Variable Auto Transformer / Variac / Dimmerstat Dealers

Automation Electric Company is leading manufacturer of Custom made variac. This product is manufactured by utilizing fine quality material and advanced technology to meet industry needs. These custom made variac is designed as per user requirement with Input-Output function. Offered products are used in various applications. It can be tailored as per customer design. We offer this Custom made variac at a very nominal rate to our customers. Key Features Easy installation High quality Rugged construction Less maintenance cost Noise free operation Cost effective

  Variable Auto Transformer will be having round Toroidal Core made from CRGO Lamination duly annealed to reduce the iron Losses and for the good regulation as voltage drop on load is low due to low resistance of conductor & low leakage flux of toroidal core. Toroidal core will provide stepless, beakless, smooth continuous control linearly proportional to angular rotation. Toroidal core is having high efficiency as no load and full load losses are very low and negligible wave from and power factor distortion due to simple transformer action and excellent short time overload capacity. As Toroidal core is having no sharp edge the breakage of insulation and copper wire can be prevented. the toroidal is wound from metal tape wound on to a mandrel under closely controlled tension, then annealed and treated to develop fully the required magnetic characteristic. It has low electrical resistively, no hysteresis loss, a completely linear B-H Curve and an infinitely high saturation points. this permits the easiest direction of magnetization to be utilized.    

Advantages : Continuous, Step less and Break Less Voltage variation Negligible waveform & Power factor distortion Short Time Overload Capacity Renote operation possible SPECIFICATIONS Load Capacities 28 amps to 600 Amps in Single • and 28 Amps to 1000 Amps in Three • 28 Amps, 40 Amps, 60 Amps, 100 Amps, 200 Amps, 400 Amps, 600 Amps, 800 Amps, 1000 Amps ) Phase Single • and Three • Toroidal Coils with CRGO Steel Sheet Core Frequency 50 60 Hz. Voltage Variation Capability 0 - 270 V A.C in Single • and 0 - 470 in Three • Cooling Method AN for 28 Amps in Single• and Three • Oil Cooled for 40 Amps to 600 Amps in Single • Oil Cooled for 40 Amps to 1000 Amps in Three • Drive Mechanism Hand Driven with Knob Motor Operated with Step Syncronised Motor Compliance to test Standards IS 5142. Oil Confirming to IS 335 Copper Conductors Compliant to IS 13730 - 34 BASIC FEATURES Open Type for Panel Mounting Portable Type for Table Mounting M.S. Tank with Oil Immersed and Pressed Steel Radiators. Double varnished Toroidal Coils. Voltage Indicator Dial. Knob or Wheel for Voltage Variation Connector Plate or Bus Bars in cable box. High Quality Carbon Brushes.

 We are instrumental in offering the finest quality of Variable Auto Transformers at nominal rates on the market. Being the leading manufacturers and suppliers of Variable Auto Transformers, we process the Variable Auto Transformers using cutting-edge technology and latest machinery. The Variable Auto Transformers are quality-tested, and can be purchased in various specifications. The major selling point of the Variable Auto Transformers is that they have a sturdy construction, and made up of Crgo Core, Copper, and Alloy. Not only are these Variable Auto Transformers easy to install, and durable, they promise noise-free operation and low maintenance cost. The Variable Auto Transformers can be availed at Rs. 40,000/piece, and we are based in Delhi, India.   Build : Sturdy, durable Installation Process : easy, hassle-free, convenient Material : Crgo Core, Copper, Aloy Durability : Highly durable, damage-resistant   Features : Easy to install Low maintenance needs Durable Noise-free operation

Our packing system is systematized in such a manner that we can handle even bulk packaging with ease. Moreover, our packing experts take care of the customized as well as standard packing demands of the clients. With the aid of our smart logistics network, we can easily furnish quick and massive requirements of the buyers

We are manufacturer and exporter of continuously variable Auto Transformers, Variacs and Dimmer stat which operates on a nominal voltage of 240 V A.C & can give output voltage anywhere between 0 – 270 V, by a simple transformer action. The basic Auto Transformer is meant for operation off a nominal voltage of 240 V A.C & can give output voltage anywhere between 0 – 240 V or up to 270 V, by a simple transformer action. Three such Variable Auto transformer when connected electrically in star & mechanically in tandem, became suitable for operations of 415 V 3 Phase A.C. supply & to give output of 0 – 415 V or up to 470 V. Variacs or variable auto transformer is a continuously variable voltage transformer, having a single layer winding on a toroidal core of high grade Steel. In an autotransformer portions of the same winding act as both the primary and secondary winding. the winding has at least three taps where electrical connections are made. One end of the winding is usually connected in common to both the voltage source and the electrical load. The other end of the source and load are connected to taps along the winding. Different taps on the winding correspond to different voltages, measured from the common end. On one face of the copped winding, along the periphery, a special durable contact surface is made. A specially designed carbon brush slides smoothly on the surface. A contact arm holding the contact brush is fitted to the central shaft and as the control knob is rotated, the carbon brush slides over the winding and taps off a portion of voltage across the winding. Any desired voltage within the maximum range can be obtained by adjusting the position of the brush. The calibrated dial reads approximately the output voltage at no-load, when the input is at its rated value. Rotation of the brush arm by manual of motor drive delivers an output voltage from zero to or above line voltage. Variable Auto Transformer, manufactured by EnergX is the most useful and effective device for step less, break less and continuous control of A.C voltage and therefore, for control of various other parameters, dependent on A.C voltage. It is ideal controlling device for numerous applications in laboratories and in industrial & commercial fields.

Listed amidst the renowned Suppliers of Variable Autotransformer, we successfully deliver the finest range of products the clients. The wide assortments of products we offer are strictly as per the globally accepted norms.

Standard models include input voltages from 120VAC to 480VAC. Frequencies to 2000 Hz can be accommodated. Special units for voltages to 1000 VAC are available.

VARIAC is a continuous Variable AutoTransformer, having a single layer winding on a Toroidal Core( Donut-Shaped )  CRGO Stamping (  high-grade Cold Rolled Grain Oriented  steel). On one side of the copper winding, a special durable contact surface is made.  A contact holder arm  with specially selected high grade carbon brushes  slides smoothly on this surface over the winding and taps of a portion of voltage across the winding. Any desired voltage within the Maximum range can be obtained by adjusting the position of the Brush.   High grade CRGO stamping is used for making Variac Coils. Purity of copper is 99.99% used for winding the Variac coils. Very smooth & step less voltage control. Easy Installation & Connections. Temperature remains low. Virtually maintenance free High grade carbon brushes are used Wide range of current rating 4 Amp. To 1250 Amp. High Efficiency Power factor distortion & wave form is negligible. Simple rugged designing. Overloading capacity for a short time. Long functional Life assured. Spare carbon brushes provided for select ratings. Impeccable quality.   Servo Voltage Stabilizers Rectifiers Testing Instruments. Labs & Hotels Battery Chargers

We specialize in the manufacture of high current rated coils. The commutator surface of our coils is machine processed and hence very uniform and smooth. This is very important for proper collection of current by the carbon brushes thus reducing the heat generated. Our standard coils are 100 Amp, 150 Amp, 200 Amp. Using these coils we manufacture oil-cooled variautos from 100 Amp 3 Ph to 1200 Amp 3 Ph capacity (415 V input and 0-470 V variable output). In high current rated models we use multiple coils with properly rated balancing coils to achieve the rated current. Based on the calculations of cooling area appropriate no. of radiators &fins  are used. These variautos are generally motorized with geared mechanism. We also cater to tailor-made requirements.