Haldia Petrochemicals Limited Salt Lake, Kolkata, West Bengal

The down-time, shut down, profit loss, energy decline, safety hazards pose major threat to many Industries. Monarch's SavesPast range of Epoxy Cold Welding Compound offers wide range of products and service during routine and unexpected maintenance to solve the maintenance issues that arise from machinery and equipment break-downs and failures across wide spectrum of Industries. These 2 component epoxy putties containing Resin and Hardener which after mixing hardens to a firm metal like material, well adhering to almost any kind of surface. It rebuilds worn-out surface to the original specifications, in most of the cases in less than 2 hours down-time saving huge inventory replacement cost. The surface of the base substrate is not altered as in case of soldering or welding and no thermal stresses are induced during repair. The cured mass can be painted, sanded, machined, tapped, ground, filed or drilled.

Multi-Purpose Reclamation Putty for high temperature resistance till 230°C A two component paste, engineering grade system based on a ferro-silicon filled epoxy system on high temperature resistance special resin. The non-rusting putty extensively used for repairing and rebuilding worn-out surfaces in machinery & equipment and precision critical applications in less down-time for high temperature service conditions. The high temperature putty requires post-curing for proper performance and temperature resistance. To achieve permanent temperature resistance do POST CURINGTEMPER HARDENING: High temperatures putty under ambient temperature conditions will take some time to cure to its ultimate properties. Post curing in an oven or by using heat lamps, to a maximum temperature of 150°C for 2 hours, will result in rapid achievement of full cure properties. In-situ cure at the normal process operating temperatures will provide cured properties and an ultimate cure rate consistent with the process temperature.

All the materials used for construction of building absorb and transfer heat inside of the building all the day. Heat always flow from the warmer side to cooler side and cooler to warmer side. 80% to 95% of heat gain during summer and about 70% of heat loss during winter trasferred through the walls, ceiling and roofs of the building by way of conduction and radiation. The conventional insulation only slows down the rate of heat transfer which after saturation cannot stop radiant heat. Monarch’s OzoProtect Heat Solar Reflective Coatings reflects up to 92% of heat back to its source. Monarch's Ozoprotect specialized coating containing ceramic microspheres and or glass microspheres keeps you cooler in the summer and warmer in the winter reducing cooling cost during summer months and heating cost during winter months. The load reduction of air conditioning or heater and corresponding electrical consumption saves energy cost up to 20% all round year. The payback period is less than 6 months. OzoProtect significantly contributes to green building certification as Solar Reflectance Index (SRI) is 108 and prevention of global warming besides reducing evaporation loss in petroleum storage tanks.

All the materials used for construction of building absorb and transfer heat inside of the building all the day. Heat always flow from the warmer side to cooler side and cooler to warmer side. 80% to 95% of heat gain during summer and about 70% of heat loss during winter trasferred through the walls, ceiling and roofs of the building by way of conduction and radiation. The conventional insulation only slows down the rate of heat transfer which after saturation cannot stop radiant heat.

HPL manufactures 3,41,000 tonnes polypropylene per annum using Spheripol-II technology supplied by Basell, Netherlands. Spheripol process is the most widely accepted technology for manufacturing Homopolymers and Copolymer grades. The unique process capabilities and high consistency in product morphology ensure excellent quality. These products from HPL are of benchmark quality, meeting the highest international standards and are used extensively by packaging, consumer durables, houseware, furniture, container or luggage manufacturers in India and abroad. Due to superior quality, HPL products are in demand in various countries from EU, South East Asia, USA etc. HPL products are exported to several countries in the world. Major Brands, Grades End Uses

All the materials used for construction of building absorb and transfer heat inside of the building all the day. Heat always flow from the warmer side to cooler side and cooler to warmer side. 80% to 95% of heat gain during summer and about 70% of heat loss during winter trasferred through the walls, ceiling and roofs of the building by way of conduction and radiation. The conventional insulation only slows down the rate of heat transfer which after saturation cannot stop radiant heat.

These products from HPL are of benchmark quality, meeting the highest international standards and are used extensively by packaging, consumer durables, houseware, automobiles, furniture, container or luggage manufacturers in India and abroad. Due to superior quality, HPL products are in demand in various countries from EU, South East Asia, USA etc. HPL products are exported to more than 20 countries in the world.

HPL manufactures 3,41,000 tonnes polypropylene per annum using Spheripol-II technology supplied by Basell, Netherlands. Spheripol process is the most widely accepted technology for manufacturing Homopolymers and Copolymer grades. The unique process capabilities and high consistency in product morphology ensure excellent quality. These products from HPL are of benchmark quality, meeting the highest international standards and are used extensively by packaging, consumer durables, houseware, furniture, container or luggage manufacturers in India and abroad. Due to superior quality, HPL products are in demand in various countries from EU, South East Asia, USA etc. HPL products are exported to several countries in the world. Major Brands, Grades End Uses

HPL manufactures 3,41,000 tonnes polypropylene per annum using Spheripol-II technology supplied by Basell, Netherlands. Spheripol process is the most widely accepted technology for manufacturing Homopolymers and Copolymer grades. The unique process capabilities and high consistency in product morphology ensure excellent quality. These products from HPL are of benchmark quality, meeting the highest international standards and are used extensively by packaging, consumer durables, houseware, furniture, container or luggage manufacturers in India and abroad. Due to superior quality, HPL products are in demand in various countries from EU, South East Asia, USA etc. HPL products are exported to several countries in the world.

Cyclopentane is a flammable alicyclic hydrocarbon with chemical formula C5H10. Cyclopentane is mainly used as Green blowing agent in Polyurethane foam used for thermal insulation in refrigerators, freezers, water heaters, insulated pipes & roofs, construction panels, etc. Cyclopentane is also used in the manufacture of resin, adhesives, pharma intermediate and as a gasoline additive as octane booster. Cyclopentane being halogen free compound is environment friendly with Zero-Ozone Depletion Potential and thus is fast replacing Chloro Fluoro Carbon (CFC ) applications in refrigeration and thermal insulation.

Benzene is an organic chemical compound. It is an aromatic hydrocarbon composed of 6 carbon atoms in a ring, with 1 hydrogen atom attached to each carbon atom, with the molecular formula C6h5. Benzene is a natural constituent of crude oil, and is one of the most basic petrochemicals. It is a colorless and highly flammable liquid with a sweet smell. Benzene is an important precursor to basic industrial chemicals including drugs, plastics, synthetic rubber, and dyes. It is mainly used as an intermediate chemical to make downstream industrial chemicals to be further used in value chain for manufacturer of end use products. Its most widely-produced derivatives include- Styrene, used to make polymers, plastics and synthetic rubber Phenol (via cumene), for drugs, synthetic resins and adhesives Cyclohexane, used for Caprolactum in manufacture of Nylon Nitrobenzene for Aniline used for MDI (for polyurethane) and dyestuffs Chlorobenzene, used for pesticides (DDT) , herbicides and solvents Alkyl Benzene, for LAB Sulphonate used for laundry detergents & industrial cleaners

71602W is a LLDPE film grade produced by the Spherilene Technology 71602W is without slip additives and antiblock & can be used in General Purpose Packaging Film Application The precise morphological control achieved during polymerization confers good processability & mechanical strengths Property T

HPL also manufacturers various grades of LLDPE in the swing LLDPE plant using Spherilene Gas Phase Swing Process from Basell, Netherlands. The LLDPE plant is the 3rd such plant worldwide using above technology and is used for manufacturing of various HDPE grades too. These products from HPL are of benchmark quality, meeting the highest international standards and are used extensively by packaging, consumer durables, houseware, automobiles, furniture, container or luggage manufacturers in India and abroad. Due to superior quality, HPL products are in demand in various countries from EU, South East Asia, USA etc. HPL products are exported to more than 20 countries in the world.

F5400 is a film grade HM-HDPE manufactured using the Mitsui CX Technology. This grade is characterized by excellent processability and high mechanical strength. F5400 can be used for general-purpose films as well as very thin reinforced bags.

Haldia Petrochemicals Limited is the second largest manufacturer of polyethylene in India with a total capacity of over 7, 00,000 tonnes per annum. It caters to more than 70% of the demand in eastern India and 30% on overall country basis. The product portfolio under polyethylene segment consists of various grades of High Density Polyethylene (HDPE) and Linear Low Density Polyethylene (LLDPE). HPL manufactures a wide range of HDPE grades having narrow, medium & broad (bi-modal) molecular weight distribution using Mitsui Slurry CX Process to suit a wide range of end uses

hese products from HPL are of benchmark quality, meeting the highest international standards and are used extensively by packaging, consumer durables, houseware, automobiles, furniture, container or luggage manufacturers in India and abroad. Due to superior quality, HPL products are in demand in various countries from EU, South East Asia, USA etc. HPL products are exported to more than 20 countries in the world.

All the materials used for construction of building absorb and transfer heat inside of the building all the day. Heat always flow from the warmer side to cooler side and cooler to warmer side. 80% to 95% of heat gain during summer and about 70% of heat loss during winter trasferred through the walls, ceiling and roofs of the building by way of conduction and radiation. The conventional insulation only slows down the rate of heat transfer which after saturation cannot stop radiant heat. Monarch’s OzoProtect Heat Solar Reflective Coatings reflects up to 92% of heat back to its source. Monarch's Ozoprotect specialized coating containing ceramic microspheres and or glass microspheres keeps you cooler in the summer and warmer in the winter reducing cooling cost during summer months and heating cost during winter months. The load reduction of air conditioning or heater and corresponding electrical consumption saves energy cost up to 20% all round year. The payback period is less than 6 months. OzoProtect significantly contributes to green building certification as Solar Reflectance Index (SRI) is 108 and prevention of global warming besides reducing evaporation loss in petroleum storage tanks.

HD T10 is a HDPE yarn monofilament grade produced by Spherilene Technology This grade can be used in yarns monofilament for Fabrics, Nets, Twines & Ropes HD T10 is characterized by excellent processability and mechanical strength

The corrosion is wearing of metal on exposed, uncoated surfaces of structural steel, utilities and technical installations. The typical problems are galvanic corrosion, pitting corrosion, crevice corrosion, microbial corrosion, chemical attack due to organic inorganic acids, alkalis, saline atmosphere, sub-soil conditions, extremes of weather etc., The protective coatings provide barrier between damaging enviroinment and structures. The failure of coating to protect the assets impact the plant productivity besides increasing year-on-year operating expenses.

The flooring is the most abusive part of any Industrial, Commercial or Institutional Building exposing to both physical and chemical abuses like presence of dust, continuous equipment traffic, oil and chemical spillages from occasional to continuous immersion leading to degradation of floor surfaces. Monarch’s FloorClad Floor Screeds & Toppings offers Seamless high performance flooring system with high chemical, bacterial and abrasion resistance to enhance floor design life. The ultimate convenience of easy to clean surface with increased resistance to liquid penetration. The toughness and durability of the hygienic coating along with choice of attractive colors suits to variety of environmental conditions. The coated decorative surface presents ideal and pleasant working atmosphere. FloorClad have wide options of underlayment, screed mortars and floor toppings. The comprehensive range covers - cementitious underlayment, coving, floor marking, re-lay over- lay coatings, epoxy and polyurethane based mortars and floor toppings, anti static ESD conductive floor toppings, poly urea coatings, slip resistant and chemical resistant toppings and silicate floor coatings.