Single End Abrasive Belt Grinders manufactured at Amber are direct motor drive belt grinders which have extended and threaded shaft on which the serrated contact rubber wheel can be directly mounted and the attachments for mounting, tensioning and resting the belt can be mounted on the motor side cover. The direct drive motors attached to these belt grinders are of lower HP as the load is only single sided. The belt tensioning arm can be tilted easily from 0 to 90 degrees as per the application. The rotary ON – OFF Switch is directly mounted on the connecting box of the motor. This single end belt grinder can also be mounted on the tool post of a conventional lathe. Belt tensioning can easily be done by just pulling down the handle which is loaded on a spring. A belt adjusting knob helps to easily adjust the belt on the wheel. A serrated contact rubber wheel behind the abrasive belt helps to effortlessly ground and finish castings, forgings, hardware, kitchenware, metal fabricated parts, plastic parts, glass edges, etc. Other than standard single end belt grinders Amber can also manufacture customized belt grinders suitable for any particular application.
Single End Abrasive Belt Grinders manufactured at Amber are direct motor drive belt grinders which have extended and threaded shaft on which the serrated contact rubber wheel can be directly mounted and the attachments for mounting, tensioning and resting the belt can be mounted on the motor side cover. The direct drive motors attached to these belt grinders are of lower HP as the load is only single sided. The belt tensioning arm can be tilted easily from 0 to 90 degrees as per the application. The rotary ON – OFF Switch is directly mounted on the connecting box of the motor. This single end belt grinder can also be mounted on the tool post of a conventional lathe. Belt tensioning can easily be done by just pulling down the handle which is loaded on a spring. A belt adjusting knob helps to easily adjust the belt on the wheel. A serrated contact rubber wheel behind the abrasive belt helps to effortlessly ground and finish castings, forgings, hardware, kitchenware, metal fabricated parts, plastic parts, glass edges, etc. Other than standard single end belt grinders Amber can also manufacture customized belt grinders suitable for any particular application.
IE 2 Motors (AN Series) manufactured by Amber are High Efficiency Motors satisfying the IE2 Efficiency Level as mentioned in IEC 60034 – 1. All AN Series motors ranging from 63 to 200L are manufactured and tested inhouse. These motors have robust Cast Iron Enclosure and are even light in weight than conventional motors. IE2 Amber motors are assembled with high quality CRNO magnetic thin lamination sheets and EN8 material grounded shafts. Rotors of these motors are dynamically balanced to ensure vibration free working as well as decrease chances of maintenance and give a longer life to the motor. These motors are wounded with modified polyester enameled copper wire (IS 13730, Part 03, Thermal Class 155°C) and insulation is Class F with permissible temperature rise limited to Class B which allows 25°C reserve thermal capacity. Bearings used in these motors being appropriately lubricated double sealed make sure that there are no frictions generated which may electrically as well as mechanically harm the motor. In AN Series (90 to 132M Frame) motors there is major flexibility of mounting the connection box on any of the three sides on request.
IE 2 Motors (AN Series) manufactured by Amber are High Efficiency Motors satisfying the IE2 Efficiency Level as mentioned in IEC 60034 – 1. All AN Series motors ranging from 63 to 200L are manufactured and tested inhouse. These motors have robust Cast Iron Enclosure and are even light in weight than conventional motors. IE2 Amber motors are assembled with high quality CRNO magnetic thin lamination sheets and EN8 material grounded shafts. Rotors of these motors are dynamically balanced to ensure vibration free working as well as decrease chances of maintenance and give a longer life to the motor. These motors are wounded with modified polyester enameled copper wire (IS 13730, Part 03, Thermal Class 155°C) and insulation is Class F with permissible temperature rise limited to Class B which allows 25°C reserve thermal capacity. Bearings used in these motors being appropriately lubricated double sealed make sure that there are no frictions generated which may electrically as well as mechanically harm the motor. In AN Series (90 to 132M Frame) motors there is major flexibility of mounting the connection box on any of the three sides on request.
Supply Voltage:415, 380, 220 or as per requirement
Supply Frequency50 Hz, 60 Hz or as per requirement
Poles2 & 4
InsulationF Class
Flexible Shaft Grinder is a combination of a Flexible Shaft consisting of a rotating wire rope or coil (known as Inner core) which is flexible but has some torsion stiffness, and an Induction Electric High Speed Motor mounted on a swivelling stand. Flexible shaft is constructed with a number of superimposed, tightly wound, helical coils spring wrapped around a centre wire due to which it can be bent, without fracture, to a much smaller radius than a solid shaft of the same outside diameter. When the motor is switched on considerable power is transmitted with negligible friction to the end of the flexible shaft where a grinding, cutting or buffing wheel is attached. The biggest benefit of Flexible shaft grinder is its possibility to operate in restricted areas at constant speed. Thus Flexible shaft grinding is the most appropriate method to grind or polish heavy unmovable or heavy to handle jobs there by giving freedom to the operator to grind the job without handling it. Flexible Shaft Grinders manufactured at Amber are continuous duty rating, easy to operate, robust constructed, vibration free and low maintenance as a result of which high productivity is achieved at lowest consumption of power.
Flexible Shaft Grinder is a combination of a Flexible Shaft consisting of a rotating wire rope or coil (known as Inner core) which is flexible but has some torsion stiffness, and an Induction Electric High Speed Motor mounted on a swivelling stand. Flexible shaft is constructed with a number of superimposed, tightly wound, helical coils spring wrapped around a centre wire due to which it can be bent, without fracture, to a much smaller radius than a solid shaft of the same outside diameter. When the motor is switched on considerable power is transmitted with negligible friction to the end of the flexible shaft where a grinding, cutting or buffing wheel is attached. The biggest benefit of Flexible shaft grinder is its possibility to operate in restricted areas at constant speed. Thus Flexible shaft grinding is the most appropriate method to grind or polish heavy unmovable or heavy to handle jobs there by giving freedom to the operator to grind the job without handling it. Flexible Shaft Grinders manufactured at Amber are continuous duty rating, easy to operate, robust constructed, vibration free and low maintenance as a result of which high productivity is achieved at lowest consumption of power.
Amber manufactures Double End Abrasive Belt Grinders which accommodates a direct drive motor and serrated contact rubber wheels at both the ends of the motor and the attachments for mounting, tensioning and resting the belt are mounted on the motor side cover. The belt tensioning arm can be tilted easily from 0 to 90 degrees as per the application. A rotary ON – OFF Switch is mounted on the motor base. A fabricated or Cast Iron pedestal stand can be provided on special request. Belt tensioning can easily be done by just pulling down the handle which is loaded on a spring.A belt adjusting knob helps to easily adjust the belt on the wheel. A serrated contact rubber wheel behind the abrasive belt helps to effortlessly ground and finish castings, forgings, hardware, kitchenware, metal fabricated parts, plastic parts, glass edges, etc. Other than standard double end belt grinders Amber can also manufacture customized belt grinders suitable for any particular application.
Amber manufactures Double End Abrasive Belt Grinders which accommodates a direct drive motor and serrated contact rubber wheels at both the ends of the motor and the attachments for mounting, tensioning and resting the belt are mounted on the motor side cover. The belt tensioning arm can be tilted easily from 0 to 90 degrees as per the application. A rotary ON – OFF Switch is mounted on the motor base. A fabricated or Cast Iron pedestal stand can be provided on special request. Belt tensioning can easily be done by just pulling down the handle which is loaded on a spring.A belt adjusting knob helps to easily adjust the belt on the wheel. A serrated contact rubber wheel behind the abrasive belt helps to effortlessly ground and finish castings, forgings, hardware, kitchenware, metal fabricated parts, plastic parts, glass edges, etc. Other than standard double end belt grinders Amber can also manufacture customized belt grinders suitable for any particular application.
MountingFoot (B3), Flange (B5), Face (B14) and combinations
ProtectionIP 55
Multispeed motor is a single motor with different combinations of any of the two or three speeds. Applications of these motors are wide and very beneficial as a single motor can run in different speeds with same output. In Amber dual speed motors any combination of any two poles is possible between 2, 4, 6 and 8 poles. In these motors the power at higher speed is much larger than at lower speed. It is because the torque demanded for this kind of applications varies as the square of the speed. The power ratings of two speed winding can be very different within certain limits which are determined by the torque or power at a certain speed of the driven machine or device by the motor.
In some applications the required torques and powers are identical to each other at different motor speeds for example milling and turning machine applications, also in some applications the required torques and powers can be different for example fan applications. Amber manufactures such motors in all the types of motors with dahlander as well as separate windings whichever is suitable. All the mechanical specifications and dimensions of the Dual speed Amber Motors are same as AN Series or AO Series.
Multispeed motor is a single motor with different combinations of any of the two or three speeds. Applications of these motors are wide and very beneficial as a single motor can run in different speeds with same output. In Amber dual speed motors any combination of any two poles is possible between 2, 4, 6 and 8 poles. In these motors the power at higher speed is much larger than at lower speed. It is because the torque demanded for this kind of applications varies as the square of the speed. The power ratings of two speed winding can be very different within certain limits which are determined by the torque or power at a certain speed of the driven machine or device by the motor.
In some applications the required torques and powers are identical to each other at different motor speeds for example milling and turning machine applications, also in some applications the required torques and powers can be different for example fan applications. Amber manufactures such motors in all the types of motors with dahlander as well as separate windings whichever is suitable. All the mechanical specifications and dimensions of the Dual speed Amber Motors are same as AN Series or AO Series.
Amber manufactures Double End Abrasive Belt Grinders which accommodates a direct drive motor and serrated contact rubber wheels at both the ends of the motor and the attachments for mounting, tensioning and resting the belt are mounted on the motor side cover. The belt tensioning arm can be tilted easily from 0 to 90 degrees as per the application. A rotary ON � OFF Switch is mounted on the motor base. A fabricated or Cast Iron pedestal stand can be provided on special request. Belt tensioning can easily be done by just pulling down the handle which is loaded on a spring.
A belt adjusting knob helps to easily adjust the belt on the wheel. A serrated contact rubber wheel behind the abrasive belt helps to effortlessly ground and finish castings, forgings, hardware, kitchenware, metal fabricated parts, plastic parts, glass edges, etc. Other than standard double end belt grinders Amber can also manufacture customized belt grinders suitable for any particular application.
Amber manufactures Double End Abrasive Belt Grinders which accommodates a direct drive motor and serrated contact rubber wheels at both the ends of the motor and the attachments for mounting, tensioning and resting the belt are mounted on the motor side cover. The belt tensioning arm can be tilted easily from 0 to 90 degrees as per the application. A rotary ON � OFF Switch is mounted on the motor base. A fabricated or Cast Iron pedestal stand can be provided on special request. Belt tensioning can easily be done by just pulling down the handle which is loaded on a spring.
A belt adjusting knob helps to easily adjust the belt on the wheel. A serrated contact rubber wheel behind the abrasive belt helps to effortlessly ground and finish castings, forgings, hardware, kitchenware, metal fabricated parts, plastic parts, glass edges, etc. Other than standard double end belt grinders Amber can also manufacture customized belt grinders suitable for any particular application.
Single phase vibratory motors manufactured at Amber are motors with heavy steel graded cast iron bodies and with adjustable unbalance masses at both ends suitable for vibrating any equipment used for emptying, dosing, testing, compacting, cleaning, screening, loosening, distributing, conveying or feeding. Single Phase Vibrating Motors from Amber come with a capacitor starter panel. Amber Vibrators are such designed that they generate maximum vibration with minimum input power.
These vibratory motors are totally enclosed dirt and dust proof constructed and the amplitude of vibration can be easily controlled in it. Heavy duty roller/ball permanently greased bearings ensure long, trouble free and maintenance free operation in Amber Vibratory motors. Applications of Vibratory motors are numerous as they can be used in batching plants, construction machines, small parts finishing or polishing machines, ceramic industries, demolishing and recycling units, mineral extraction machines, foundry equipments, etc.
Single phase vibratory motors manufactured at Amber are motors with heavy steel graded cast iron bodies and with adjustable unbalance masses at both ends suitable for vibrating any equipment used for emptying, dosing, testing, compacting, cleaning, screening, loosening, distributing, conveying or feeding. Single Phase Vibrating Motors from Amber come with a capacitor starter panel. Amber Vibrators are such designed that they generate maximum vibration with minimum input power.
These vibratory motors are totally enclosed dirt and dust proof constructed and the amplitude of vibration can be easily controlled in it. Heavy duty roller/ball permanently greased bearings ensure long, trouble free and maintenance free operation in Amber Vibratory motors. Applications of Vibratory motors are numerous as they can be used in batching plants, construction machines, small parts finishing or polishing machines, ceramic industries, demolishing and recycling units, mineral extraction machines, foundry equipments, etc.
Three phase AC Brake motors offered by Amber consist of AC Electromagnetic Fail Safe Brake Unit mounted on the non-drive end of the motor and coupled directly to the shaft of the motor. The brake in these motors will apply whenever the power to the brake is cut off. These motors are availed with or without cooling fan based on the application and requirement.
Application of AC Three phase brake motors are in lifts, hoists, conveyors and other applications where the frequency of switching the brake On-Off is very low. The major care to take while operating these motors is to check that power to motor and brake are cut off simultaneously otherwise the motor or brake may get damaged.
Three phase AC Brake motors offered by Amber consist of AC Electromagnetic Fail Safe Brake Unit mounted on the non-drive end of the motor and coupled directly to the shaft of the motor. The brake in these motors will apply whenever the power to the brake is cut off. These motors are availed with or without cooling fan based on the application and requirement.
Application of AC Three phase brake motors are in lifts, hoists, conveyors and other applications where the frequency of switching the brake On-Off is very low. The major care to take while operating these motors is to check that power to motor and brake are cut off simultaneously otherwise the motor or brake may get damaged.
Swing-frame grinder can be simply explained as any power driven rotatable grinding, polishing, or buffing wheel mounted in such a manner that the wheel with its supporting framework can be manipulated over stationary objects. Experience has shown that swing frame wheels can increase productivity 5 to 9 times over conventional portables. Mostly Swing Frame Grinders are used for high speed removal of gates and risers of heavy duty castings, forgings or fabricated parts which are difficult to move. These grinders are powered by a continuous duty TEFC squirrel cage low power consuming induction motor through a multiple "V" belt drive with single or double step belt adjustment. They are designed to work under severe duty environments. All the rotating parts in Amber Swing frame grinders being dynamically balanced the vibration is negligible. Deep groove sealed and appropriately greased bearings with normal clearance are fitted on the wheel shaft.
At the front end of the grinder; two handles are welded for handling the grinder while grinding. The grinding wheel is protected with the covers and the 'V' Belts with sheet metal belt guards. Robust and balanced fabrication minimises the transmission of vibrations to the operator. Above all; ergonomic design and length suitable for attaining a comfortable to-and-fro motion are taken care for developing Amber Swing Frame Grinders. Use of Swing Frame Grinders is for Stone finish, Automotive industry, Construction Industry , Wind power Industry, Railway Industry , Foundry-Forging Industry, Shipyards, Heat treatment, etc.
Swing-frame grinder can be simply explained as any power driven rotatable grinding, polishing, or buffing wheel mounted in such a manner that the wheel with its supporting framework can be manipulated over stationary objects. Experience has shown that swing frame wheels can increase productivity 5 to 9 times over conventional portables. Mostly Swing Frame Grinders are used for high speed removal of gates and risers of heavy duty castings, forgings or fabricated parts which are difficult to move. These grinders are powered by a continuous duty TEFC squirrel cage low power consuming induction motor through a multiple "V" belt drive with single or double step belt adjustment. They are designed to work under severe duty environments. All the rotating parts in Amber Swing frame grinders being dynamically balanced the vibration is negligible. Deep groove sealed and appropriately greased bearings with normal clearance are fitted on the wheel shaft.
At the front end of the grinder; two handles are welded for handling the grinder while grinding. The grinding wheel is protected with the covers and the 'V' Belts with sheet metal belt guards. Robust and balanced fabrication minimises the transmission of vibrations to the operator. Above all; ergonomic design and length suitable for attaining a comfortable to-and-fro motion are taken care for developing Amber Swing Frame Grinders. Use of Swing Frame Grinders is for Stone finish, Automotive industry, Construction Industry , Wind power Industry, Railway Industry , Foundry-Forging Industry, Shipyards, Heat treatment, etc.
Three phase DC Brake motors offered by Amber consist of DC Electromagnetic Fail Safe OR Normally off Brake Unit mounted on the non-drive end of the motor and coupled directly to the shaft of the motor. The brake unit being DC wound is powered through a rectifier or bridge. The brake in DC Fail Safe brake motors will apply whenever the power to the brake via rectifier or bridge is cut off and vice versa in the Normally off brake units.
These motors are availed with or without cooling fan based on the application and requirement. Application of DC Three phase brake motors are in machine tools and other applications where the frequency of switching the brake On-Off is very high. The major care to take while operating DC Fail Safe Brake motors is to check that power to motor and brake are cut off simultaneously otherwise the motor or brake may get damaged.
Three phase DC Brake motors offered by Amber consist of DC Electromagnetic Fail Safe OR Normally off Brake Unit mounted on the non-drive end of the motor and coupled directly to the shaft of the motor. The brake unit being DC wound is powered through a rectifier or bridge. The brake in DC Fail Safe brake motors will apply whenever the power to the brake via rectifier or bridge is cut off and vice versa in the Normally off brake units.
These motors are availed with or without cooling fan based on the application and requirement. Application of DC Three phase brake motors are in machine tools and other applications where the frequency of switching the brake On-Off is very high. The major care to take while operating DC Fail Safe Brake motors is to check that power to motor and brake are cut off simultaneously otherwise the motor or brake may get damaged.
Single phase AC Brake motors offered by Amber consist of AC Electromagnetic Fail Safe Brake Unit mounted on the non-drive end of the motor and coupled directly to the shaft of the motor. Amber Single phase DC Brake motors are available in all the three types (PSC, CSIR and CSCR) of single phase motors.The brake in Single phase AC Fail Safe brake motors will apply whenever the power to the brake is cut off.
Single phase AC Brake motors offered by Amber consist of AC Electromagnetic Fail Safe Brake Unit mounted on the non-drive end of the motor and coupled directly to the shaft of the motor. Amber Single phase DC Brake motors are available in all the three types (PSC, CSIR and CSCR) of single phase motors.The brake in Single phase AC Fail Safe brake motors will apply whenever the power to the brake is cut off.
Single phase vibratory motors manufactured at Amber are motors with heavy steel graded cast iron bodies and with adjustable unbalance masses at both ends suitable for vibrating any equipment used for emptying, dosing, testing, compacting, cleaning, screening, loosening, distributing, conveying or feeding. Single Phase Vibrating Motors from Amber come with a capacitor starter panel. Amber Vibrators are such designed that they generate maximum vibration with minimum input power.These vibratory motors are totally enclosed dirt and dust proof constructed and the amplitude of vibration can be easily controlled in it. Heavy duty roller/ball permanently greased bearings ensure long, trouble free and maintenance free operation in Amber Vibratory motors. Applications of Vibratory motors are numerous as they can be used in batching plants, construction machines, small parts finishing or polishing machines, ceramic industries, demolishing and recycling units, mineral extraction machines, foundry equipments, etc.
Single phase vibratory motors manufactured at Amber are motors with heavy steel graded cast iron bodies and with adjustable unbalance masses at both ends suitable for vibrating any equipment used for emptying, dosing, testing, compacting, cleaning, screening, loosening, distributing, conveying or feeding. Single Phase Vibrating Motors from Amber come with a capacitor starter panel. Amber Vibrators are such designed that they generate maximum vibration with minimum input power.These vibratory motors are totally enclosed dirt and dust proof constructed and the amplitude of vibration can be easily controlled in it. Heavy duty roller/ball permanently greased bearings ensure long, trouble free and maintenance free operation in Amber Vibratory motors. Applications of Vibratory motors are numerous as they can be used in batching plants, construction machines, small parts finishing or polishing machines, ceramic industries, demolishing and recycling units, mineral extraction machines, foundry equipments, etc.
Country of Origin415 V, 380 V, 220 V or as per requirement.
Frequency50 Hz/ 60 Hz or as per requirement.
Ambient Temperature50°C.
FrameIEC 63 to 132M.
Poles2, 4, 6 & 8
MountingFoot (B3), Flange (B5), Face (B14) and combinations.
ProtectionIP 55
InsulationF Class.
DutyS1.
EnclosureTEFC.
Temperature riseClass ‘B’ (80ºC).
BearingsSKF Double Sealed Ball Bearings .
Service Factor1 to 1.1.
Housing BodyCast Iron
AO Series Eff2 motors are Electric Motors with Standard Efficiency in accordance with IS 12615. All AO Series motors ranging from 71 to 132M are heavy duty, stout constructed and rugged motors completely manufactured and tested with latest available technology within our factory premises. Amber EFF2 motors are equipped with best CRNO magnetic lamination sheets, appropriately lubricated double sealed ball bearings and EN8 material grounded shafts.
These motors are wounded with modified polyester enameled copper wire (IS 13730, Part 03, Thermal Class 155°C) and insulation is Class E. Eff2 Amber motors are vibration free as rotors of these motors are dynamically balanced which also results into low maintenance cost. Terminal Box position of all the AO Series motors are on the right hand side as viewed from the shaft end which can be changed to left side on request.
AO Series Eff2 motors are Electric Motors with Standard Efficiency in accordance with IS 12615. All AO Series motors ranging from 71 to 132M are heavy duty, stout constructed and rugged motors completely manufactured and tested with latest available technology within our factory premises. Amber EFF2 motors are equipped with best CRNO magnetic lamination sheets, appropriately lubricated double sealed ball bearings and EN8 material grounded shafts.
These motors are wounded with modified polyester enameled copper wire (IS 13730, Part 03, Thermal Class 155°C) and insulation is Class E. Eff2 Amber motors are vibration free as rotors of these motors are dynamically balanced which also results into low maintenance cost. Terminal Box position of all the AO Series motors are on the right hand side as viewed from the shaft end which can be changed to left side on request.
Range : 0.18 to 5.5 KW:
Country of Origin : 415 V, 380 V, 220 V or as per requirement.
Secondary Business TypeManufacturer / Exporters / Wholesale Suppliers
Opening Hours
SUN : Closed
MON : 9:30 AM - 6:30 PM
TUE : 9:30 AM - 6:30 PM
WED : 9:30 AM - 6:30 PM
THU : 9:30 AM - 6:30 PM
FRI : 9:30 AM - 6:30 PM
SAT : 9:30 AM - 6:30 PM
Amber Engineering Enterprise, established in 1973, manufactures a wide range of A.C. Induction Electric Motors. In depth Electrical & Mechanical knowledge and a long experience in electrical line has helped Amber to develop near about 300 different models of A.C. Indcution Electric Motors, since the unit's establishment. Being oriented towards OEM customers Amber is more specialized in manufacturing custom built Electric Motors. The adoption of latest techniques in designing & developing, rigid quality control at all stages, use of best grade electrical, magnetic and insulating materials and skilled staff have helped in raising the image of AMBER as a quality and long life product maker. BUSINESS PHILOSOPHY: The Motto of the organization is to provide complete consumer satisfaction through quality in products using better & better technology and providing best services. 90% of the buyers of Amber Motors & Amar Panels being OEMs & EOUs which have technical persons preferring best quality. it seems that the above vision would never fragment from company's mind. PRODUCT PROFILE: Amber Engineering Enterprise offers A.C. induction Electric Motors ranging from 0.06 HP to 7.5 HP in 3 Phase in 2,4,6,& 8 Poles and from 0.06 HP to 2 HP in 1 Phase in 2 & 4 Poles. We supply Electric motors in all type of mountings i.e. Foot, Flange & Face. Other than Cast Iron bodies Aluminum Extrusion Bodies as well as Aluminum Die Cast bodies are used to produce Electric Motors by us as per customer requirement. Besides regular motor we produce A.C. & D.C. Brake type motors, Vibratory motors, Textile Duty Motors, Bench Grinders, Abrasive Belt Grinders, Polishing Machines, Cup wheel grinder Motors, Ink circulating pumps, Multi Speed Motors & Flexible Shaft Grinders For Export oriented customers we also manufacture Electric Motors with any type of input power (i.e. voltage & frequency) supplies in different countries. Other than above products we are more specialized in manufacturing various types of costume designed electric motors in which customer provides mechanical & mounting designs to suit to their machines. QUALITY: An Electric Motor is the heart of a machine. So better is the quality of Electric Motor better is the life and performance of the machine. Thus, Quality has always been a first preference for Amber against Cost. Each & Every motor is mechanically & electrically tested at all stages as per ISI. Electrical Designs have been evolved which have ample reserve torque, high starting torque, high efficiency & power factor capable of operating satisfactorily in fluctuating loads & supply voltage. Constant up gradation of quality aimed by us of satisfy costumer needs.
Reviews & Ratings
Write a Review
Post Free Ad