Robokits India Gandhinagar, Gujarat

Water Sensor water level sensor is an easy-to-use, cost-effective high leveldrop recognition sensor, which is obtained by having a series of parallel wires exposed traces measured dropletswater volume in order to determine the water level. Easy to complete water to analog signal conversion and output analog values can be directly read Arduino development board to achieve the level alarm effect.

Water Sensor water level sensor is an easy-to-use, cost-effective high leveldrop recognition sensor, which is obtained by having a series of parallel wires exposed traces measured dropletswater volume in order to determine the water level. Easy to complete water to analog signal conversion and output analog values can be directly read Arduino development board to achieve the level alarm effect.

This Voice Recognition Module is a compact and easy-control speaking recognition board. This product is a speaker-dependent voice recognition module. It supports up to 80 voice commands in all. Max 7 voice commands could work at the same time. Any sound could be trained as command. Users need to train the module first before let it recognizing any voice command. This board has 2 controlling ways: Serial Port (full function), General Input Pins (part of function). General Output Pins on the board could generate several kinds of waves while corresponding voice command was recognized. Parameters

Size : 30mm x 47.5mm

AVR USB Programmer is a low cost STK500V2 compatible In-System Programmer (ISP). It is supported in all operating systems including Windows 2000, XP, Vista, Windows 7, windows 8 & windows 10.

The USB-RS485 module provides an easy to use RS485 interface by means of a Virtual Com Port on the users system. There are no command structures, whatever is sent to the Virtual Comm Port is automatically converted to RS485 and vice versa. The module is completely self powered from the USB bus.

This sensor is a high performance ultrasonic range finder. It is compact and measures an amazingly wide range from 2cm to 4m. This ranger is a perfect for any robotic application, or any other projects requiring accurate ranging information. This sensor can be connected directly to the digital IO lines of your microcontroller and distance can be measured in time required for travelling of sound signal using simple formula as below.

RF Remote with four channel output. Directly gives TTL on for a corresponding switch press.RF Remote with four channel output. Directly gives TTL on for a corresponding switch press.

The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the modules output is low, lower power consumption; When a finger touches the corresponding position, the modules output is high, if not touched for 12 seconds, it switches to low-power mode. Jog type : the initial state is lower , higher touch , do not touch is lower ( similar touch of a button feature ) This Module can be installed in such as surface plastic, glass of non-metallic materials.In addition to the thin paper ( non-metallic ) covering the surface of the module , as long as the correct location of the touch , you can make hidden in the walls, desktops and other parts of buttons.

This tilt sensor is used to detect the inclination. It is a mercury switch where the glass fills with mercury. It acts as on-off switch for some pre-set angle.

Two-Phase Hybrid Servo 80V 7Amp Drive fully compatible with RMCS-1051 Hybrid 2-Phase Stepper Servo Motor. It is operated through a Modbus Master Devices like Arduino, PLC and HMI. It is compatible with 85kg-cm, 70kg-cm, 33kg-cm motors.

It is a high quality small spindle motor for the engraving machine works on 12-48VDC. Spindle motor can be used for curving metal or non-metallic materials. It includes cooling fan and the shank.

The Sound Sensor can detect the sound strength of the environment. The main component of the module is a simple microphone and LM393 level convertor chip. The sensor can provide both digital aswell as analog output.

This is a simple water sensor, can be used to detect soil moisture Module Output is high level when the soil moisture deficit,or output is low.

USB 16 Servo Controller is ideal for making PC based systems which run over Hobby Servo motors. The software helps to develop the complex sequences in real time on the hardware like robotic arms, walkers, bipeds and any other servo controlled system. The compact module measures just 80 mm X 47 mm, and it offers both USB and asynchronous serial (UART) connectivity. No features are compromised for the small size, as our USB controller supports independent speed and range settings for each servo while delivering 0.5-microsecond resolution for smooth output across its broad output pulse range of 200 through 2400 microseconds.

Its a high quality 30-pulse encoder, with detents and a nice feel to it. It is panel mountable for placement in a box, or can be pluged into a breadboard (just cutbend the two mechanical side tabs). This encoder also has a push-button built into it so you can press onto the knob to close a separate switch. One side has a 3 pin connector (ground and two coding pins) and the other side has two pins for a normally-open switch. Rotary encoders are useful as rotation sensors or selectors and look similar to potentiometers. These rotary encoders rotate all the way around continuously, and are divided up into 30 segments. Each segment has a click-y feeling to it, and each movement clockwise or counter-clockwise causes the two switches to open and close. There is no way to know what the current position is - instead we would need to use a microcontroller to count how many clicks left or right it has been turned.

Can grip and lift upto 200 gm of load in form of small objects. Maximum opening 3.5cm. Servo motors are not included in price of the gripper module. Use Standard Dual Ball Bearing Servo for best result.

E: Summed for even parity O: Summed for odd parity P: parity(even or odd ) D: Data code for card: the data will use the last 24 data bits of card

The RX – ASK is an ASK Hybrid receiver module. It is a effective low cost solution for using 433 MHz. The TX-ASK is an ASK hybrid transmitter module. TX-ASK is designed by the saw resonator, with an effective low cost, small size and simple to use for designing. Please note that this device will not support direct UART communication when connected to PC or microcontrollers as there is a lot of noise always available on these frequencies. If you are looking for Serial Communication see RF 2.4Ghz Serial Link instead of this product. We will not be providing any support for serial communications after sales. For remote control applications please use Encoder and Decoder ICs.

RX Operating Voltage : 5V

The wireless transmitter receiver has a radial range of minimum 500 meters to a maximum of 1km line of sight in an open air environment. Please note that this range is where there is no RF interference in 2.4Ghz band. In cities and areas with lots of wifi networks around the range can be drastically low than specified. Control 2 DC motors with Skid Steer Control with 20Amp capacity each (See Remote Functions below) Analog speed control for 2 DC driving DC motors

The RX – ASK is an ASK Hybrid receiver module. It is a effective low cost solution for using 433 MHz. The TX-ASK is an ASK hybrid transmitter module. TX-ASK is designed by the saw resonator, with an effective low cost, small size and simple to use for designing. Please note that this device will not support direct UART communication when connected to PC or microcontrollers as there is a lot of noise always available on these frequencies. If you are looking for Serial Communication see RF 2.4Ghz Serial Link instead of this product. We will not be providing any support for serial communications after sales. For remote control applications please use Encoder and Decoder ICs.

RF Remote with four channel output. Directly gives TTL on for a corresponding switch press.RF Remote with four channel output. Directly gives TTL on for a corresponding switch press.

This is a small device called a reed switch. When the device is exposed to a magnetic field, the two ferrous materials inside the switch pull together and the switch closes. When the magnetic field is removed, the reeds separate and the switch opens. This makes for a great non-contact switch. This switch can carry up to 1.2A.

Accuracy : Sensing Area 9.53mm