Hand Tool Dealers in Ambala

We manufacture Chemistry Lab Equipment which is highly inflammable and satisfactorily pass every test for standard check. We offer a wide range of chemistry laboratory equipment which is used for various purposes in chemistry laboratory. Our best in quality products are capable of withstanding with the extremely severe conditions and for this they are pre-examined before delivery.

We offer lab tools kit. A nice assortment of most commonly used lab tools, available as one convenient set. Contains one each of following: test tube brush, spatula, crucible tongs, test tube clamp, lab scoop, forceps.

NAUGRALABS LABORATORY PRODUCT NAME: CRIMP TESTER FOR TESTING LAB NaugraLabs Laboratory Product Code: NLE-Export-390005 Description and Specification for Lab Tenders Crimp Tester For Testing Lab Workshop. Crimp Tester - For Testing Lab The crimp in a yarn is defined as the mean difference between the actual length of any yarn and its apparent length in the fabric after weaving. It is usually expressed as a percentage of the apparent length of the yarn in the fabric.   Determination of the crimp of yarn is carried out by marking a known length on the fabric, removing the marked yarn in such a manner that it does not loose its twist, holding it between two grips at the marked points, and slowly extending it till it is subjected to a specified straightening tension. The increase in length of the yarn is determined and expressed as a percentage of marked length to obtain the value of crimp.   The Crimp Tester is designed to determine the crimp of yarns taken out of fabrics. One end of the yarn is held in a pivoted loading grip on which the desired tension load is applied by means of a sliding weight acting on a lever arm, while the other end is held in a movable grip which is mounted on a screw and can move along the direction of the yarn, stretching it in the process. The distance moved through by this grip gives the extension of the yarn, and can be measured on a scale fixed by the side of the grip assembly civil lab equipments manufacturers

Made of special grade stainless steel. The jaws are hardened to provide better life to pliers. Available in different shapes. Available in plastic sleeve on handles to provide better grip.

Plated metal cone with hinged cutter blade set in slot and metal handle. Borer restored to circular shape by cone, edge cut to correct angle by depressing blade using thumb pressure. For borer dia. 4-27mm

We offer a wide assortment of Hexa Keys to customers. They are made from high-grade raw material with the aid of latest technology. Hexa Keys are offered in various specifications as per the requirements of clients. Hexa Keys are high on performance with easy maintenance and handling. They can be availed at industry leading prices.

Laboratory Vane Shear : The equipment consists of a torque applicator assembly mounted on a base. A gear wheel, which is marked in degrees, holds a torque ring and is geared to a crank. The torque ring is a split ring and deforms as torque is applied and the deformation is indicated by a dial guage. A calibration Chart to convert dial gauge readings to torque force in kg.cm. is supplied. A pointer is provided for registering the rotation of the vane. A detachbale stand is provided to anchor the instrument. An attachment to security hold the string of rods is provided. The equipment comprises of the following: Torque applicator assembly capacity 2000Kg. cm. with split proving ring and dial gauge 0.002mm X 5mm complete with stand. Vane (with vane rod) 37.5mm dia X 75mm high 1 No. Vane (with vane rod) 50mm dia X 100mm high 1 No. Torque rod (Square Cross section) 0.6mtr. Long 1 No. Rods, quicks coupling type, 1mtr. long 25 Nos. Rods, quicks coupling type, 1/2mtr. long 10 Nos. Dummy rod, corresponding to 37.5mm dia vane 1 No. Dummy rod, corresponding to 50mm dia vane 1 No. 

Our company offers a broad range of superior quality Limited Motion Knee Brace to match up with the demands of our respected clients. These knee brace helps in offering range of motionand flexion or extension locking in 10-degree increments. It also consists of unique locking system along with lid for protection. Our range of product is highly recommended for controlling mobilisation after Meniscus tears, ligament tears (especially ACL & PCL) and dislocations.

Pipe surge & water hammer are two related but independent phenomena which arise when fluid flowing in a pipe is accelerated or decelerated. The associated pressure transients can be damaging to pipe work or components and systems must be designed to avoid or withstand them. The equipment designed clearly demonstrates the different effects resulting from gradual or instantaneous changes in fluid velocity (created by slow and fast valve closure). Effect of initial fluid velocity can also be investigated. Pipe surge resulting from a gradual change in fluid velocity is clearly seen as fluctuating changes in head in a surge shaft. Water hammer resulting from a rapid change in fluid velocity is clearly seen as large changes in pressure monitored using a pair of transducers and indicated using an oscilloscope. The equipment comprises two SS pipes connected to a constant head tank. A service module provides the water supply to the head tank and also incorporates a volumetric tank for flow rate measurement, sump tank, circulating pump and flow control valve. Water enters the two test pipes via the constant head tank and discharges into the volumetric tank. A dump valve in the volumetric tank returns the water to the sump tank. The pipe surge test section incorporates a clear acrylic surge shaft to enable visualisation of its oscillatory characteristics to be demonstrated. A metric scale on the shaft permits the height of the oscillations to be measured. The test pipe terminates with a lever operated gate valve and separate flow control valve. The water hammer test section uses a unique fast acting valve specifically designed. Pressure transducers mounted at the fast acting valve itself and at a point along the test pipe provide analogue outputs which are fed into a signal conditioning module. The corresponding output voltage from the signal conditioning module can then be fed into a dual trace oscilloscope. Output is available from the oscilloscope. This allows the stored display to be transferred onto a suitable printer to provide a hard copy of the transient.

We take pleasure in introducing ourselves as one of the leading manufacturers and Exporter of Laboratory Equipments/Instruments, Glassware's & Chemicals for Schools, Colleges, Medical Colleges Medical Hospitals, Research Departments, Universities and Industries , Medical Products, Surgical Rubber products, Surgical Instruments, Hospital Equipments, Educational Science Equipments, Laboratory Glassware, Hospital Furniture, Operation Theater Equipments & Lighting, Surgical Instruments, Beauty and Health Care Product, Veterinary Items, Pharmaceutical Machinery. Our company is fully managed by a team of highly qualified personnel with our three decades of experience and active involvements in foreign business. We already exported our products so Singapore, UK, Malaysia, Sri Lanka, Bangladesh, Nepal, Kuwait, Saudi Arabia, Jordan, France, Germany, Canada and U.S.A. to the complete satisfaction of our clients and have every hope that with your kind co-operation shall certainly be able to enlarge our field of activities to our mutual benefit We are best suitable for following Sectors, Industries: Pharmaceutical Machinery Oil & Petroleum Medical Products Construction Equipment Food and Stuff Glass Bottles Industrial Supplies Biotechnology Technical Education Hand Tools Textile Solar System Herbal Products Beauty and Health Care Product Educational Instruments Testing Instruments Please forward us your Requirements / Enquiry / Tender list so that we may send you our best offer.

We have the complete range of HSS Hand Taps from 3mm to 50mm. We also stock all NON Standard sizes. RANGE 3mm to 50 mm ( Ready Stock ) : Can give up to 150mm

Ensure deep, clear, legible stamped impressions. Safeguards against mushrooming, chiping and splitting. Each punch is clearly marked with character designation and size. Made from high quality, heat-treated tool steel. Character faces combine high degree of hardness and toughness for exceptionally long life.