application, while solution is applied, as the success or failure of such treatment depends on this factor.
Surface penetration is most important step before application to get best results and avoid failure The surface must be free from any loose materials, crumbling powdery encrusted walls,
fungus, moss, oil, grease and mould release agents. Clean the surface using scrappers and wire brushes
Then clean the walls with high pressure water, wait for 2 days for the surface to dry The walls must be dry before the application
Use of acidic and alkaline chemicals, detergents, cationic surfactants should be avoided It is advisable to wait for 28 days for curing the fresh masonary / new concrete
CoverageHYDRO SHIELD covers approx. 50-55 sq.ft / liter. Minimum 2 coats are recommended.Packing1ltr, 5 ltr, 10 ltr, & 20 ltr containerShelf Life & StorageHYDRO SHIELD has a shelf life of at least 12 months, if stores in tightly closed original containers between 0˚C and 30˚C the containers must be protected against direct sunlight. The “Best use before end” date of each lot is shown on the product label.Health & SafetyAvoid contact with skin and eyes, Incase of contact with eyes or skin, wash thoroughly with plenty of water and contact doctor.
Post Free Ad
