IndicationsPass - GREEN LED, LOW & High Fail - RED LED With Audible Alarm
Test ActuationBy Gently Pressing Metal Sensor Plate
Wrist strap is the first line of defence against electrostatic charges builds up on the human body. it is designed to carry away this charge as soon as it is generated. At the same time wrist strap must remain electrically safe for the user. Thus, it is important to test every wrist strap regularly. In order to protect the sensitive electronic components the maximum wrist strap resistance should not be more than 10 Meg ohms on the other end, the resistance should not be less than 0.75 Meg ohms as protection to the wearer from dangerous level of the voltage and current flow. The wrist strap tester checks these parameters under actual operating conditions with the strap on the wrist. It clearly indicates weather or not the resistance of the wrist strap system including the wearer is at least 0.75 Meg ohms and not more than 10 Meg ohms respectively.SPECIFICATIONS:Range : Wrist strap 0.75 to 10 Meg ohmIndications : Pass – GREEN LEDLOW & High fail – RED LED With Audible alarmTest actuation : By gently pressing metal sensor plateAccuracy : +/- 10%Power supply : 9 Volt BatteryLow battery : Warning at 7.0 VDimensions : 135 x 70 x 30 mmWeight : App. 150Gms with batteryCalibration : Recommended every 12 monthsWarranty : 12 MonthsOptional : Instruction Board, Carry Case & Door Locking System.
Wrist strap is the first line of defence against electrostatic charges builds up on the human body. it is designed to carry away this charge as soon as it is generated. At the same time wrist strap must remain electrically safe for the user. Thus, it is important to test every wrist strap regularly. In order to protect the sensitive electronic components the maximum wrist strap resistance should not be more than 10 Meg ohms on the other end, the resistance should not be less than 0.75 Meg ohms as protection to the wearer from dangerous level of the voltage and current flow. The wrist strap tester checks these parameters under actual operating conditions with the strap on the wrist. It clearly indicates weather or not the resistance of the wrist strap system including the wearer is at least 0.75 Meg ohms and not more than 10 Meg ohms respectively.SPECIFICATIONS:Range : Wrist strap 0.75 to 10 Meg ohmIndications : Pass – GREEN LEDLOW & High fail – RED LED With Audible alarmTest actuation : By gently pressing metal sensor plateAccuracy : +/- 10%Power supply : 9 Volt BatteryLow battery : Warning at 7.0 VDimensions : 135 x 70 x 30 mmWeight : App. 150Gms with batteryCalibration : Recommended every 12 monthsWarranty : 12 MonthsOptional : Instruction Board, Carry Case & Door Locking System.
IndicationsPass - GREEN LED, LOW & High Fail - RED LED (With Alarm)
Test ActuationBy Gently Pressing Metal Sensor Plate
Accuracy+/- 10%
Power Supply9 Volt Battery
Wrist Strap & ESD foot wears are the first line of defence against electrostatic charges build up on the human body.They are designed to carry away this charge as soon as it is generated. At the same time wrist strap/foot wear must remain electrically safe for the user. Thus, it is important to test every wrist strap / footwear regularly. In order to protect the sensitive electronic components the maximum wrist strap resistance should not more than 10 Meg ohms and foot wears resistance should not more than 100 Meg ohms. On the other end, the resistance should not be less than 0.75 Meg ohms as protection to the wearer from dangerous level of the voltage and current flow. The wrist strap and the footwear tester checks these parameters under actual operating conditions with the strap on the wrist or foot wear to the foot. It clearly indicates weather or not the resistance of the wrist strap/foot wear system including the wearer is at least 0.75 Meg ohms and not more than 10/100 Meg ohms respectively.SPECIFICATIONS:Range : Wrist strap 0.75 to 10 Meg ohmsFoot Wear 0.75 to 100 Meg ohmsRange Selection : By slide switchIndications : Pass – GREEN LEDLOW & High fail – RED LED (With Alarm)Test actuation : By gently pressing metal sensor plateAccuracy : +/- 10%Power supply : 9 Volt BatteryLow battery : Warning at 7.0 VDimensions : 135 x 70 x 30 mmWeight : App. 150Gms with battery
Wrist Strap & ESD foot wears are the first line of defence against electrostatic charges build up on the human body.They are designed to carry away this charge as soon as it is generated. At the same time wrist strap/foot wear must remain electrically safe for the user. Thus, it is important to test every wrist strap / footwear regularly. In order to protect the sensitive electronic components the maximum wrist strap resistance should not more than 10 Meg ohms and foot wears resistance should not more than 100 Meg ohms. On the other end, the resistance should not be less than 0.75 Meg ohms as protection to the wearer from dangerous level of the voltage and current flow. The wrist strap and the footwear tester checks these parameters under actual operating conditions with the strap on the wrist or foot wear to the foot. It clearly indicates weather or not the resistance of the wrist strap/foot wear system including the wearer is at least 0.75 Meg ohms and not more than 10/100 Meg ohms respectively.SPECIFICATIONS:Range : Wrist strap 0.75 to 10 Meg ohmsFoot Wear 0.75 to 100 Meg ohmsRange Selection : By slide switchIndications : Pass – GREEN LEDLOW & High fail – RED LED (With Alarm)Test actuation : By gently pressing metal sensor plateAccuracy : +/- 10%Power supply : 9 Volt BatteryLow battery : Warning at 7.0 VDimensions : 135 x 70 x 30 mmWeight : App. 150Gms with battery
FeaturesSimultaneous Measurement Of Right And Left Foot
The Wrist strap Cum Dual Footwear tester is a jig type arrangement to test the validity of ESD Wrist strap; Slippons and Shoes and Independent measurement is taken simultaneously wrist_strap_dual_footwear_testerof both right, left foot and wrist strap at the same time. Other Footwear testers can only measure two foot at a time, or the combined resistance of both foot. The wrist strap cum Dual Foot Tester reduces the testing time by half, and offers the operator a visual and audible measurement of Pass or fail of both foot and wrist strap before entering the EPA. Operation of Wrist Strap: Connect the wrist strap cord to the instrument with the strap on the wrist; press gently on the metal sensor of the instrument. The instrument comes on automatically when this is done. The operator can check whether the resistance of the wrist strap falls within the acceptable range (0.75 to 10 Meg ohms), This is indicated by green (pass) LED lighting up. Operation of foot wears: Simply stand on the two stainless steel footprints and push the press to test button. The instrument comes on automatically when this is done. The operator can check whether the resistance of the Foot wears falls within the acceptable range of 0.75 to 100 meg ohms, This is indicated by green (pass) LED lighting up.Specifications:Wrist Strap Range : 0.75 to 10 Meg OhmsFoot Wear Range : 0.75 to 100 Meg ohms
The Wrist strap Cum Dual Footwear tester is a jig type arrangement to test the validity of ESD Wrist strap; Slippons and Shoes and Independent measurement is taken simultaneously wrist_strap_dual_footwear_testerof both right, left foot and wrist strap at the same time. Other Footwear testers can only measure two foot at a time, or the combined resistance of both foot. The wrist strap cum Dual Foot Tester reduces the testing time by half, and offers the operator a visual and audible measurement of Pass or fail of both foot and wrist strap before entering the EPA. Operation of Wrist Strap: Connect the wrist strap cord to the instrument with the strap on the wrist; press gently on the metal sensor of the instrument. The instrument comes on automatically when this is done. The operator can check whether the resistance of the wrist strap falls within the acceptable range (0.75 to 10 Meg ohms), This is indicated by green (pass) LED lighting up. Operation of foot wears: Simply stand on the two stainless steel footprints and push the press to test button. The instrument comes on automatically when this is done. The operator can check whether the resistance of the Foot wears falls within the acceptable range of 0.75 to 100 meg ohms, This is indicated by green (pass) LED lighting up.Specifications:Wrist Strap Range : 0.75 to 10 Meg OhmsFoot Wear Range : 0.75 to 100 Meg ohms
Static Shielding Bags provide complete protection from electrostatic discharges. The material is constructed out of Polyester, Vacuum Deposited Aluminum and Polythene, coated with Static Dissipative Lacquer on both sides. The material is high on Optical Clarity and low on ionic contamination.
Static Shielding Bags provide complete protection from electrostatic discharges. The material is constructed out of Polyester, Vacuum Deposited Aluminum and Polythene, coated with Static Dissipative Lacquer on both sides. The material is high on Optical Clarity and low on ionic contamination.
ApplicationElimination Of Electrostatic Charge On Moving Surfaces
Power SourceHigh Voltage Power Source
PackagingStandard Packaging
DesignCompact And Rugged Design
The generation and accumulation of unwanted electrostatic charges especially on moving surfaces, poses a serious problem in various industries and processes. For example, static charges can lead to sticking and crumpling of polyester films while being processed on the machines. Collection of dust and other particulate contaminants on surfaces due to static is another example.These shock-less static discharge bars are designed for elimination of electrostatic charge on moving surfaces. The bar is powered by a high voltage power source. The design is compact, yet rugged and is a very effective static eliminating tool for most industrial applications.These AC static eliminating bars generate ions of both polarities, thereby ensuring effective static elimination of positive and negative charges from moving surfaces. Features – barShockless and hence no chance of hazard even if electrode is touchedElectrodes protected from short circuit; no damage even if accidentally earthedGood discharge range 10 – 40 mmRugged and reliableEasy installation and start-upNo maintenance, except for periodic cleaningStandard 2 meters HV interconnecting cableOptional: Adjustable mounting bracket
The generation and accumulation of unwanted electrostatic charges especially on moving surfaces, poses a serious problem in various industries and processes. For example, static charges can lead to sticking and crumpling of polyester films while being processed on the machines. Collection of dust and other particulate contaminants on surfaces due to static is another example.These shock-less static discharge bars are designed for elimination of electrostatic charge on moving surfaces. The bar is powered by a high voltage power source. The design is compact, yet rugged and is a very effective static eliminating tool for most industrial applications.These AC static eliminating bars generate ions of both polarities, thereby ensuring effective static elimination of positive and negative charges from moving surfaces. Features – barShockless and hence no chance of hazard even if electrode is touchedElectrodes protected from short circuit; no damage even if accidentally earthedGood discharge range 10 – 40 mmRugged and reliableEasy installation and start-upNo maintenance, except for periodic cleaningStandard 2 meters HV interconnecting cableOptional: Adjustable mounting bracket
Application : Elimination Of Electrostatic Charge On Moving Surfaces
MaterialTriple-layer Construction With Electrically Conductive Layer
ApplicationProtecting Electronic Components From Static Electricity
Common work surfaces made of wood, sun-mica generate static electricity very easily on friction. Covering these work surfaces with static dissipative mats ensures that all electronic components/ sub assemblies are safe while being handled, inspected or tested. Table Mats are of 3 layer construction. A conductive layer is buried in between outer static ws1dissipative layers.
Outer Layers Provide aesthetic appearance to a work environment protect components on a PCB from shorting while the sub assembly is being tested are easy to clean with any mild soap detergent.
Inner Conductive Layer Provides quick drainage of static charges to the ground These mats can be made available in various sizes.
Material Sheet of 2mm thickness, triple layer in construction. Electrically Conductive layer buried in between Static Dissipative layers.
Surface Resistivity of Static Dissipative layers = 5 x 105 to 108 ohms/sq
Surface Resistivity of Conductive layer < 5 x 104 ohms/sq
Common work surfaces made of wood, sun-mica generate static electricity very easily on friction. Covering these work surfaces with static dissipative mats ensures that all electronic components/ sub assemblies are safe while being handled, inspected or tested. Table Mats are of 3 layer construction. A conductive layer is buried in between outer static ws1dissipative layers.
Outer Layers Provide aesthetic appearance to a work environment protect components on a PCB from shorting while the sub assembly is being tested are easy to clean with any mild soap detergent.
Inner Conductive Layer Provides quick drainage of static charges to the ground These mats can be made available in various sizes.
Material Sheet of 2mm thickness, triple layer in construction. Electrically Conductive layer buried in between Static Dissipative layers.
Surface Resistivity of Static Dissipative layers = 5 x 105 to 108 ohms/sq
Surface Resistivity of Conductive layer < 5 x 104 ohms/sq
Brand Name : Marvel
Thickness : 2 Mm
Material : Triple-layer Construction With Electrically Conductive Layer
Application : Protecting Electronic Components From Static Electricity
Detection MethodCharge Coupling By Field Interception
Detection Sensitivity+/- >100V
Range SelectionAuto Ranging And Auto Resetting
IndicationLED Visual Indication With Audible Alarm
Power Supply9V Battery
The Static Alarm senses changes in electrostatic fields. The static alarm is ideal for scanning the electrostatic field in critical areas of production and testing of electronic circuit, plastic and textile industries.SPECIFICATIONS:Detection method : charge coupling by field InterceptionDetection sensitivity : +/- >100VRange selection : Auto ranging and auto resettingIndication : Prominent for LED visual Indication with Audible alarmPower supply : 9V BatteryDimensions : 135 x 70 x 30mmWeight : Approximately 135G (with battery)NOTE: The specifications mentioned in this datasheet are subject to change without prior notice due to our continuous program of product development. Buyer or User shall be responsible for deciding the suitability.
The Static Alarm senses changes in electrostatic fields. The static alarm is ideal for scanning the electrostatic field in critical areas of production and testing of electronic circuit, plastic and textile industries.SPECIFICATIONS:Detection method : charge coupling by field InterceptionDetection sensitivity : +/- >100VRange selection : Auto ranging and auto resettingIndication : Prominent for LED visual Indication with Audible alarmPower supply : 9V BatteryDimensions : 135 x 70 x 30mmWeight : Approximately 135G (with battery)NOTE: The specifications mentioned in this datasheet are subject to change without prior notice due to our continuous program of product development. Buyer or User shall be responsible for deciding the suitability.
Monitoring MethodCapacitive AC Pulse Principle For Wrist Strap
Monitoring Threshold10 Meg Ohms
ActivationAutomatic Activation When Plugged In
The Model WSM-01 has independent circuitry designed to continuously monitor the connections to ESD earth of Wrist strap & Work surface.WRIST STRAP: This section continuously monitors the wrist strap to detect loss of continuity between operator and monitor. Conditions such as broken coils cords and improper contact with the skin are detected instantly to alert the operator before serious and expensive ESD damage can occur. As there is no resistance return path from the wrist strap, it uses the ‘capacitive AC pulse principle’ to check if the operator is adequately grounded. The wrist strap section is automatically activated when it is plugged in. continuous monitoring reduces the need for periodic checks andalso ensures greater security. ESD WORK SURFACE: The work surface is monitored by a DC Resistive principle and a warning is given in case the surface to ground resistance exceeds the safe threshold value of 10 Meg ohms.
The Model WSM-01 has independent circuitry designed to continuously monitor the connections to ESD earth of Wrist strap & Work surface.WRIST STRAP: This section continuously monitors the wrist strap to detect loss of continuity between operator and monitor. Conditions such as broken coils cords and improper contact with the skin are detected instantly to alert the operator before serious and expensive ESD damage can occur. As there is no resistance return path from the wrist strap, it uses the ‘capacitive AC pulse principle’ to check if the operator is adequately grounded. The wrist strap section is automatically activated when it is plugged in. continuous monitoring reduces the need for periodic checks andalso ensures greater security. ESD WORK SURFACE: The work surface is monitored by a DC Resistive principle and a warning is given in case the surface to ground resistance exceeds the safe threshold value of 10 Meg ohms.
Application : Continuous Monitoring Of Wrist Strap
This instrument is designed to measure the Static Voltages carried on a human body. It is a good auditing tool to verify whether Personnel entering an ESD safe area are carrying any hazardous charges on themselves. It can also serve to verify whether all the ESD protection measures which have been taken to make a particular area ESD safe are effective. By such measures we mean conductive flooring, antistatic table mats, wrist straps, static sheilding bags, ionizing equipment, conductive containers and bins etc.It is very simple to use and only requires the personnel under test to touch the Button on the instrument and directly read the charge level in volts on the meter.
This instrument is designed to measure the Static Voltages carried on a human body. It is a good auditing tool to verify whether Personnel entering an ESD safe area are carrying any hazardous charges on themselves. It can also serve to verify whether all the ESD protection measures which have been taken to make a particular area ESD safe are effective. By such measures we mean conductive flooring, antistatic table mats, wrist straps, static sheilding bags, ionizing equipment, conductive containers and bins etc.It is very simple to use and only requires the personnel under test to touch the Button on the instrument and directly read the charge level in volts on the meter.
Usage/ApplicationMeasuring Surface Resistance And Resistance To Ground
Measurement Range LCD≤ 1X10E3 To ≥1X10E12 Ohms & Ohms/sq
Probe Voltage100V +/- 5%
The Surface Resistivity Meter measures both surface resistance and resistance to ground. This is meant for use in evaluating a wide variety of ESD protective materials including tablemats, floor mats, and hard ESD laminates. It measures and displays Surface Resistivity as well as surface to ground and point-to-point resistances. These measurements can be done in the range of 10E12 ohms by using two 2.5-kilo (5lb) heavy electrodes or through internal probes. To check whether surface Resistivity is in accordance with EOS/ESD Association standards S-4.1.SPECIFICATIONS:Measurement Range (LCD) : ≤ 1X10E3 to ≥1X10E12 ohms & ohms/sqMeasurement Range (LED) : < 10E3 to > 10E12 ohms & ohms/sqMeasurement accuracy (LCD) : 0.1 decadeMeasurement accuracy (LED) : 0.5 decadeProbe Voltage : 100V +/- 5%Battery indicator : Green when battery is fully charged
The Surface Resistivity Meter measures both surface resistance and resistance to ground. This is meant for use in evaluating a wide variety of ESD protective materials including tablemats, floor mats, and hard ESD laminates. It measures and displays Surface Resistivity as well as surface to ground and point-to-point resistances. These measurements can be done in the range of 10E12 ohms by using two 2.5-kilo (5lb) heavy electrodes or through internal probes. To check whether surface Resistivity is in accordance with EOS/ESD Association standards S-4.1.SPECIFICATIONS:Measurement Range (LCD) : ≤ 1X10E3 to ≥1X10E12 ohms & ohms/sqMeasurement Range (LED) : < 10E3 to > 10E12 ohms & ohms/sqMeasurement accuracy (LCD) : 0.1 decadeMeasurement accuracy (LED) : 0.5 decadeProbe Voltage : 100V +/- 5%Battery indicator : Green when battery is fully charged
Usage/Application : Measuring Surface Resistance And Resistance To Ground
Reliable on-the-spot measurement of static charges has been easier than with the portable SCM-01. Hand-held, yet highly accurate and low drift, the MPSCM-02 answers three basic questions:Is static present and on what Surfaces, Materials or people ?How much static?What is the polarity of the Charge ?The instrument is ideal for use in such static sensitive environment as electronic component production and assembly areas, clean rooms, computer, medical and R&D Laboratories, surgical rooms, medical device manufacturer, printing pres, packing and production lines, etc.SPECIFICATIONS:Measurement Range : +/- 10kV At 1 InchMeasurement Accuracy : +/- 10%Indication : 2 ½ Digit LCD DisplayTest actuation : Press TO readPower supply : 9 Volt BatteryLow battery : warning at 7.0 voltsCalibration : Recommended every 12 monthsDimensions : 135 x 70 x 30mmWeight : 180 GmsWarranty : 12 Months
Reliable on-the-spot measurement of static charges has been easier than with the portable SCM-01. Hand-held, yet highly accurate and low drift, the MPSCM-02 answers three basic questions:Is static present and on what Surfaces, Materials or people ?How much static?What is the polarity of the Charge ?The instrument is ideal for use in such static sensitive environment as electronic component production and assembly areas, clean rooms, computer, medical and R&D Laboratories, surgical rooms, medical device manufacturer, printing pres, packing and production lines, etc.SPECIFICATIONS:Measurement Range : +/- 10kV At 1 InchMeasurement Accuracy : +/- 10%Indication : 2 ½ Digit LCD DisplayTest actuation : Press TO readPower supply : 9 Volt BatteryLow battery : warning at 7.0 voltsCalibration : Recommended every 12 monthsDimensions : 135 x 70 x 30mmWeight : 180 GmsWarranty : 12 Months
Conductive Trays with risers help to organise items in a static safe area. Tools, Components, Documents can be stored easily while providing sensitive components safety from electrostatic discharges.
Conductive Trays with risers help to organise items in a static safe area. Tools, Components, Documents can be stored easily while providing sensitive components safety from electrostatic discharges.
ApplicationCarrying Tools In Static Sensitive Environments
SizeStandard Sizes Available
Ideal ForVisiting Engineers
Safety FeaturesSafe For Static Sensitive Environments
Conductive Tool Boxes are ideal for visiting engineers. The Surface resistivity of the boxes is in the conductive range i.e. < 106 ohms/sq. The tool box can be used to carry tools and is safe enough to be placed in Static sensitive environments.
Conductive Tool Boxes are ideal for visiting engineers. The Surface resistivity of the boxes is in the conductive range i.e. < 106 ohms/sq. The tool box can be used to carry tools and is safe enough to be placed in Static sensitive environments.
Application : Carrying Tools In Static Sensitive Environments
ApplicationStorage And Transportation Of Sensitive Components
FeatureStackable,Heavy Duty Re-inforced Base And Stacking Rim
PackagingBulk Packaging
Conductive Bins offer complete safety for sensistive components while being stored or carried in-house. The surface resistance of these bins is less than 106.StackableHeavy Duty Re-inforced base and stacking rimSlot for identification card holdersEasy access to contents
Conductive Bins offer complete safety for sensistive components while being stored or carried in-house. The surface resistance of these bins is less than 106.StackableHeavy Duty Re-inforced base and stacking rimSlot for identification card holdersEasy access to contents
Application : Storage And Transportation Of Sensitive Components
Feature : Stackable,Heavy Duty Re-inforced Base And Stacking Rim
Removes any static on the body. This mat can be cut to fit the desk or floor space.
Easy setting
Can be used in high temperature and low temperature environments
No pollution by bleeding anti-static material in the rubber.
Very durable, it withstands cracks and curling
Dimensions : 2mm thick x 1m wide
Floor Mat Installation Procedure:
A clean level surface is required for installation of floor mats. Plaster of paris may be used to level the floor surface.
Copper Strips are used to create a mesh grid on the floor to ensure that the floor mats are completely interconnected. The copper grids are in turn connected to the earth through a cord. Adhesives are used to stick the copper strips to the floor.
The Floor Mats are then laid over the copper grids.
All intersections (close to the edges) of Copper Strips are rivetted to the Floor Mat, ensuring contact with the conductive layer.
Removes any static on the body. This mat can be cut to fit the desk or floor space.
Easy setting
Can be used in high temperature and low temperature environments
No pollution by bleeding anti-static material in the rubber.
Very durable, it withstands cracks and curling
Dimensions : 2mm thick x 1m wide
Floor Mat Installation Procedure:
A clean level surface is required for installation of floor mats. Plaster of paris may be used to level the floor surface.
Copper Strips are used to create a mesh grid on the floor to ensure that the floor mats are completely interconnected. The copper grids are in turn connected to the earth through a cord. Adhesives are used to stick the copper strips to the floor.
The Floor Mats are then laid over the copper grids.
All intersections (close to the edges) of Copper Strips are rivetted to the Floor Mat, ensuring contact with the conductive layer.
ApplicationStorage Of Electrostatic Sensitive Devices
Size400mm X 250mm X 160mm,150mm X 75mm X 35mm
PackagingCabinet With Drawers
Conductive Component Organiser provides systematic storage of electrostatic sensitive devices. It consists of a cabinet with 25 small drawers.Size of Cabinet: 400mm x 250mm x 160mmSize of the Drawers: 150mm x 75mm x 35mm
Conductive Component Organiser provides systematic storage of electrostatic sensitive devices. It consists of a cabinet with 25 small drawers.Size of Cabinet: 400mm x 250mm x 160mmSize of the Drawers: 150mm x 75mm x 35mm
Material : Conductive Material
Application : Storage Of Electrostatic Sensitive Devices
Conductive Boxes provide protection to sensitive Components from electrostatic discharges while being stored or transported. Surface Resistivity of the material is less than 106 ohms/sq.
Conductive Boxes provide protection to sensitive Components from electrostatic discharges while being stored or transported. Surface Resistivity of the material is less than 106 ohms/sq.
Easily mounts under the bench surface and offers 2 banana 4mm socket a single grounding cord from the bench mount connects both banana sockets to thebenchmount-copy earth. Each of the banana socket can be used to terminate ground cords of either table mats or wrist straps. Each operator working on a long table can be provided a bench mount socket for easy and convenient ground connection
Easily mounts under the bench surface and offers 2 banana 4mm socket a single grounding cord from the bench mount connects both banana sockets to thebenchmount-copy earth. Each of the banana socket can be used to terminate ground cords of either table mats or wrist straps. Each operator working on a long table can be provided a bench mount socket for easy and convenient ground connection
This product has an inner layer made of soft conductive rubber which ensures 100% efficient conductive contact with the skin of the user. The hook and the loop fasteners facilitate adjustment to the size of the wrist while maintaining comfort for working long hours. This wrist strap is very rugged in construction. A coiled ground is provided with each wrist strap. The cord carries 1 megaohm resistor in series, moulded into the snap female connectors. Various end connectors are offered to suit requirements
This product has an inner layer made of soft conductive rubber which ensures 100% efficient conductive contact with the skin of the user. The hook and the loop fasteners facilitate adjustment to the size of the wrist while maintaining comfort for working long hours. This wrist strap is very rugged in construction. A coiled ground is provided with each wrist strap. The cord carries 1 megaohm resistor in series, moulded into the snap female connectors. Various end connectors are offered to suit requirements
About us packaging manufacturer (Marvel Products) focused on corrugated boxes and tapes; a Jamnagar-based manufacturer of precision components for automotive, electrical, and sanitary industries (Marvel Products) founded in 1989; and a leader in window furnishings (Marvel Blinds) offering a wide range of blinds, operating systems, and fabrics. Additionally, there is a well-known American brand of refrigeration equipment (Marvel Commercial Refrigeration) that has been in business since 1892.
Reviews & Ratings
Write a Review
Post Free Ad