Backing Rings Dealers

We are offering ptfe back up rings in the global market that are manufactured using high quality ptfe material. Made with extreme precision, the ptfe back up rings are suitable for diverse industrial requirements such as for preventing seal extrusion under high pressure. The clients can avail the ptfe back up rings from us in varied sizes and diameters as per their requirements. available in solid typesspiral types

Serving the markets of Gurgaon haryana(India) and nearby area, we offer top-notch quality range. From catering to seasonal demand to a continuous one, we can do it, as we have an ultramodern storage facility, which is equipped with the latest inventory control and management system.

Our firm specializes in providing an exceptional assortment of Backing Ring. This pioneering assortment of rings is extensively demanded in different industries for meeting varied applications. To preserve industry defined quality norms, our complete assortment are fabricated using quality assured raw material and ultra-modern technology. Furthermore, offered assortment is observed properly by our quality auditors upon distinct parameters of quality.   Features:   Rust resistance Accurate dimension Enhanced durability

Back-up Rings are commonly used to protect seals from the effects of extrusion when pressurised adjacent to a housing gap. A wide range is available to suit all seals and grooves. Usual configurations are Spiral, Scarf cut, Uncut and Concave and materials range from Virgin Polytetrafluoroethylene (PTFE), through the range of filled grades, up to the high modulus grades of engineering thermoplastics. Back-up Rings can be used statically or dynamically, over a broad temperature and pressure range.  

Backup Rings prevent extrusion of O Rings In high pressures usually above 1500 PSI & compensate for loose fitting components.If only one backup ring is used, the O Ring should be placed between the pressure source & the backup ring.One backup ring should be used on each side of the O Ring in double acting assemblies if possible two backups should be used even in single acting assemblies.

Backup rings prevent extrusion "O" rings In high pressures usually above 1500 PSI & compensate for loose fitting components. One backup ring should be used on each side of the o ring in double acting assemblies if possible two backups should be used even in single acting assemblies. If only one backup ring is used, the "o rings should be placed between the pressure source & the backup ring. Contact us for more information on backup rings.

Quality being the major concern of our organization, we keep a stringent check on the production, packaging and delivery processes. Buy the best quality Back-up Ring at market leading prices, from us. We are amid the prominent Suppliers in the town. The offered Back Up Rings are available in various thicknesses ranging from 2mm to 30mm.

Hard rubber molded contoured Back-Ups are routinely produced in a 90 durometer Nitrile and Viton. This provides sufficient elasticity to permit stretching over the major diameter of a piston and then snapping back into the gland groove cut into the piston. 90 durometer has sufficient hardness to resist extrusion of the softer elastomeric O-Ring performing the actual sealing function against the high pressure liquid or gas. Back-up Rings are used in conjunction with O-rings and seals for both static and dynamic sealing applications. They prevent extrusion of the O-ring or seal when it is subjected to high pressure, and/or larger extrusion gaps. The back-up ring should be used on the opposite pressure side of the seal. For seals that are exposed to pressure from both sides, two back-up rings should be used, one on each side of the O-ring or seal.

  Back-up rings are normally supplied as a spiral of two turns. This enables the back-up ring to be opened with ease for fitting over a shaft, and ensures the 'O' ring is supported around its entire diameter. Single turn back-up rings can also be supplied, and these are usually endless to ensure good support. However, they can be scarf split if required, although we do not recommend this because extrusion can occur at the split.Smaller sizes of back-up rings are available only as a single turn. This is because spiral back-up rings need an inside diameter of 3mm or greater for machining purposes.     Materials   Our back-up rings are manufactured in either virgin PTFE, PEEK™ (from Victrex plc) or filled PTFE,  depending on the application.    Why use back-up rings?   Back-up rings are installed to prevent extrusion of the 'O' ring. Two back-up rings - one either side of the 'O' ring in its housing - are needed when the application is double acting.They are normally recommended for applications where:Pressure of the fluid medium exceeds 10MPa, or'O' rings of low strength elastomer are used, or Adverse mechanical conditions prevail.

TEFLON PTFE BACKUP RINGPTFE backup ring will help control O-ring extrusion in high pressure applications.

Backup Rings prevent extrusion of O Rings In high pressures usually above 1500 PSI & compensate for loose fitting components. If only one backup ring is used, the O Ring should be placed between the pressure source & the backup ring. One backup ring should be used on each side of the O Ring in double acting assemblies if possible two backups should be used even in single acting assemblies.

We offer different type of Back up rings which are used for holding arm of cable during termination. Back-up rings are used to hold the arm our of the cable during execution of the joint/ termination. Ideal offers different types of back-up rings i. E straight through, spilt type etc. In various sizes. Ideal also offer the same as per customer requirements and specifications.

Back-up Rings are used in conjunction with O-rings in both static and dynamic sealing applications, PTFE Back-up Rings are used to prevent the O-ring from entering the clearance gap, when high pressures are exerted on the O-ring, its soft rubber material can be forced into the clearance gap causing the O-ring to extrude, PTFE Back-up rings keep the O-ring material from flowing into the gap which will prevent premature failure. PTFE Back-up Rings are made in single turn "scarf cut", Spiral "multi-turn", and solid "uncut" Back-up Rings and PTFE products including Piston Rings, Washer, O-Ring, V-Seals, Balls, Valve Seats, Wipers, Wear Rings, Bearing , Rod Guide and custom parts in wide variety of polymer products in PTFE, PTFE Filled Compounds and many combinations of high-performance materials ideally suited for use in original equipment and industrial maintenance

Back up ring In high pressures usually above 1500 PSI & compensate for loose fitting components.One backup ring should be used on each side of the o ring in double acting assemblies if possible two backups should be used even in single acting assemblies. If only one backup ring is used, the "o rings should be placed between the pressure source & the backup ring.

We are leading supplier of huge range of back-up rings.

Back up Rings, Special Molded Seals, Chevron Packings, Metallic Oil Seal

Back up Ring, V Rings, Washers, Gaskets, Bellows, Crescent Rin