PCB Conformal Coating Dealers (21 products available)

• Packaging Size: 25 pcs
• Usage: Industrial
• Packaging Type: 300gms
• Grade Standard: Technical Grade
• Physical State: Aerosol
• Usage/Application: Industrial
• Country of Origin: Made in India
• Brand: WESAF

• Packaging Size: 400 ml & 35 lit.
• Brand Name: ISC
• Features: Fast drying & crystal clear coat. , Easy to rework & repair. , Acrylic Base, Protection from moisture, corrosion, dust & temperature.
• Usage/Application: Industrial
• Physical State: Liquid

    Properties:          • Adheres well and forms a even filling Fast drying          • Protects PCB's from dust, dirt and other foreign particles          • Excellent electric insulating property   Applications:          • Specially formulated to protect PCB assemblies

• Shelf Life: 24 Months from Date of Manufacture in Sealed Condition.
• Packaging: 400 Ml Aerosol Spray - 550 Ml Aerosol Spray

High Gloss Fast Drying Flexible Acrylic Conformal CoatingELECTOCOAT is a fast air-drying, lightweight, clear, tough and flexible acrylic coating designed primarily to protect printed circuit boards and electrical / electronic equipment against high voltage arcing, corona shorts, corrosion, ingress of moisture and fungus. It resists rust, tarnish, corrosion, moisture and has excellent waterproofing / weatherproofing abilities. ELECTOCOAT is highly abrasion & scratch resistant and protects electronic equipment completely due to its high dielectric strength. It does not contain any harmful chlorinated solvents, CFCs or ozone depleting chemicals.Benefits Protects against rust, corrosion, tarnish, oxidation, moisture and weathering influences Provides a high-gloss, clear protective finish that remains transparent and does not fade or become yellow Provides a protective and insulating film that shields printed circuit boards from electrical leakage and short circuits Prevents sparking and corona discharges Non-conductive and has good dielectric properties Excellent resistance to weak acids & alkalis, water, oils and chemical fumes Easily solderable and very convenient for onsite repair jobs Conforms to requirements of specifications MIL-I-46058C Applications Insulation and protection of all electrical, electronic and high- tech equipment of: general electronics, printed circuit boards, thick film circuits, high voltage transformers, electrical motor coils, cables, wires; for moisture proofing and corrosion prevention of any industrial, automotive, aviation, marine and military electrical & electronic hardware.Directions For Use - Bulk Mask and protect areas not to be coated. Apply steady even strokes by means of brush. Component to be coated can also be dipped into the coating. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity.Directions For Use - Aerosol Shake can vigorously for at least one minute after bearing noise from inside the can is audible. Mask and protect areas not to be coated. Hold can 12-15 inches away from surface to be coated and spray in steady, even strokes. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity. Clean the valve by inverting the can and spraying a few short bursts till only the clear propellant comes out. Clean the actuator button orifice by means of a thin, fine wire.Caution:- Contains flammable propellant and solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

We are offering pcb conformal coating

• Brand: Sanpra
• Packaging Size: 550ml
• Packaging Type: Can
• Physical State: Liquid
• Usage/Application: Industrial
• Country of Origin: Made in India
• Grade: SPN-3141

• Packaging Size: 500 ML
• Packaging Type: CAN
• Brand: ACRYLCOAT
• Grade Standard: Technical Grade
• Physical State: Liquid
• Usage/Application: Industrial
• Country of Origin: Made in India
• Features : Acrylcoat Solderable, Conformal Coating for PCB Assemblies, 100% Eco - Friendly, Economical in use., Good Dielectric strength, Excellent adhesion to all surfaces

• Features: Purity , Effectiveness , Correct composition .
• Application: Used for coating of PCB
• Packaging Size: 400 ml / 500 ml
• Brand Name: Miracle
• Grade: Analytical Grade
• Physical State: Liquid
• Application: Industrial
• Country of Origin: Made in India

• Usage/Application: Industrial
• Physical State: Liquid
• Packaging Size: 500 ml
• Brand: Spraysol
• Packaging Type: Aerosol Can
• Grade Standard: Reagent Grade
• Country of Origin: Made in India

  PCB Coating is a single component acrylic plastic coating,fat drying,conformal,water clear transparency,good electrical properties, high resistance to burning, heat,cold,silts,alkalies,mild acids-will not peel crack or dis-color,solder through and removable is not required if required, lasting protection against wear, handling and oxidation, excellent thermal conductivity.

• Packaging Size: 300 ml
• Packaging Type: Spray
• Grade Standard: Reagent Grade
• Color: White
• Country of Origin: Made in India
• Usage/Application: Industrial
• Physical State: Liquid

• Brand: Automotive Solutions
• Physical State: Liquid
• Packaging Type: Bottle
• Usage: Personal
• Packaging Size: 300 ML
• Color: Clear
• Features : High Moisture & Chemical Resistant, Fast Drying, Transparent 

PCB Conformal Coatings, Rubber, Pvc Spacers, Eyelets, sleevings

PCB AND LED Conformal Coating, Rechargeable Battery Bank, Push Button Switch

PCB Coating Spray, Anti Seize Copper Paste, high speed grease

PCB Conformal Coating, Flame Spray Coating, High Temp Rtv Liquid Gaskets

PCB Coating Spray, Cold Galvanizing Zinc Coating

PCB Coating Spray, Purging Compound, Silicone Oil, Release Agents

pcb conformal coating spray, auto shine dash board, auto rub rubbing compound