Programmable Microcontroller Dealers

8051 CPU operating @ 10/12 MHz. 8K user RAM with Battery Backup, 16K bytes monitor EPROM Peripherals like 2x 8255 brought, 8253,8251, RS-232 interface 25 Keys Hexadecimal Keyboard and 6 digit 7-segment display using 8279 In-Built Power Supply of +5V/1.5A, ±12V/250mA

We are offering pro mini microcontroller boards. The arduino pro mini is a microcontroller board based on the atmega168 (datasheet). It has 14 digital inputoutput pins (of which 6 can be used as pwm outputs), 8 analog inputs, an on-board resonator, a reset button, and holes for mounting pin headers. A six pin header can be connected to an ftdi cable or sparkfun breakout board to provide usb power and communication to the board. The arduino pro mini is intended for semi-permanent installation in objects or exhibitions. The board comes without pre-mounted headers, allowing the use of various types of connectors or direct soldering of wires. The pin layout is compatible with the arduino mini. There are two version of the pro mini. One runs at 3.3v and 8 mhz, the other at 5v and 16 mhz. The arduino pro mini was designed and manufactured by sparkfun electronics.

Package Includes·         Fully Assembled and Tested Development Board with LPC1114 Microcontroller·         Serial Port Cable for PC interfacing and programming·          CDROM containing Flash Magic – Programming Software and User ManualIntroductionInterLogicx ILXLPC1114 is a development board for NXP LPC1114 microcontroller. The ILXLPC1114 board supports on board ISP Circuit for programming Flash memory via the board’s RS232 port eliminating the need for separate device programmer. On-board switch toggles between programming and code execution modes. All the microcontroller’s I/O ports are accessible via standard external headers for easy interfacing of external devices.Features·          Easy programming of the flash memory with a serial port of a computer. ·         Toggling between programming/execution modes with a single switch eliminating the need for any complex changes in the hardware. ·         Output Headers provide access to all port pins for easy interfacing to external devices ·         Target embedded microcontroller LPC1114 is supplied with kit.·          On-Board RS232 Port for direct connection to PC’s Serial Port·          Hex file can be downloaded easily with the help of a user-friendly Flash Magic SoftwareSpecifications·         ARM Cortex-M0 processor, running at frequencies of up to 50 MHz·         32KByte on-chip Flash ROM with In-System Programming (ISP) and ·         In-Application Programming (IAP) via 12KByte On-Chip Boot loader, 4KByte SRAM,·         Nested Vectored Interrupt Controller,  1 SSP controller·         UART with full Modem Interface and RS485 Support·         Fast Mode I2C-Bus, 4 Timers with 4 capture channels and 13 output channels·         Watchdog (WDT), System tick timer, 10-bit ADC with 8 channels, 42 GPIO, Serial Wire Debug/Trace port.        Applications •   Access control•   Point-of-sale•   Communication gateway•   Embedded soft modem•   General purpose applicationsPrograms Intel Hex files •   Straightforward and intuitive user interface •   Requires RS-232 port of PC for operation•   Five simple steps to program the flash deviceSystem Requirements•   Windows XP /7•   RS-232 Port •   16MB RAM •   3MB Disk Space

Arduino Uno is a microcontroller board based on the ATmega328P (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator (CSTCE16M0V53-R0), a USB connection, a power jack, an ICSP header and a reset button.

The UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.   Arduino/Genuino Uno is a microcontroller board based on the ATmega328P. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.. You can tinker with your UNO without worring too much about doing something wrong, worst case scenario you can replace the chip easily at a reasonable price and start over again.

The Arduino Uno R3 is a open source microcontroller board based on the ATmega328 chip. This Board has 14 digital inputoutput pins, 6 analog input pins, Onboard 16 MHz ceramic resonator, Port for USB connection, Onboard DC power jack, An ICSP header and a microcontroller reset button. It contains everything needed to support the microcontroller. Using the board is also very easy, simply connect it to a computer with a USB cable or power it with DC adapter or battery to get started.The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2Atmega8U2 up to version R2) programmed as a USB-to-serial converter. While the Arduino UNO can be powered via the USB connection or with an external power supply, the power source is selected automatically.External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the board's power jack. Also leads from a battery can be inserted in the Gnd and Vin pin headers of the Power connector. The board can operate on an external supply of 6 to 20 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable. If using more than 12V, the voltage regulator may overheat and damage the board. The recommended range is 5v to 12v for Arduino Uno.

PROJECT NAME: Arduino Uno PROJECT DESCRIPTION: The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital inputoutput pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 (Atmega8U2 up to version R2) programmed as a USB-to-serial converter. Revision 2 of the Uno board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode. Revision 3 of the board has the following new features: · 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Arduino Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. · Stronger RESET circuit. · Atmega 16U2 replace the 8U2. "Uno" means one in Italian and is named to mark the upcoming release of Arduino 1.0. The Uno and version 1.0 will be the reference versions of Arduino, moving forward. The Uno is the latest in a series of USB Arduino boards, and the reference model for the Arduino platform. This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory.

Arduino uno price in india The Leonardo is a microcontroller board based on the ATmega32u4. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Leonardo differs from all preceding boards in that the ATmega32u4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Leonardo to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port.