Laboratory Analyzer Dealers

We are offering battery analyzer(rejenuator). This amazing product will help you revoke the battery to its life if it has gone bad before its expected life. Good for a 12v battery with ah capacity ranging from 100 ah to 200 ah. Battery dealers, extensive battery users, communication complexes, military establishments, forklift users can enjoy the benefits of our product and save a lot of recurring cost on batteries.

We offer the best quality Conductivity Analyzer in the market. Our Water Conductivity Analyzer is highly advanced and is used to give measurement of contamination of water / steam with any kind of salts. We are one of the chief Steam Conductivity Analyzer Manufacturers in Pune, Maharashtra. Benefits Calibration methods to optimize sensor responseFully programmable cell constantTemperature measurement with Pt 100 / Pt 100Non-linear for ultra pure waterFreely programmable for concentration For the Hach Ultra 9125 a variety of display units for choice: conductivity (S, μS, mS, per m or cm), resistivity (Ω, k Ω, mΩ, Ω per m or cm) and concentration (% or g/l) 2 calibration methods to optimize sensor response -1 or 2 points, electrical or processFully programmable cell constantPre-programmed for HCl and NaClFixed programmable coefficient in %/°C or in %/°FNon temperature compensation to conform to USP24 pharmaceutical regulations9125 offers a service menu with sensor polarization test and cable capacity measurementTotal galvanic isolation between sensors and the transmitter, between the micro-processors and other circuitry boards (analog outputs) to avoid electrical interferencesHACH ULTRA 9125 has pre-programmed concentration curves for HCl,HNO3, H2SO4, NaOH and NaClBuilt-in real time clock allows perfect data retrieval for quality control management and traceability: date, values of last calibration and self-diagnosis data Applications To monitor the presence or concentrations of salts in all type of waterDemineralization processTo detect the loss of efficiency of the resins (anion & cation)To monitor the quality of the ultrapure water produced right at the final outlet of the mixed bedPure waterSpecific non linear algorithms for temperature compensation in such water qualityConductivity is either measured directly (specific conductivity) or after cation exchanger (cationic conductivity)Reverse osmosis processto decide regeneration of cation / anion / mix bed and to maintain high process efficiencyTo monitor the concentrations of binary solutions of a chemical and water such as regeneration solutions for demineralization resins

We all know that now a days almost all vehicles are equipped with battery. After charging the battery it is very essential to check whether the battery is fully charged or not. Checking the gravity by hydrometer is half checking, to check the A.H. capacity it is necessary to test the battery on load. To achieve this the tester is suitable to test 12V 2.5 AH and 12 5A H. battery. This is load tester which tests battery voltage on load condition. By using this tester you can check the battery thoroughly on test bench as well as on vehicle.

Model 2020 Thermal Conductivity Analyzer is a versatile, explosion-proof, microprocessor-based instrument for measuring binary mixtures of gases. Model 2020 responds to the differences in thermal conductivity between various gases by continuously comparing the sample gas with a reference gas of known thermal conductivity.   Features • Customer selectable gas constituents; 11 gases, 110 combinations• 6 gas concentration alarm set points• Automatic linearization• Auto Ranging automatically selects the proper preset range for a given measurement. Manual override allows the user to lock onto a specific range of interest.• A 2-line alphanumeric display screen (VFD), driven by microprocessor electronics that continuously prompt and inform the operator• Proven sensor cell design• Auto and remote zero cal capabilities• ndependent zero and span correction• Two programmable alarm relays and a system failure alarm• Two way RS-232 serial digital port for use with a computer or other digitalcommunication device• Four analog outputs: two for measurement (0-1VDC and isolated 4-20mADC) and two for range identification• Extensive self-diagnostic testing at start-up and on demand with continuous power supply monitoring

Conductivity Analyzer, Absorption Analyze

Conductivity Analyzer, Table Top PH Meter Microprocesso

Conductivity Analyzer, Chlorine Analyzer, Conductivity Controlle

Laboratory Analyzer, Ohaus MB25 & MB27 Moisture Analyze

Ion Analyzer, Sheet Metal Laser Cutting, Precision Centerless Grindin

Thermal Conductivity Analyzer, Hydrocarbon Analyzers, Fluorescence Analyze