AIR Separator Dealers in Bangalore (5 products available)

For quite a few number of years now, we have been supplying the Cross Flow Separator that we manufacture in our very own factories under the guidance of our knowledgeable experts. This separator is made of top notch materials sourced from authentic vendors that account for the premium quality and performance it houses. We deal in bulk and medium sized orders primarily. The rates are affordable and delivery is punctual.   Details : In the modern TPI System, the separating surface area is increased vertically by the addition of a number of parallel plates mounted at an inclination. This not only affords a dramatic space saving but also facilitates very small separating diameter. The K-pack TPI consists of a plate pack constructed of closely spaced corrugated plates inclined at a 45° angle or more, depending on the application. Waste water flows through these plated either parallel to the corrugations in "Counter-current Flow" or at right angles to the corrugations in "Cross Flow". Under laminar flow conditions, the short distance between the inclined plates is now the only distance over which the pollutants have to rise or sink before they are intercepted and separated from the mother fluid. Imagine a rectangular tank with a surface A containing a liquid to a height H (see figure 1). Flow through the tank is homogeneous and the flow rate = Q The settling or rising velocity of a particle with diameter d is governed by Stoke's Law It follows that the tank surface A is inversely proportional to the square of diameter d of the smallest particle which will completely separate. An increase in the efficiency of a separator can, as a result, only be achieved by a considerable increase in the surface A, which leads to the installation of large tanks with large surface area A. The effectiveness of such large tanks is limited due to factors like : Turbulence and short-circuit currents. Variation in ambient temperature. Temperature gradients in the liquid. Surface wind load.   In the modern TPI System, the separating surface area is increased vertically by the addition of a number of parallel plates mounted at an inclination. This not only affords a dramatic space saving but also facilitates very small separating diameter. The K-pack TPI consists of a plate pack constructed of closely spaced corrugated plates inclined at a 45° angle or more, depending on the application. Waste water flows through these plated either parallel to the corrugations in "Counter-current Flow" or at right angles to the corrugations in "Cross Flow". Under laminar flow conditions, the short distance between the inclined plates is now the only distance over which the pollutants have to rise or sink before they are intercepted and separated from the mother fluid. Application : Mineral oil refineries, oil extraction, offshore platforms Tank storage farms Ballast water treatment Petrochemicals Galvanizing metal; mining industry Edible oil refining Foodstuffs industry Paper & pulp industry   The Cross flow separator system permits simultaneous separation of floating and settling materials like oils, fibres, sand etc.. But are also individually applicable as oil and solids separators. The raw water containing oil and/or suspended solids passes in horizontal direction between the closely spaced plates in the plate pack. Completely laminar flow conditions are established while the water flows across the plate pack from the inlet to the outlet side. Laminar and stable flow conditions are essential conditions for the effective gravity separation of the water, oil and/or the suspended contaminants.   Oil separation : In the course of passing through the plate pack from inlet to outlet, the oil floats upwards info the tops of the corrugations and rises up the incline of the plate to the surface of the separator, where it is removed by a skimmer. Solids Separation : The solids move towards the Bottoms of the corrugations and slide down the incline of ' the plate. From there the separated solids are collected in the sludge compartment of the separator to be partially dewatered and transported by a shaft less spiral conveyor and intermittently discharged through a blow-off valve (optional). Settled sludge cannot decontaminate the treated water. Oil and solids move in separate directions, but both perpendiculars to the flow of water, eliminating particle re-entrainment completely. All K-Pack separators are custom built with respect to the number of plates in the pack, the length of the plates, the distance between the plates and the plate incline. The number and the length of plates is determined as a function of the raw water flow rate to be processed in the separator. The distance between the plates is depending upon the concentration of solids / sludge in the raw water. The incline of the plates is set between 45 and 60 degrees depending upon the general nature of the Oil and/or sludge, (density, viscosity, concentration). The systems are fabricated in mild steel and other materials are available on request. The oil separators are standard with oil and skimpipe and 45 degree shaped compartment. The solids separators are optionally with a shaftless conveyor in the sludge compartment. In the corrugation tops a very high oil concentration is established. This is the ideal condition for oil coalescing to take place (formation of large oil droplets out of many small oil droplets). In the corrugation bottoms a high sludge concentration is established. This is the ideal condition for particle agglomeration to take place (formation of heavy particles from small and relatively light particles) Applications Mineral oil industry Edible oil industry Metal industry Ceramic industry Galvanic industry Mines Sand separation after washing of contaminated soil Food industry

We offer various filters such as Air Filter, Oil Filter, Fuel Filter, Lube Filter, Coolant Filter, Hydraulic Filter, High Pressure Filter, Hepa Filter, Air oil Separator, Filter Cart, Cabin Filter, Crank Case Ventilation, Steering Filter etc..  We are also authorised distributors for Mann+Hummel-Germany and Donaldson-USA.

Air separation column (cold box) consists of outer steel casing, Main heat exchangers, Bottom column, Top column, Condensor, Sub-coolers, Liquid nitrogen Tank. Expansion Valves, Drain & Analysis Valves, Niddle Valves Insulation material, Digital electronic temperature indicator & scanner, PT 100 sensors, Differential Pressure level Indicator. The expanded air leaving from the Expansion Engine & Air Expansion valve enters Air Separation Unit. The rich liquid containing Oxygen & Nitrogen is collected in Lower column having more than 40% O². The rich liquid from the lower column is taken to the upper column through RL Expansion Valve. The Poor Liquid (PL) collected on the bottom cone of Condensor is taken to upper column through PL Expansion Valves in this process pressure is dropped 4.5 kg/Cm² to 0.5kg/Cm² g in upper column . The Nitrogen being more volatile come out and oxygen getting condensed and collected in condenser from where it is pumped by LO²/LIN Pump in to cylinders. Temperature Scanner Liquid Level Gauge RTD Sensor Pressure Gauges Expansion valves Needle Valves. Drain & Analysis's Valve. Perlite Powder Top Column safety Valves --(0.65 Kg/Cm²) Bottom Column safety valve – (6.5 kg/Cm² ) High Pressure Safety Valves – ( 165 Kg/Cm² )

We offer air separators. We sell replacement air separators. Our air separators are rated better than the oem part or equivalent. Replacement airoil separators for all oem manufacturers are available.

Stainless Steel Shock Absorbers, Gas Spring, Rotary Damper, Piab Conveyor