Water Purifiers Dealers in Naroda, Ahmedabad

Raj Group is engaged in the manufacturing of Rain Water Harvesting Filters of best quality. There are various ranges and sizes of this filter which are manufactured by the company. For filtering the rain water before its flows down through the pipe use of the Rain Water Harvesting Filters is made. Superior quality raw materials are sourced from the trusted vendors of the industry to avoid any type of quality issues. Application of the filter can be seen in both residential and commercial properties. The product is designed in a simple manner and that what makes it easy to install and popular in the market. The product is cost effective and can be installed on any pipe inlet and outlet fixture or fittings. Latest technology is used in the manufacturing of the filter under the supervision of the professional experts in order to avoid any product issue. Installation of Raintap Filter In a building, rainwater is normally allowed to flow down from the roof through pipes. These pipes may be of PVC, asbestos cement, cast iron, galvanized iron etc. However, PVC is commonly used in the present times. They are cost effective and convenient for installation. Raintap Filter can be installed to any of the above pipes with suitable inlet and outlet fixture/fittings. Installation of filter to down water PVC pipe The down water pipes are placed vertical on the walls. These pipes receive water from the rooftop through 90° bend or elbow attached to them at the top. The other end of the pipe is left for the water to flow down or attached with a 45° elbow or a bend to facilitate the water to flow away from the building. RAINTAP FILTER is installed at the bottom end of the down water pipe. The pipe running down on the wall need to be fitted with a 90° elbow or a bend connected to the inlet (rainwater inlet) of the Raintap Filter . The connection from the down water pipes to the inlet is through the 110 mm (4") elbow and a connecting pipe. The filter so installed must have a gap of minimum 3 inches from the floor and 1 inch from the wall. This will facilitate easy operation of the flush cap whenever require and make the cleaning of the filter element easier while retrieving it from its socket. Raintap Filter has an outlet (filtered water outflow) through 110mm Tee joint. This Tee joint along with the filter cartridge can be turned in any direction (360°) in its place. This will facilitate positioning of the filter outlet in any direction convenient for installation in the field. This facility is provided in the filter to add flexibility in connecting the outlet of the filter in the required direction. The out flow of the filter through this outlet is connected to the storage tank. The filter so installed need to be anchored to the wall by using pipe clamps/saddles at minimum 3 locations. The Locations suggested are : The inlet of rain water The adopter of the flash value The vertical body of the filter To grow the filter on the ground, two masonry supports are recommended to be constructed using bricks below the filter. Make sure the bricks support is not below the flush cap (the flush cap need to be opened time and again). With three clamps holding filter on the wall and two masonry supports from the bottom, the filter is rigidly fixed on the ground and wall. Filter Element Filter element is made of plastic net and mesh to effectively filter rainwater from the roof of a building. A cap-holder facilitates installation of the filter element inside the filter body and also positions the filter element at appropriate height inside the filter body. While removing the filter element from the filter, gently pull the cap-holder with its handle vertically upwards. Make sure the entire length of the filter element is pulled out of the filter before tilting. While installing the filter element back in to its position, make sure the mesh role enters the barrel without any crinkle. Gently push the filter element downwards up till the cap-holder suits and positions itself on the vertical column of the filter. The vent hole provide on the cap-holder of the filter element has to face away from the wall. This wall facilitates flow of water from the wall in case the filter is clogged. Important RAINTAP FILTER must be installed vertically only. These FILTER 110mm can handle rain water from a maximum of 1000 sq. ft. of roof area respectively .(1000mm annual rainfall) How Raintap Filter Works ? The "RAINTAP FILTER" has three components (rainwater receptor, flush valve and filter element). Rainwater receptor is where the rainwater is allowed to flow from down pipes into the filter and a flush valve is provide to flush the first flow of the rainwater along with leaves, dust etc. water received in the receptor flows upwards against gravity through a filter element to filter must of the floating element and allow water to stabilize in this filtration zone. Rainwater passing through this filter element is relatively cleaner and flows out through an outlet, which can be led to storage device. Filter element is mounted on a vertical stabilizer barrel with a friction fit. Filter element need to be cleaned periodically during the rainy season to remove the impurities trapped and thereby keep the filtration system clean .In the event where filter is not clean and the filter element is getting clogged, "Raintap Filter" has a safety feature built into it. The water pressure pushes out the clogged filter element from the stabilizer barrel and allows the water to flow out freely. This safety feature will avoid flooding of the rooftop because of the closed feature. The first indication of the filter getting closed is rainwater flowing out of a vent hole provided on the top of the filter element. Maintenance of Filter Flush of the first rainwater by opening the flush valve on the filter for few minutes , close the flush valve after all the dirt on the roof is flushed out and when cleaner water starts flowing. When the rain stops , flush the filter and remove the filter cartridge gently from its placed and wash its thoroughly under a running tap by gently tapping the filter. Element with a stick on all sides. The dirt sticking in the filter element get released and washes off. Replace the clean filter element back to its place by gently inserting it in the vertical barrel .Take care not to press it too hard at the end. If pressed too hard, filter element gets locked inside the barrel and may require for subsequent cleaning and also may not POPUP when the filter is clogged or chocked. Allow the filtered water to get stored in tank for future use

With the valuable assistance of a skilled team of professionals, we are offering an extensive range of high quality PITEX RO Water Purifier. We have a team of highly skilled and experience procurements agents that source only quality oriented products from the vendor’s end. We ensure our customers that all our products are precisely tested against various quality parameters at our in house testing unit. Highly used in various industrial, commercial and residential places, these are offended at industry competent prices. Features:  High performance Optimum functionality Resistant against corrosion Product Features: 75 GPD high pressure pump of BNQS N.F.S. Approved, leak proof connectors, fittings and tubes N.F.S. approved, non-toxic filter housing made up of food grade polymers Fully automatic system with auto ON/OFF facility High purifying capacity of CSM membrane which produces 12 liter water per hour. Purifies impure water to sweet pure drinking water Removes bacteria and virus Availability of water as per requirement, even in absence of electricity Low cost of maintenance and consumables Different stages of treating water: Stage 1 – 5-Micron Sediment Filter: With five micron rating, it is effective in removing dirt, rust and sand particles Stage 2 – 5-Micron Inline Sediment Filter: With five micron rating, it is effective in removing dirt, rust and sand particles Stage 3 – Granular Activated Pre Inline Carbon Filter: It takes out 99% of the chlorine and organic chemicals. It provides enhanced reduction of taste, odor, and color Stage 4 – Reverse Osmosis Membrane: A thin film composite high quality Aquaa care membrane processes 75 gallons water per day. It removes the hard water contaminants that may be present in water, like – lead, cooper, barium, chromium, mercury, sodium, cadmium, fluoride, nitrite and selenium. It also removes Bacteria and Virus from water Stage 5 – Post Carbon Inline Filter: It removes objectionable tastes and odors to enhance the quality of drinking water Stage 6 – Ultra Violet Tube: It removes Bacteria & Virus through ultra violet rays

Activated Carbon Filters, Water Treatment Plant, Water Treatment Plant

Commercial Water Purifier, RO Cabinet, Filter Housing, Inline Filte

Reverse Osmosis System, Induction Cooke

Best Quality RO System, Pressure Gauge, RO Water Plants, Insulation Shee

Water Purifier, BIOME MAGNETIC SINGLE BED MATTRESS WITH PILLO

Reverse Osmosis Syste

Water Purifiers, Domestic RO Systems, RO Commercial System

Water Purifier

Domestic Reverse Osmosis Systems, International Reverse Osmosis System

Pre Carbon Filter, Float Valv

Reverse Osmosis Water Purifier, Refrigerator Stand, Washing Machine Spare

Water Filter, Water Pumps, Fire Fighting Pum

Water Purifier Dealers, Vacuum Cleaner Wet Industria

RO System, Sewage Treatment Plant, Ultra Filtration Syste

Water Purifiers, Water Treatment Plants, Water Treatment System

Reverse Osmosis Water Treatment System, Ultra Filtration Syste

Water Purifier

Water Filter, Nani Trap, Fancy Long Plug, SS Waste Coupling, D Join

Water Purifiers, Water Purification Systems, Reverse Osmosis Plant

Water Filter, Chemical Purifier Eqiupment, Chemical Tank, Pharma Eqiupmen