Sam Engineers Bhayandar, Thane, MH

We are trusted Manufacturer and Supplier of X Rings in Maharashtra. X Rings are four lobed seals with a specially developed sealing profile that actually provides twice the number of sealing surfaces as an O-ring. The four-lobed design not only provides lower fiction than an O-ring, but also, due to its square cross section, it resists spiral twist. X Rings Seals are available in a wide range of elastomeric materials for both standard and special applications. X Rings Seals are supplied to the American Standard AS-568A and are completely interchangeable with O-rings in these sizes. X Rings or Quad-Rings® Seals are available in all standard O-Ring sizes from 1/32" to 26", as well as custom seals for unique applications. Features There are two sealing surfaces to give a positive seal with less friction. Due to an improved pressure profile over Quad-Ring© Seal cross-section, a high sealing effect is achievedThe recessed mold parting line provides no flash or parting line on the surface of the seal and ensures "zero leakage." What's more, a lubricant reservoir formed between the sealing lips improves performance at start-upThe quad cross-section resists spiral twisting and extrusion. Due to its special profile, the seal does not tend to twist in the groove during reciprocating movementTwice the sealing surface means less radial squeeze is needed to create an effective seal resulting in less friction, less wear and longer service life

Available with us is the precision-made Wiper Seals. The Wiper Seals, we offer, are also known as Dirt Wipers, Scrappers or excluders and extensively used keep contaminants such as dirt, dust & moisture from entering the fluid power systems. The clients can avail the Wiper Seals from us at the most affordable price. Design Criteria Premature failure of seals or any component in fluid power system is due to contamination. Poor selection of wiper seal can result into failure of Rod seals. Design criteria for the wiper seal should not be limited to allow the proper fitment of rod seal (dynamic sealing ) but also sealing of housing ( static function ) has to be taken care of. Below mentioned are the various profiles of the wiper seal designed to suit the basic requirement of containing the contaminant. Design & selection criteria of the wiper seal is largely depend upon the surface speed of rod, fluid media, rod surface finish & speed. Single lip design or straight wiper lip design offers best scrapping & dirt removal performance. It is recommended for most sealing applications with high contamination. Single lip beveled wiper lip is less aggressive as it allows microscopically thin oil film to be retracted back into the system while providing adequate dirt exclusion in less contaminated environments. Wiper seal with double lip i.e internal as well as external lip provides best sealing performance. It eliminates built up fluid pressure between wiper & rod seal. For applications where equipment is exposed to highly contaminated with dirt, mud, moisture or where the position of the rod seals are such that it is possible for moisture or other contaminants to get past the wiper, leading to the corrosion or damage of components & seals. For these applications, we are offering special environment seals.

We, at sam engineers are engaged in manufacturing, exporting and supplying v ring seals. The v ring seals, also called as axial shaft seals, are manufactured as per the set industrial standards using well-tested material. The clients can avail the v ring seals from us in varied specifications as per the requirement at affordable price. v ring seals types all rubber v ring are known as v ring sealsmetal cased v ring seals parts of v ring seals the v-seal is comprised of three basic parts. The body of the seal holds it into place on the shaft or mounting surface. The cone shaped flexible lip rides in light contact with the counter surface and does the sealing. The resilient hinge joins the other two parts together and provides the force which keeps the lip against the counter surface. It is these three parts, working together, which allows simple one piece seal to do what no other seal system can do. installations the v-seal can be completely assembled without the need of tools. Being all rubber, it can stretch up to 250% of its molded i.d., so it can be easily stretched over flanges, collars, and entire bearing housings during assembly. This same resilience holds the seal in place without the need for springs or clamps. To assemble the seal, it is stretched onto the shaft by hand and then pushed up against the counter face to a pre-determined width. seal function one v-seal functions as three different seals. The simple v-seal lip keeps dirt and water out, grease in and acts as a slinger. The v-seal can be used alone to seal lubrication in and/or contamination out, or it can supplement an oil seal, mechanical seal or labyrinth, keeping contamination away from the primary seal. speed in most applications, the v-seal rotates with the shaft to provide a slinging action. As such, it is subject to centrifugal force. At speeds below 1600 surface feet per minute (fpm), the stretch tension of the v-seal is sufficient to hold it onto the shaft.above 1600 fpm, axial back up is required in the form of a step in the shaft or a snap-ring or lock collarabove 2400 fpm, radial back up is required in the form of a mounting pocket or clamp around the v-seal body. Above 3000 fpm, the lip of the v-seal lifts away from the counterface resulting in a clearance seal and eliminating drag and wear. The v-seal can also be mounted stationary and run against a rotating counterface. In this case, centrifugal force has no effect on the v-seal the v-seal should always have axial back up in oil applications the basic dimensions of the v-seals are as follows: (i.e for a v-25 a). d – the molded inside diameter of the v seal =0.87”d1 - the shaft range the v-seal is made to fit = .095-1.07d2 - the maximum i.d. Of the counterface = d1 + 0.08d3 - the minimum o.d. Of the counterface = d1 + 0.45a - i.d. Width of the v-seal = .018b - o.d. Width of the v-seal = 0.3c - v-seal cross section = 0.1 b1 – v-seal fitted width = 0.24+/-0.03 materials the v-seal is available in a variety of different rubber materials for various operating conditions. Nitrile, neoprene, hnbr, epdm and silicone v-seals can all be supplied. Our proprietary anti-friction treatment (aft) reduces the already low friction of the v-seal even further. food grade materials are available including fda and nsf approved rubbers. In addition, our compounding lab can develop specialty materials for particular applications. For additional information, see our materials section or contact our technical department. for more details on sizes available, elastomer suitability or for any further queries.

symmetrical seals manufactured by us are specifically meant for linear & reciprocating dynamic applications. The symmetrical design allows for interchangeability between rod & piston applications. As a result, it makes it popular for stock keeping & reduced inventory. The clients can avail the symmetrical seals from us in varied specifications as per the requirement.

We are offering rubber grommets are generally used whenever wire pass through punched sheet metal or plastic casings for this reason. Rubber molded and continuous strip grommets, also known as edge grommets, are manufactured in a wide variety of sizes and lengths expressly for this purpose. rubber grommets are usually a single piece which can be inserted by hand. Two piece hard plastic devices are available are available which also grip the wire that passes through. This is called strain relief and is often used on power supply cords that attach to a piece of equipment, to prevent a tug on the wire from stressing the electrical connections inside the equipment. sleeved grommets have a flexible extensive (sleeve), usually tapered or molded to flex increasingly towards the free end in order to prevent fracture of electrical insulation. material sbr grommetsbuna – n grommetsepdm grommetsneoprene grommetsviton grommetssilicon grommetsnatural rubber grommetsisoprene grommets grommet applications mechanically protects against the sharp edges of drilled or punched holes for wiring, cable, tubing, piping, hoses, airlines, rope & more. Used in appliances, motors, tools, cars, trucks, trailers, electronic equipment, toys, bikes, rvs, boats, pumps, furniture & more. hardness : 30 to 80 shore a durometer colors : black, oxide red, custom color availabl material temperature : 150of to 550of, depending on material. See material performance data for specific information.

We are one of the leading Manufacturers of Rubber Gaskets, which includes Punched Gaskets, Molded Gaskets. We utilize well-tested compounds / Sheets, which is made from the industrially produced Rubber, as a raw material. These Rubber Gaskets are high in quality and demanded widely by the clients for the precision range. Our Range of Gaskets includes Flange GasketsFull Face GasketsRing GasketsDie cut GasketsNeoprene GasketsViton GasketsEPDM GasketsSilicon GasketsHigh Temperature GasketsHigh Pressure GasketsHigh Temperature GasketsMolded Rubber GasketsElectrically Conductive GasketsSponge Rubber Gaskets

Avail from us the Rubber Diaphragms of premium grade quality. The Rubber Diaphragms, we supply, are made as per international standards and are known for their excellent service life. Fabric-reinforced diaphragms utilize a layer of an engineered fabric material as part of the diaphragm construction. This layer of fabric gives tremendous design flexibility. A very thin-walled diaphragm can withstand high pressures while remaining very flexible and responsive to minor pressure variations. Fabrics made of polyester, nylon and silk are commonly used for most applications, with Nomex fabric used for those applications exposed to high-temperature and for those applications that require extremely high-strength. All types of elastomers, such as, Nitrile, EPDM, Fluorocarbon, Neoprene, Silicone, Fluorosilicone, can be used in the fabric-reinforced diaphragms. Many diaphragm applications require that the rolling diaphragms be coated with rubber on both sides, commonly referred to as "double-coat" diaphragms. This type of rolling diaphragm is typically required when the application sees pressure on both sides of the diaphragm in two ways: First, by utilizing our proprietary double-coat molding process, we are able to provide double-coat diaphragms directly from rubber and fabric. Second, by developing and maintaining an inventory of standard "coated-fabrics" that is, fabric that is coated on both sides by a sub-contractor using a variety of materials. The selection of the proper double-coat process and materials requires an understanding of both the rubber and fabric used in its fabrication, as well as the overall geometry of the rolling diaphragm. Fabric Reinforced Diaphragms Offer Positive SealLow Spring RateNo LubricationNo Breakaway ForceNo frictionHigh StrengthFunctionality over wide pressure rangeLow costSimple designVersatilityDouble coated fabrics Molded Diaphragm Advantages Best No Leak SealNo LubricationLow FrictionLow hysteresisNo Spring RateNo Break Away FrictionLong Cycle LifeEffective in harsh environmentsConstant effective pressure areaLow assembly / Hardware costExceptional SensitivityAbility to operate under severe pressure

We are one of the leading Manufacturers of all types of Industrial Non metallic Bellows. Our Bellows have up to a 1:4 stretch ratio and provide chemical, heat, and oil resistance. We make protective rubber sleeves for everything from electrical components to rods in oil wells. Custom cuffing allows for superior connections than those made without cuffs, in terms of both safety and appearance. Our Rubber Bellows & sleeves can handle with bend radii as low as zero, with extreme temperatures ranges from 600o F all the way down to -20o F. In addition to the great range in temperature flexibility, they are also flame retardant. Purpose Bellows & Covers are used in machines, pipe lines, ducting, to prevent dust particles, metallic chips & other foreign particles to enter into precision or important part of the machine to avoid damage & ultimately down time of production cycles & enhance longer life of the machine / part. Shapes of Bellows Available Circular, Rectangular, Square Bellows, Hexagon Bellows, C type Bellows, Camera Type, Roller Guard. Advantages Of Rubber Bellows Reduce VibrationDampen sound vibrationCompensate lateral, torsion & angular movementsCompensate axial movementsMinimal face to face dimensionsLight WeightLow movement forces requiredReduced fatigue factorReduced heat lossCorrosion, erosion resistantNo gaskets

We are offering rod seals are considered to be one of the decisive factor for the functioning of the hydraulic cylinder. Leakage through the rod seal can cause accidents / environmental damages. It is important to properly pair the rod seal & wiper for the best sealing performance. If a less aggressive rod seal is paired with an aggressive wiper, the wiper can scrape off the microscopically thin film of oil that remains on the rod in microscopic surface imperfections during the return stroke, resulting in system leakage. The thickness of the oil film depends upon the surface finish, rod seal and surface speed of cylinder. type of rod seal single acting / unidirectional rod seals (capable of sealing from one side)double acting /bidirectional rod seals (capable of sealing from both sides)below mentioned are single acting as well as double acting rod seals being offered for different pressure, rod surface speed, pressure media.

We are recognized as a reliable Piston Seals Manufacturer and Supplier in Maharashtra. Piston seals are used where there are high demands of maintaining the high level of sealing performance in sealing during the service life. At Sam Engineers, both Single & Double Acting Piston Seals are designed with separate & integrated Back up ring & Guide Ring. However, the ultimate selection of piston seals has to be on the operating conditions of cylinder. Types of Piston Seals Single acting Piston SealsDouble Acting Piston Seals Selection Of Piston Seals The selection of Piston Seals is to a greater extent based on the type of cylinder in operation. For a single acting cylinder, it is always better to choose the seal design which provides optimum sealing surface wherein thinnest possible lubricant that can pass through between the gaps of seals & cylinder tube surfaceFor a double acting cylinder, it is always better to choose double acting piston seal instead of using two single acting cylinder piston seal as considering high pressure built up in the cylinder; there is always a possibility of breakdown of either of single acting seal

We are trusted Oil Seals Manufacturer and Supplier in Mumbai. The Oil Seals, we offer, are manufactured using well-tested raw material and are further tested at NABL accredited laboratories. The clients can avail the Oil Seals from us in varied specifications at the market leading price. Details In an Oil seal environment, there is shaft that is rotating inside a housing or bore. Because of the friction, there must be some clearance between the shaft & the bore. The function of the rotary seal / oil seal is to stop whatever fluid is inside from leaking out from the clearance. The oil seal may also be used to prevent outside material such as dirt from moving in the through the surface. "Dynamic sealing" is the relationship between the rotating shaft and the seal and is handled by the sealing element. A garter spring may used in the oil seal to increase the radial interference between the  oil seal lip and contact point on the shaft. In order to achieve this interference, the oil seal's ID must be slightly smaller than the diameter of the shaft. "Static sealing" is the relationship between the housing and the seal. In order to achieve this interference, the oil seal's OD must be slightly larger than the diameter of the housing or bore. An oil seal normally consists of three basic components: the sealing element, the metal case and the spring. The purpose of the sealing element is to stop the fluid from leaking between the shaft and housing. The metal case will give rigidity and strength to the seal while it is being held in the bore or recessed groove. The spring will help make the sealing element more effective. All materials must be selected depending on the environment in which the oil seal will function.

Sam Engineers is a trusted name for offering precision-made O Rings. O Ring is a torus or doughnut shaped object, generally made from an elastomer and is used primarily for sealing. O rings are used in two general design applications: Static (Non moving) & Dynamic (Moving) that may range from vacuum to over 60000psi for sealing flanges and O ring grooves. Confirms To AS568 StandardMetric StandardANSI StandardJIS2401 StandardMIL SpecificationsNAS standardsDIN Standard Available Materials of O Rings NBRH-NBRX-NBRNEOPRENEEPDMSILICON FLUROSILICONSBRFLUOROCARBON � VITON Download

Avail from us the Asbestos & Non Asbestos Gaskets that are fabricated as per the set standards using well-tested raw material. The Asbestos & Non Asbestos Gaskets are thoroughly checked and tested at NABL accredited laboratories by the experts. The clients can avail the Asbestos & Non Asbestos Gaskets from us in varied specifications at affordable price.