STP & ETP Equipments Dealers in Coimbatore

The Tube Type Oil Skimmer removes tramp Oil (hydraulic oil, Spindle oil, etc.) from Coolant tanks, CNC Machines, Part washer’s etc. Which removes oil from water in wide large tanks efficeintly.

Oil skimmers usually incur a low initial cost, install easily, offer rugged construction, reliable operation and minimal upkeep. Training personnel for operation, monitoring and routine maintenance is nil. Still, there are different types of skimmers, and each application requires some analysis to make the best selection. Also, the water collection system must be set up properly in order to get maximum performance from the skimmer. The six major skimmer configurations for industrial plants and service shops are belt, disk, drum, mop, tube and floating suction types. For all types, the oil or other hydrocarbon liquids must be floating on top of the water. For all but the floating suction type, a moving skimmer medium is pulled through or across the surface to attract the oil. This oil is then removed as the medium is pulled through wiper blades or scrapers by a motorized drive system. The skimmed product is discharged through collection trays and drain channels into an external container.

we are offering Air Treatment. Being the leader in the industry, we offer Air Treatment of fine quality. User can prefer wall mounting, vertical or in-line mounting for this unit and is highly appreciated for its uninterrupted performance and long lasting durability. They are available in different specifications to meet the requirements of the clients and are provided at the best rates in the industry. In addition to this, it is thoroughly checked on its various parameters before delivery. Features : Abrasion resistant Durable Affordable Specifications : Construction modular, compact Materials zama, NBR, technopolymer Ports G1/4 - G3/8 - G1/2 Mounting vertical, in-line or wall-mounting Operating temperature -5°C ÷ 50°C at 10 bar (with the dew point of the fluid lower than 2°C at the min. working temperature) Finish enamelled Flow determined at 6 bar inlet supply with P 1 bar (P 0,5 only for FRL). For more detail, Log on to www.systel.co.in

Electromagnetic flow meter is used to measure flow rates of conducting fluids. It is used to measure flow rates of slurries, corrosive and abrasive fluids. Electromagnetic flow meter is also used to measure bidirectional flows by reversing connections, which can be done automatically. advantages of electromagnetic flow meter these meters do not cause obstruction to flow and hence cause no pressure drop. For measurements, it does not matter whether the flow is laminar or turbulent. It gives accurate results. Its reliability is high, that is, it gives a standard performance for an elongated period. It can handle greasy materials and fluids containing suspended solids. The measurement is independent of viscosity, density, temperature and pressure. basic principle when a flowing conducting fluid is subjected to a transverse magnetic field, the flowing conducting fluid cuts the magnetic field and causes a voltage to be induced. This induced voltage is proportional to the fluid velocity, that is, flow rate. construction the main parts of this instrument are as follows a conducting fluid is flowing through a non-magnetic and non-conducting pipe, whose flow rate is to be measured. Two electrodes are attached in opposite sides of pipe carrying the conducting fluid. These electrodes are in contact with the flowing conducting fluid.the pipe is surrounded by an electromagnet, which produces a magnetic field. Operation of a magnetic flow meter this magnetic flow meter is based on farady�s law of induced voltage which is given as follows : e = blv where, e = induced voltage(volts)b = flux density (gauss)l = length of conductor which is the diameter of the pipe (cm)v = average velocity of conductor (fluid) in cm/sec when the conducting fluid flows through the pipe that is subjected to a magnetic field, the conducting fluid cuts the magnetic field and due to this, a voltage is induced. As the magnetic field is constant, voltage obtained across the electrodes will be directly proportional t average fluid velocity and diameter (length) and hence becomes a measure of volume flow rate. limitations of magnetic flow meter the fluid whose flow rate is to be measured should satisfy certain conduction conditions.the fluid should be full in the pipe to get accurate results.air and gas bubbles in the fluid will cause errors.when certain fluids, the electrodes might get coated with scales and this will affect the output signal. However, this can be taken care of by cleaning the electrodes.in many cases, the output voltage is low and hence requires amplification.

Wastewater Treatment Equipment, Water Treatment Plan

Filter Press Cloth, Filter Press, Screw Pumps, Scrap Bundle Machin

Water Treatment Equipments, Dosing Pumps, FRP Softener Vessel

Oil Skimmer, Item Code - Sigma-10, Item Code - Beema-1

Water Treatment, Water Treatment Equipment, Solar Power Plan

Water Treatment, Water Treatment Plant, Sewer Cleaning Machin

Water Treatment Equipmen

Sewage Treatment Equipment, Fire Extinguisher Powder, Industrial RO Plan

Effluent Treatment Plant Equipment, Effluent Treatment Plan

Cement Mixer, Water Proofing Chemical Plant, High Speed Disperser

Water Flow Control LCD Meter, Hand Held Crop Senso

Water Treatment Equipmen

FRP Water Tanks, Full Height Turnstile Gate, Fixed Tube Sheet Heat Exchanger

Water Treatment Equipment, Solar Equipmen

We are one of the famous company, who are manufacturer of Sewage Treatment Equipments.

CNC Oil Skimmer, Thick SS Fire Proof Paints, Cassette Air Conditione

Water Treatment Equipmen