GN 813 vertical acting toggle clamps are used for applications where a very high holding force is required such as closing of foam molds. These clamps have been designed for easy dismantling: i.e. the bearing pins are locked with circlips. After dismantling the individual parts, they can be modified to suit individual applications.
GN 813 vertical acting toggle clamps are used for applications where a very high holding force is required such as closing of foam molds. These clamps have been designed for easy dismantling: i.e. the bearing pins are locked with circlips. After dismantling the individual parts, they can be modified to suit individual applications.
The two end-cap parts have some reference pins which are housed in special counter-seats. Two cavities inside the end-cap are provided for housing two hexagonal nuts DIN 934. Thanks to the tapered shape of the cavity, the end-cap exerts a pressure on the inner walls of the tube, due to the tightening of the nuts, thus ensuring the tensile strength of the connection. The level of the tensile strength depends on the tube dimensional tolerances, the condition of the tube inner surfaces and the tightening torque applied.
The two end-cap parts have some reference pins which are housed in special counter-seats. Two cavities inside the end-cap are provided for housing two hexagonal nuts DIN 934. Thanks to the tapered shape of the cavity, the end-cap exerts a pressure on the inner walls of the tube, due to the tightening of the nuts, thus ensuring the tensile strength of the connection. The level of the tensile strength depends on the tube dimensional tolerances, the condition of the tube inner surfaces and the tightening torque applied.
Glass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish. Brass boss, threaded pass-through hole. The ergonomic seven-lobe shape allows an effective grip to the operator when tightening. Suitable for axial locking; it can be used as a nut.
Glass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish. Brass boss, threaded pass-through hole. The ergonomic seven-lobe shape allows an effective grip to the operator when tightening. Suitable for axial locking; it can be used as a nut.
The clamping bore of GN 275 swivel clamp connectors is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462 respectively. The standard version of the clamping screw is a socket cap screw with hexagonal socket DIN 912. It can be replaced by a clamping kit GN 911 (article code see table of dimensions). GN 275 swivel clamp connectors can be assembled with swivel clamp connectors GN 271, GN 273 or GN 277 to create swivel clamp connector joints.
The clamping bore of GN 275 swivel clamp connectors is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462 respectively. The standard version of the clamping screw is a socket cap screw with hexagonal socket DIN 912. It can be replaced by a clamping kit GN 911 (article code see table of dimensions). GN 275 swivel clamp connectors can be assembled with swivel clamp connectors GN 271, GN 273 or GN 277 to create swivel clamp connector joints.
Indexing plungers with Stainless Steel-Plunger GN 608.5 are distinguished for their small dimensions. Pin Stainless Steel AISI 303 chemically nickel plated Single components Stainless Steel.
Indexing plungers with Stainless Steel-Plunger GN 608.5 are distinguished for their small dimensions. Pin Stainless Steel AISI 303 chemically nickel plated Single components Stainless Steel.
The special features of Stainless Steel-Cabinet „U“ handles GN 565.5 are their rigidity and ergonomical shaping. Stainless Steel-Cabinet „U“ handles (Type A) are produced from profiled extrusions. The manufacturing process (bending) allows the production of special lengths in relatively small quantities.
The special features of Stainless Steel-Cabinet „U“ handles GN 565.5 are their rigidity and ergonomical shaping. Stainless Steel-Cabinet „U“ handles (Type A) are produced from profiled extrusions. The manufacturing process (bending) allows the production of special lengths in relatively small quantities.
The thread locking PRB (polyamide allround coating) is a clamping lock which prevents the locking screw from being inadvertently being loosened and becoming detached.
The thread locking PRB (polyamide allround coating) is a clamping lock which prevents the locking screw from being inadvertently being loosened and becoming detached.
Stainless Steel-Hinges GN 129.5 are used for doors which are flush with the frame on the outside. Once assembled, they cannot be unhinged. With the fixing from the inside, they are especially suitable for doors and trap doors which must not be detachable from the outside as an anti-tamper device.
Stainless Steel-Hinges GN 129.5 are used for doors which are flush with the frame on the outside. Once assembled, they cannot be unhinged. With the fixing from the inside, they are especially suitable for doors and trap doors which must not be detachable from the outside as an anti-tamper device.
Spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is recommended. Due to different production methods, the dimensions l2 and l3 are different.
Spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is recommended. Due to different production methods, the dimensions l2 and l3 are different.
Glass-fibre reinforced polyamide based (PA) technopolymer. Spacer base (code CE.83950), designed for UNI 10227 self-tapping screws Ø 2.2 (not included in the supply).
Glass-fibre reinforced polyamide based (PA) technopolymer. Spacer base (code CE.83950), designed for UNI 10227 self-tapping screws Ø 2.2 (not included in the supply).
Sheet metal hinges GN 136 are low-cost designs for low-load applications. without bores, for welding (only in Stainless Steel NI), with bores for cylinder head screws lens head screws, with bore, for countersunk screws.
Sheet metal hinges GN 136 are low-cost designs for low-load applications. without bores, for welding (only in Stainless Steel NI), with bores for cylinder head screws lens head screws, with bore, for countersunk screws.
Mould-on polyurethane, hardness 95 Shore A. hub directly made into the centre. The wheel hub is designed to be easily reprocessed to obtain a keyway or housing for clamping. Any further reprocesses on the wheel must be carried out with maximum working temperature up to 80°C, (recommended max limit temperature during normal use of the product) to prevent degradation of the polyurethane coating.Ideal solution for equipment with drive wheels. hub with ball bearings. Ideal solution for heavy loads and continuous moving.
Mould-on polyurethane, hardness 95 Shore A. hub directly made into the centre. The wheel hub is designed to be easily reprocessed to obtain a keyway or housing for clamping. Any further reprocesses on the wheel must be carried out with maximum working temperature up to 80°C, (recommended max limit temperature during normal use of the product) to prevent degradation of the polyurethane coating.Ideal solution for equipment with drive wheels. hub with ball bearings. Ideal solution for heavy loads and continuous moving.
Suitable for use in environments with the presence of atmospheric agents, alcohols and glycols; use in environments with the presence of organic and mineral acids, basic solutions and saturated vapour is not recommended. The diagram shows the force to be applied to a wheel to keep it moving at the constant speed of 4 kmh, according to the applied load. The intersection point with a 50N value is the maximum transportable load with a manually actuated 4-wheel trolley; in fact, 200N = 50N x 4 wheels is the maximum force that may be supported by the operator according to the regulations in force regarding work safety.
Suitable for use in environments with the presence of atmospheric agents, alcohols and glycols; use in environments with the presence of organic and mineral acids, basic solutions and saturated vapour is not recommended. The diagram shows the force to be applied to a wheel to keep it moving at the constant speed of 4 kmh, according to the applied load. The intersection point with a 50N value is the maximum transportable load with a manually actuated 4-wheel trolley; in fact, 200N = 50N x 4 wheels is the maximum force that may be supported by the operator according to the regulations in force regarding work safety.
Spring plungers GN 614.5 are used as detents as well as for push-on and push-off applications and ejectors. The geometric shape of the plastic housing generates a self-clamping function which compensates drill hole tolerances of as much as 0.2 mm. It also allows the hand-tightened assembly and makes overhead installation easier.
Spring plungers GN 614.5 are used as detents as well as for push-on and push-off applications and ejectors. The geometric shape of the plastic housing generates a self-clamping function which compensates drill hole tolerances of as much as 0.2 mm. It also allows the hand-tightened assembly and makes overhead installation easier.
These sheet metal punches GN 123 allow the operator to punch in a simple way fixing holes in sheet metal doors for latches with square V14 and V20. Sheet metal punches GN 123 are ideally suited for punching holes into sheet metal up to 2 mm thickness.
These sheet metal punches GN 123 allow the operator to punch in a simple way fixing holes in sheet metal doors for latches with square V14 and V20. Sheet metal punches GN 123 are ideally suited for punching holes into sheet metal up to 2 mm thickness.
The lifting (F1) and pull out (F2) resistance values reported in the table are the result of tests carried out in the laboratory with handles assembled on metal sheet panels with thickness = 1.5 mm. Glass-fibre reinforced polyamide based (PA) technopolymer, grey-black colour, matte finish. Nickel-plated brass or polyamide based (PA) technopolymer.
The lifting (F1) and pull out (F2) resistance values reported in the table are the result of tests carried out in the laboratory with handles assembled on metal sheet panels with thickness = 1.5 mm. Glass-fibre reinforced polyamide based (PA) technopolymer, grey-black colour, matte finish. Nickel-plated brass or polyamide based (PA) technopolymer.
It's the user's responsibility to determine whether the product is suitable for the intended purpose according to the actual conditions of use. Polyamide based (PA) technopolymer with adjusting hexagon, black colour, matte finish.
It's the user's responsibility to determine whether the product is suitable for the intended purpose according to the actual conditions of use. Polyamide based (PA) technopolymer with adjusting hexagon, black colour, matte finish.
Hook clamps in unplated steel. Catch brackets in different shapes and finishes. hook clamp with padlock hole. hook clamp with security stop and technopolymer push button in RAL 3000 red colour or with stainless steel spring.
Hook clamps in unplated steel. Catch brackets in different shapes and finishes. hook clamp with padlock hole. hook clamp with security stop and technopolymer push button in RAL 3000 red colour or with stainless steel spring.
Reviews & Ratings
Write a Review
Post Free Ad