Kjn Enterprises Andheri East, Mumbai, Maharashtra

The X-Stream Hand Vac is the low cost solution to a variety of industrial housekeeping applications. It is a blow gun, a vacuum gun, a collection system and a transfer system in one simple package. The X-Stream Hand Vac is lightweight die cast aluminum and uses less air than a normal blow gun. It draws a vacuum at one end to produce a high vacuum for collection or transfer of materials. It is easily converted from a blow gun into a vacuum gun and back again. It can also be used to transfer material over a long distance using a vacuum hose which can be supplied. In vacuum mode, it can be used to vacuum up debris if more appropriate than blowing air, and debris can be collected in an available reusable vacuum bag. APPLICATIONS No moving parts Driven by air not electricity Die cast construction Can switch from blowoff mode to vacuum in seconds Lightweight and portable ADVANTAGES Maintenance free Safe and long life Durable Flexible in use - vacuum or blowoff Ergonometric - comfortable in use

the nex flow™ stainless steel vortex tube uses a brass generator as a standard item rather than cheap plastic for longer lifespan and for applications in high temperature environments. With virtually no moving parts, the  vortex tube takes compressed air and converts it to cold air at one end and hot air at the other. temperature as low as minus 50° f (minus 46° c) can be achieved at the cold end and up to 260° f (127° c) at the hot end. nex flow vortex tubes are available in three basic sizes and in several packaged versions. applications cool electronic and electrical control cool machine operations/tooling cool cctv cameras set hot melt adhesives cool soldered parts cool gas samples cool heat seals cooling environmental chambers advantages no moving parts, reliable, maintenance free no coolant compact and lightweight low cost application maintenance free units instant cold air in environmental chambers no spark or explosion hazard interchangeable generators

The Flex.US Ultrasonic Leak Detector is a hand held, high quality compressed air leak detection system that has all the features necessary for flexible use in finding costly air leaks. The FLEX.US ultrasonic leak detector kit comes with the FLEX.US unit, carrying case, and manual and utilizestwo AA alkaline batteries(included). The FLEX.US is a complete kit – the high quality flexible sensor is mounted on the end of a flexible steel pipe so the ultrasonic sound can access hard to reach areas. The unit converts the ultrasonic noise of a leak into a sound humans can hear (hissing sound) and not just some beeping sound or LED display that may not distinguish a leak sound fromother phenomenon. The headset has excellent noise attenuation for use in the noisiest of environments. A rugged carrying case protects your FLEX.US when not in use. The FLEX.US is a solid tool – built to last, it is easy to use and will providemany years of service. The FLEX.US ultrasonic leak detector kit comes with the FLEX.US unit and manual and utilizes two AA alkaline batteries (included). The FLEX.US is a complete kit – the high quality flexible sensor is mounted on the end of a flexible steel pipe so the ultrasonic sound can access hard to reach areas. The unit converts the ultrasonic noise of a leak into a sound humans can hear (hissing sound) and not just some beeping sound or LED display that may not distinguish a leak sound from other phenomenon. The headset has excellent noise attenuation for use in the noisiest of environments. A rugged carrying case protects your FLEX.US when not in use. The FLEX.US is a solid tool – built to last, it is easy to use and will provide many years of service.

Frigid-X™ Tool Cooling System for dry machining applications - replaces polluting and often toxic mist systems to improve dry machining operations. No mess, no residue and low in cost. It is efficient and can improve dry machining operations and assist in spot cooling applications for a variety of industrial machining processes but increasing matchining rates and extending tool life. Produces cold air at approximately 50° F (28° C) below supply air temperature. The unit is muffled for quiet operation. No moving parts assures long life, maintenance free operation while extending tool life and improving production rates. Can often replace costly mist coolants and certainly improves the quality and output of all types of dry machining operations from metals to plastics. Unit is low cost, no electricity with no moving parts and is essentially maintenance free. APPLICATIONS Sharpening Tools Routing Machining Plastics Drill And Cutter Grinding Milling, Drilling, Routing And Surface Grinding Plunge And Form Grinding Setting Hot Melt Adhesives Laser Cutting Tire And Rubber Grinding Band Saw Blade Cooling Chill Roll Nip Cooling ADVANTAGES No Moving Parts Quiet Driven By Air, NOT Electricity Small And Lightweight, Portable Milling, Drilling, Routing And Surface Grinding Low In Cost Superior Design And Performance Maintenance Free Operation Made Of Durable Stainless Steel And Metal Arts - NO Cheap Plastic Parts Improves Production Rates And Finished Part Remains Dry Prevents Burning ImprovesTolerance Control Eliminates Coolant Costs System Uses Strong Magnetic Base

The HAUG RN ionizing bars is a powerful and rugged piece of equipment. Its construction satisfies all technical requirements and it has proven its value repeatedly in the removal of electrostatic charges during roll, sheet and web (continuous product) processing. Production interfering surface charges can be removed reliably and effectively, even at high operating speeds. The coaxial high-voltage plug-and-socket connection of the HAUG system X-2000 offers a unique advantage in that the gastight high-voltage plug can be connected to the HAUG power pack easily and without tools. The flexible, coaxially shielded cable connects the ionizing unit with the voltage supply. The round construction of the RN ionizing bars permits the exact axial adjustment in the direction of travel of the material. The ionizing bars is safe to touch. Special wear-resistant electrodes guarantee long service life. APPLICATIONS Plastic processing industry : Film processing, packaging machines, film extruders, etc. Textile industry : Weaving and spinning mills, textile finishing plants, etc. Graphic industry : Screen and pad printing machines, photographic and film processing machines, folding machines, etc. Paint Shops : Car painting, painting of plastic components, etc.

These pneumatic cylinders, like our SPMs, are made as per client's requirement. Some examples of these pneumatic cylinders are: Magnetic Reed Switch-Type Position Sensing Pneumatic Cylinders, Hollow Shaft Cylinders, Stroke Adjustment Cylinders, Tandem Cylinders, Impact Cylinders, Continuously reciprocating Pneumatic Cylinders, Pneumatic Cylinders Special Construction Cylinders, Large Bore - 350 mm Cylinders etc.

The Silent X-Stream™ Frigid-X™ Panel Cooler series for electronic control panels provide a low cost method of both purging and cooling electrical and electronic control panels by using a stainless steel vortex tube to create cold air from ordinary compressed air. Utilizing a hot and cold end muffling kit the unit is made extra quiet to under 64 dBA depending on capacity. The hot end muffler also acts a "heat guard" - you can actually wrap your hand around it without feeling much heat. The hot air is exhausted safely underneath the hot end muffler. The  Silent X-Stream™ Frigid-X™ Panel Cooler series are compact and can be installed in minutes through a standard electrical knockout. There are virtually no moving parts. Features Low in cost Compact No CFC's Fast installation Stabilize enclosure temperature and humidity Virtually maintenance free (No Moving Parts) Mounts in a standard electrical knockout Stops heat damage and nuisance tripping Eliminates fans and filters Prevents dirt contamination by keeping enclosure at positive pressure Units applicable to all environments including high temperature to 200°F

Nex Flow™ Safety Air Guns are durable, safe and comfortable to use incorporating our efficient air nozzles and air jets to produce high output air and "laminar" flow while minimizing compressed air use and noise levels. Nex Flow™ Carries two types of Safety Air Guns to choose from depending on an individual's personal taste and comfort. The Easy Grip Safety Air Gun or the Hand Comfort Button Gun. All Nex Flow Safety Air Guns with Nex Flow Nozzles meet OSHA standard CFR 1910.242(b) for dead end pressure. Noise levels are dramatically lower in addition to lower energy use. Nex Flow™ Safety Air Guns are durable, safe and comfortable to use incorporating our efficient air nozzles to produce high output air and "laminar" flow while minimizing compressed air use and noise levels. APPLICATIONS Dust and scrap blow off.

The Nex Flow Ring Vac Air Conveyor is available in both ANODIZED Aluminum, Heavy Duty HARD Anodized or ALL STAINLESS STEEL. Simply clamp a standard hose size to each end of the Ring-Vac™ to create this high energy conveying system. No moving parts for maintenance free operation with capacity and flow controlled with a pressure regulator. Known as Hopper Loaders or Venturi Loaders, originally designed to eliminate manual bending and lifting. Conveying rate depends on density of material ( Lbs / cubic foot ), horizontal run, vertical lift. These vacuum conveyors provide a simple, low cost solution compared to other pneumatic conveying systems APPLICATIONS Hopper loading Fiber tensioning Material conveying Waste/trim removal Chip removal Part transfer Filling operations ADVANTAGES Compact Quiet No moving parts Fits standard hose or tube Aluminum or stainless steel High throughput capabality

The Nex Flow™'s Ring Blade™ Air Wipe produces an even 360 degree blow off around the part, light in weight and compact. Easy to install and maintain and allows removal of a continuous piece. Reduces compressed air use for energy savings plus lower noise levels. Maintenance free with output easily controlled. Designed as two pieces hinged together to open and close around the part. Instant on-off with no moving parts The 360 Degree Air Wipe System produces a "laminar" flow of air along its 360° angle using the "Coanda" effect which "entrains" a large volume of air from the surrounding area along with the small amount of compressed air from the Air Wipe System to produce an output flow up to 30 times Available in 10 standard (inside) diameters AND in 3 versions: 1/2" - Standard Anodized Aluminum with Brass Fittings & Rubberized Plastic Hose 1/2" - X-Stream Anodized Aluminum with Brass Fittings & Stainless Steel hose for moderate temperatures up to 400 degrees F (204 degrees C) 1/2" - X-Stream 316L Stainless Steel with Stainless Steel Fittings and Hose for high temperatures up to 800 degrees F (427 degrees C) and corrosive environments 1" - Standard Anodized Aluminum with Brass Fittings & Rubberized Plastic Hose 1" - X-Stream Anodized Aluminum with Brass Fittings & Stainless Steel hose for moderate temperatures up to 400 degrees F (204 degrees C) 1" - X-Stream 316L Stainless Steel with Stainless Steel Fittings and Hose for high temperatures up to 800 degrees F (427 degrees C) and corrosive environments 2" - Standard Anodized Aluminum with Brass Fittings & Rubberized Plastic Hose 2" - X-Stream Anodized Aluminum with Brass Fittings & Stainless Steel hose for moderate temperatures up to 400 degrees F (204 degrees C) 2" - X-Stream 316L Stainless Steel with Stainless Steel Fittings and Hose for high temperatures up to 800 degrees F (427 degrees C) and corrosive environments 3" - Standard Anodized Aluminum with Brass Fittings & Rubberized Plastic Hose 3" - X-Stream Anodized Aluminum with Brass Fittings & Stainless Steel hose for moderate temperatures up to 400 degrees F (204 degrees C) 3" - X-Stream 316L Stainless Steel with Stainless Steel Fittings and Hose for high temperatures up to 800 degrees F (427 degrees C) and corrosive environments 4" - Standard Anodized Aluminum with Brass Fittings & Rubberized Plastic Hose 4" - X-Stream Anodized Aluminum with Brass Fittings & Stainless Steel hose for moderate temperatures up to 400 degrees F (204 degrees C) 4" - X-Stream 316L Stainless Steel with Stainless Steel Fittings and Hose for high temperatures up to 800 degrees F (427 degrees C) and corrosive environments 5" - Standard Anodized Aluminum with Brass Fittings & Rubberized Plastic Hose 5" - X-Stream Anodized Aluminum with Brass Fittings & Stainless Steel hose for moderate temperatures up to 400 degrees F (204 degrees C) 5" - X-Stream 316L Stainless Steel with Stainless Steel Fittings and Hose for high temperatures up to 800 degrees F (427 degrees C) and corrosive environments 6" - Standard Anodized Aluminum with Brass Fittings & Rubberized Plastic Hose 6" - X-Stream Anodized Aluminum with Brass Fittings & Stainless Steel hose for moderate temperatures up to 400 degrees F (204 degrees C) 6" - X-Stream 316L Stainless Steel with Stainless Steel Fittings and Hose for high temperatures up to 800 degrees F (427 degrees C) and corrosive environments 7" - Standard Anodized Aluminum with Brass Fittings & Rubberized Plastic Hose 7" - X-Stream Anodized Aluminum with Brass Fittings & Stainless Steel hose for moderate temperatures up to 400 degrees F (204 degrees C) 7" - X-Stream 316L Stainless Steel with Stainless Steel Fittings and Hose for high temperatures up to 800 degrees F (427 degrees C) and corrosive environments 9" - X-Stream Anodized Aluminum for moderate temperatures up to 400 degrees F (204 degrees C) - 4 inlet connections, no hose 11" - X-Stream Anodized Aluminum for moderate temperatures up to 400 degrees F (204 degrees C) - 4 inlet connections, no hose Special diameters for the Air Wipe Blow-Off System - X-Stream™ Ring Blade™ are available on special request from Nex Flow™. Air Wipe Blow-Off System - X-Stream™ Ring Blade™ comes with a standard .002" outlet gap which will work for 90% of all applications encountered. If greater force is required, a second .002" (.05mm) shim may be installed to open the gap for greater flow. Materials of construction anodized aluminum or 316L stainless steel. APPLICATIONS Drying after wash, cleaning, plating or coating Blowoff dust and contaminants Cool hot extruded shapes Uniformly wipe surfaces Dry extruded profiles, rod and medical tubing Blow excess water from automotive door gaskets Remove excess coatings, water and oil Dry tube, hose, wire, fiber optics Clean paint gun tips Dry screen printed or ink jetted surfaces Clean strips and ribbon ADVANTAGES Quiet Low air consumption Uniform airflow across the entire diameter No electricity, no moving parts Non-contact - no wiper blade Lightweight, low profile Split design - compact, rugged, easy to install Stainless steel hardware resists corrosion

The unique Nex Flow RIGID FLEX Hose is an all stainless steel hose that does not break after a few bends like competitive rubber hoses with simple copper inserts. It is resistant to creep and crimping. Its all stainless construction allows is use in any difficult environment. The Nex Flow RIGID FLEX Hose is used to flex, direct and then hold in place air nozzles, air jets and other small blow off products TM TM such as our Model 40001 adjustable air amplifier and 3" X-Stream Air Blade Air Knife. The RIGID FLEX Hose can also be used with liquid spray jets. The rigid flex hose is available in three different sizes 6" (152 mm), 12" (304 mm) and 18"(457 mm) and in two configurations – 1/4? male NPT welded end connection both ends or 1/4" male NPT welded connection one end and female NPT welded connection other end.

Manufactured in 316L Stainless Steel: The Reversible Drum Angel/ Drum Pump is a maintenance free system to recover spilled liquids, coolant, sludge, tramp oil, wastewater and other liquids using only compressed air. The compressed air system attaches easily to any closed head of a drum (30 or 55 US gallon, or 45 Imperial gallon or 205 litre drum) The reversible feature allows you to fill or empty the drum in under two minutes with the simple turn of a knob. Using no electricity, these system last and last, unlike many electrical units that wear out quickly in harsh industrial.

Quick Exhaust valve is used to allow direct exhaust by unrestricted flow to atmosphere from a pressurized system. They are used for increasing piston speed of pneumatic cylinders upto 3 times by allowing quick exhaust of the back pressure on the piston when mounted directly on the exhaust port. Another example of their use is for rapid closure of the pneumatic brake of a power press.

The One-Point-Ionizer OPI was developed for the neutralization of the smallest of parts. Emitting positive and negative ions, this unit reliably neutralizes spot charges. This ionizer is perfectly suited for mounting in places where there is little room. The plug of the electrode must simply be connected to the high voltage transformer (power pack) and the unit can be quickly set into operation without tools. The One-Point-Ionizer OPI has proven its value repeatedly in daily use, e.g. in the medical industry. The OPI can also be equipped with compressed air (Mini-Jet Ionizer). NOTE: The pin carries high voltage and must not be touched while in operation. The LG is an indispensable production aid for film processing, electronic manufacture, and precision mechanics. This device has also proven to be very reliable and efficient for the manufacture of measuring devices and control gears, for pcb assembly as well as for screen, pad printing and other printing procedures.

Number Of Flower : OPI   Inseparable HV-cable, attached permanently to the bar.

The "Liquid Super Separator" is a new concept of a pneumatic mist remover without filter element. The "Element Free Pneumatic Water Separator" uses a special centrifugal technique with "radial multi-nozzles" that is world patent pending and makes it possible to reject liquid mist (water and oil) to 99.9%! This pneumatic mist separator is virtually maintenance free, as there is no need to replace any filter element. A standard traditional filter with an element and automatic drain may be placed downstream to control micron size but the high liquid and mist removal of the separator will keep it clean and it may not require element replacement for an extended period of time. Maintains extremely low pressure drop FEATURES No filter element Minimal pressure drop Maintenance free Complete mist rejection Mist rejection rate : 99.99% Oil mist rejection rate : 99.99% Semi-permanent durability Power free Complete with Auto-drain No performance change over time Trouble free with simple construction Large capacity but compact Low cost 5 year warranty (except for auto drain)

Pneumatic Rotary Valves are a type of directional control valves which are used for control of pneumatic cylinders or as part of large pneumatic circuit, They are largely used for panel mounting applications.

pneumatic presses used in all types of industrial settings. Kjn enterprises manufacturing pneumatic presses for more than 25 years. Pneumatic presses common applications are: compacting, blanking, extruding, marking, cupping, peening, deep drawing, flaring, punching, rivetting, notching, cutting etc., india. pneumatic pressing tonnage:50 kg to 5 tonnestype of frame :c - frame, single pillar, 2 - pillar, 4 - pillar pneumatic conventional press, tandem press, impact press and toggle press. Our base plates are manufactured from prime-quality ms with the working surface ground and hard chrome plated for long rust-free life. base plate : our base plates are manufactured from prime-quality ms with the working surface ground and hard chrome plated for long rust-free life. Various base plate construction options are available. Please refer our questionnaire for the same. controls : pneumatic presses can be operated in many ways. It can be completely plc controlled or can be operated by a simple hand lever valve. Please refer our questionnaire for the various control options available. additional features : many additional features can be provided on the pneumatic presses for ease of operation, safety of the operator and better finish of the component being pneumatic presses. The various features that can be provided are listed in the questionnaire. Please refer our questionnaire for further information.

our standard range of pneumatic cylinders are available in bore sizes ranging from 6mm diameter to 350mm diameter with strokes starting from 15mm to 1000mm long. These pneumatic cylinders are made of hard chrome plated heavy duty seamless tubes, c.i. End covers, hard chrome plated en-8 piston rods and high quality neoprene/nitrile seals.

Number Of Flower : Panel Cooler

Material : Fiber, Metal, Plastic, Stainless Steel

Certification : CE Certified, ISO Certification

Application : Air Cooling, Water Cooling

Country of Origin : 110V, 220V, 380V, 440V

Condition : New, Used

Automatic Grade : Automatic, Fully Automatic

Total Carbohydrate : 1year, 2years, 6months

Simple and rugged design Pneumatic Valves these are available in sizes 1/4" to 1" BSP. They are used in applications where uni-directional flow is required.

When lubrication is required as well as cooling, lubricating mist can be reduced and cooling enhanced.Heavy coolant can be messy, costly and must be carefully maintained. Dry machining is not always possible due to the need for lubrication or additional cooling that cold air alone cannot provide. The unique patent pending low cost Frigid-X Sub-Zero Vortex Tool Cooling Mist System is ideal for these applications. The unit is comprised of a coolant/lubrication suction system which draws any water based liquid into a specially designed delivery system. This cools the liquid to deliver a very cold fluid "mist" at around 40 degrees F (5 degrees C). This cooling allows for as much as 20% less coolant needed, faster production rates and improved quality. An Adjusting screw controls the amount of mist required. Simple operation, no moving parts except for the adjusting screw means long life, low cost operation and zero maintenance. APPLICATIONS Solid Carbide End Mills Wherever lubrication is required in machining When cooling is required beyond the capability of cold air alone ADVANTAGES No electricity required - simplicity in design Low Cost Reduces coolant / lubricant cost by using less fluid Improves safety with less mist No moving parts except for an adjusting screw for the fluid Small and lightweight - portable Maintenance free operation

Cabinet Panel Cooler Accessories are available with a standard two-way normally closed solenoid valve and thermostat kit Model 90015 (120V) or Model 90016 (240V). This limits the flow of air only when required. The thermostat is factory set at 95°F (35°C) and will normally hold +/- 2°F (1°C) inside the enclosure. It is rated 24V-240V, 50/60Hz. Ul recognized and CSA approved. Thermostat And Solenoid Valve Kit This kit comes complete with a solenoid valve, thermostat, and a resistor. The resistor is included should you encounter rapid temperature fluctuations in the control panel causing the solenoid to cycle on and off to quickly (chattering). The resistor is installed (if needed) across the leads of the thermostat and prevents chattering by dampening the thermo switch sensitivity.