L. J. Technologies ECIL, Hyderabad, Telangana

Wear Studs are widely used in the Earth-moving and Mining Industries. They are essentially small hardened metal buttons, installed in close formation to form a dense pattern and a barrier between the product being moved and the base material. Used successfully in reducing wear on buckets, loaders, crushers, tipper trays, or any surface subject to high abrasion from dirt, rock and ore. Wear studs are used in some of the worst wear situations imaginable, they can extend wear life between 3 and 10 times that of traditional 'quench and tempered plate' or 'hard facing'. Of course wear life is dependent on particle type, hardness, size and many other factors.    

Our triangular 3 meter-section towers are low cost structures, used in RF Radio Communications and Telemetry applications. They are made of steed tubes, reinforced with solid steel rods as ZIG-ZAG cross-pieces for strength and convenience of climbing. Tower and accessories are hot-dipped galvanized to ensure durability and resistance to most adverse weather conditions.   Applications: - RF RadioCommunications - Telemetry - Internet Links - Security

Street Lighting Poles For roadway and highway lighting.Round or conical shape with heights from 8 thru 12 M.With hot dip galvanize and painted finish.For playgrounds, car parks and large open areas,Flexibility, ease of installation, maintenance free, reliability .... These are just some of the advantages provided by our galvanized steel monopoles over concrete or lattice structures. We design, manufacture and supply any tapered steel poles for Transmission networks.

We manufacture tilt over masts for numerous applications. This can carry antenna loads up to 300 Kgs. We can offer various heights of Tilt Over Masts with mounting applications to suit customer requirements. Find few applications of Tilt over Masts as below: - Navigation - Meteorology - Communications - Defense

Shear connectors or Concrete Anchors, are used in Steel-Concrete composite structures. They act as reinforcing anchors, locking the supporting structure to the concrete floor.   We manufacture Shear Connectors/Studs sizes starting from 9.5 mm to 25 mm Dia, in different lengths max 300mm. We are producing Shear Connectors as per following Standards: - AWS D1.1 - ISO 13918 - JIS B1198 Shear Connectors are available for welding to flat surfaces, inside angles and out side angles. Suitable ceramic ferrules will be supplied for above mentioned welding applications.

We are leading manufactures Telecommunication/Microwave/Communication Towers. We are an ISO 9001:2008 certified company. We deal in Design, Fabrication, Hot-Dip Galvanization, Foundation, Erection, Painting and maintenance of Telecommunication/Microwave/Communication Towers. These towers are precision designed to deliver long lasting performance even in toughest working conditions. The optimization of manufacturing facilities and incorporation of top standard accessories ensure the effective functionality of these towers. These towers are carefully engineered to handle the medium to heavy-duty applications. These Telecommunication/Microwave/Communication Towers can be constructed in many ways, but most efficient use of material will be achieved by using Open Lattice Steel Structure.   We offer following Self Supported Lattice Towers: Based on cross section: - Square Towers - Rectangular Towers - Triangular Towers - Delta Towers Based on type of sections used for construction: - Angular Towers - Tubular Towers - Hybrid Towers (Legs Tubes & Bracings Angles) Based on placement of towers: - Ground Based Towers (GBT) - Roof Top Towers (RTT)

Punching Shear Resistant Studs or PSR Studs are a reinforcing studs welding to rails, and used around columns on traditional formwork constructed buildings. They are used to reduce the likelihood of Punching Shear forces, or the desire for the column to punch its way thru the slab due to the floor loading. Punching Shear Resistant Studs can reduce the need for heavy reinforcing bars around these high stress areas, and can remove the need for a 'Capital' altogether. (A capital is a large usually square, section of thickened floor around the column.

Pneumatic Telescopic Mast is a latest innovation, forming part of an integral communication of systems. These masts are light weight and meant for quick erection, ranging from 5 to 25meters height. Pneumatic masts are extended by using low pressure air. The accessories supplied either from a compressor, in case of smaller masts, from a foot pump.   We offer Pneumatic Telescopic Masts as per JSS 55555 Environmental Specs. Applications: - Military Communications - Surveillance - Elevated Testing - Mobile Radar - Areal Photography - Meteorology

Country of Origin : India

Size : 14-16ft, 16-18ft, 18-20ft, up to 30 Meters

Number Of Flower : Pneumatic Telescopic Masts

Material : Alloyed Aluminium

Application : Scienticfic Use, Defense and Communication

Feature : Hard Structure, High Acurace, Rust Proof

cetification : ISI Certified

Mounting Type : Floor Mounted, Wall Mounted, Vehicle Mountable

Country of Origin : India

Material : Aluminum Alloy

Size : Up to 30 Meters Height

We can take up design, fabrication, galvanizing, supply, foundation and erection of Meteorological Towers, Masts and Poles with high quality of workmanship at reasonable prices.   We can supply Meteorological Towers of height starting from 6 Mtr. up to 120 Mtr.

We are well experienced in Fabrication of metal Items and Precession Machined Parts Industry. We have very big establishment in Hyderabad located in southern India. We can take up any critical fabrication jobs as well High Precession Machined Parts at very reasonable cost, with high quality workmanship.

High Alumina Refractory Cement is manufactured from Calcined Alumina and high purity lime. It is used as a binder for all types of castable refractory's.

We are well experienced in Fabrication of metal Items and Precession Machined Parts Industry. We have very big establishment in Hyderabad located in southern India. We can take up any critical fabrication jobs as well High Precession Machined Parts at very reasonable cost, with high quality workmanship.    

Guyed towers/masts provides given towers/masts height at lower material cost than self-supporting towers due to the efficient use of high strength steel wire rope support. Guyed towers/masts are in square or triangular cross section and angular or tubular sections are used for construction.   Guyed masts are normally guyed in three directions for triangular cross sectional towers and in four directions for square cross sectional towers.   Triangular cross sectional towers/masts are used for minimize icing load on towers/masts, where icing is very heavy. These guyed towers/masts are much lighter than self-supporting type towers, but need a large free space to anchor guy wires. So guyed towers/masts are preferred where large open space is available.   These towers were find application in communication and Meteorological fields.

The electromechanical telescopic mast is made of high tensile aluminum alloy or Stainless Steel sections. The sections are extended or retracted by a screw rod or winch mechanism driven by suitable electric motor. It can also be operated manually. These masts are offered with extended heights from 3 to 21 Mtrs with self supporting and guy supporting options, with load of Max 100 Kgs.   Applications: - Navigation - Communications - Defense - Telecom - Cellular on Wheels (COW)

We are engaged in Design and Manufacturing of Steel Structures for Electrical Transmission and Distribution networks. What we offer: * Street Lighting Poles - For roadway and highway lighting. - Round or conical shape with heights from 8 thru 12 M. - With hot dip galvanize and painted finish. * Area Lighting and High Mast Poles - For playgrounds, car parks and large open areas - Octagonal shapes 5 thru 12 M - Hot dip galvanized and painted * Transmission Poles Flexibility, ease of installation, maintenance free, reliability .... These are just some of the advantages provided by our galvanized steel monopoles over concrete or lattice structures. We design, manufacture and supply any tapered steel poles for Transmission networks.

Drawn Arc Weld Studs, Threaded and un-threaded studs, Collar Studs, Headed Shear Connectors, bended , tapped studs, refractory anchors, Material : Low Carbon Steel, Grade 8.8 Steel, Stainless Steel 304, 304 L, 316 L, 316 Ti , 310, Aluminum, Inconel

Diameter : 3 up till 30 mm

Our Radar Towers are of a four legged construction, self supporting and made of angular and tubular elements.   These Radar Towers are designed for medium to heavy loads and easy staircase access to the antennas and equipment mounted on it. Radar Towers are designed for maximum heights of up to 50m. Its modular design allows for last minute modification in height and loads.   Our Radar Towers are supplied with variety of accessories, such as elevator, work platforms, antenna mounts, safety devices, obstruction lights, lightning protection kit and more. All of these accessories can be installed at any desired height and orientation according to customer requirements We have wide experience in Design, manufacturing and Installation of Broadcasting Towers up to 150 Mtr. height, for FM, MW and TV Broadcasting.Our Radar Towers are supplied with variety of accessories, such as elevator, work platforms, antenna mounts, safety devices, obstruction lights, lightning protection kit and more. All of these accessories can be installed at any desired height and orientation according to customer requirements We have wide experience in Design, manufacturing and Installation of Broadcasting Towers up to 150 Mtr. height, for FM, MW and TV Broadcasting.

- Drawn Arc Weld Studs - Threaded and un-threaded studs, Collar Studs, Headed Shear Connectors, bended , tapped studs, refractory anchors - Diameter : 3 up till 30 mm diameter - Material : Low Carbon Steel, Grade 8.8 Steel, Stainless Steel 304, 304 L, 316 L, 316 Ti , 310, Aluminum, Inconel - Capacitors Discharge (CD) Studs - Threaded, unthreaded, tapped studs, flanged & deflanged and earth tags - Diameter : 3 to 10 mm in Mild Steel 4.8, Steel 6.8 and Stainless Steel 304, 316 L - Diameter : 3 to 8 mm in Aluminum and Brass - Short Cycle (SC) Studs - Threaded, unthreaded, tapped studs, flanged & deflanged - Diameter : 3 to 10 mm - Materials : Mild steel 4.8, Steel class 6.8 & 8.8, Stainless Steel 304 & 316 L, aluminum. - Inert Gas Studs - Threaded, unthreaded and tapped studs - Diameter : 3 up till 10 mm diameter - Material : Low Carbon Steel, Stainless Steel, Aluminum

High Alumina Refractory Cement is manufactured from Calcined Alumina and high purity lime. It is used as a binder for all types of castable refractory's.Al2O3 - 72.00 % Min.Fe2O3 - 0.30 % Max.CaO - 25.00% Max.SiO2 - 1.00% Max,2. C.CS. Kg Cm2 (With standard sand and cured at 180 C + 20 C to 24 Hrs.) - 300 Min.3. C.CS kg Cm2 at 110OC24 Hrs - 500 Min.